|
AECMA PREN 2894 |
Aerospace Series Nuts, Bi-Hexagonal, Self-Locking, with Counterbore, in Heat Resisting Nickel Base Alloy, Passivated, MoS2 Lubricated Classification : 1 550 MPa (at Ambient Temperature)/315 Degrees C-Edition P 1 |
|
AECMA PREN 2904 |
Aerospace Series Clamps - Saddle in Aluminium Alloy Dimensions - Masses-Issue P 2; Inactive for New Design See PREN 3730 |
|
AECMA PREN 2913 |
Aerospace Series Washers, Flat, Large Diameter Steel-Issue P 1 |
|
AECMA PREN 2913 |
Aerospace Series Washers, Flat, Large Diameter, in Alloy Steel, Cadmium Plated-Edition P 2 |
|
AECMA PREN 2925 |
Bolts with Double Hexagon Head, Relieved Shank, Long Thread, in Heat Resisting Steel FE-PA92HT (A286) Classification 900 MPa/650 Degrees Celsius |
|
AECMA PREN 2926 |
Bolts with Double Hexagon Head, Relieved Shank, Long Thread, in Heat Resisting Steel FE-PA92HT (A286) Silver Plated Classification 900 MPa/650 Degrees Celsius |
|
AECMA PREN 2927 |
Aerospace Series Bolts with Double Hexagon Head, Relieved Shank, Long Thread, in Heat Resisting Nickel Base Alloy NI-P100HT (Inconel 718) Classification : 1 275 MPa / 650 Degrees C-Issue P 2 |
|
AECMA PREN 2928 |
Aerospace Series Bolts with Double Hexagon Head, Relieved Shank, Long Thread, in Heat Resisting Nickel Base Alloy NI-P100HT (Inconel 718), Silver Plated Classification : 1 275 MPa / 650 Degrees C-Issue P 2 |
|
AECMA PREN 2947 |
Aerospace Series Steel FE-PA3004 (X10CrNi18-09) Air Melted Non Heat Treated Cold Drawn Wire a or D Less than or Equal to 2,3 mm-Edition P 2 |
|
AECMA PREN 2950 |
Aerospace series Test method Wrought heat resisting alloys Semi-finished products and parts Conditions for macrographic and micrographic examination Atlas of structures and defects-Edition P1 |
|
AECMA PREN 2952 |
Aerospace Series Heat Resisting Alloy NI-PH2601 Solution Treated and Cold Worked Bar for Forged Fasteners D Less Than or Equal to 50 mm 1270 MPa Less Than or Equal to Rm Less Than or Equal to 1550 MPa-Edition P 3 |
|
AECMA PREN 2952 |
Heat Resisting Nickel Base Alloy (Ni-P1OOHT) Solution Treated and Cold Worked Bar for Hot Upset Forging for Fasteners 3 Less Than or Equal to D Less Than or Equal to 30 mm |
|
AECMA PREN 2961 |
Aerospace Series Heat Resisting Alloy NI-PH2601 Solution Treated Bar for Machined Fasteners D is Less Than or Equal to 50 mm Rm is Greater Than or Equal to 1270 MPa-Edition P 2 |
|
AECMA PREN 2995-004 |
Aerospace Series Circuit Breakers, Single-Pole, Temperature Compensated, Rated Current 1 A to 25 A Part 004: With Signal Contact and Unified Mounting Hardware Centre-to-Centre Distance of Terminals 18 mm Product Standard-Edition P 2 |
|
AECMA PREN 2996-001 |
Aerospace Series Circuit Breakers, Three-Pole, Temperature Compensated, Rated Current 1 A to 25 A Part 001: Technical Specification-Edition P 2 |
|
AECMA PREN 2996-001 |
Aerospace Series Circuit Breakers, Three-Pole, Temperature Compensated, Rated Current 1 A to 25 A Part 001: Technical Specification-Edition P 3 |
|
AECMA PREN 2997-002 |
Aerospace Series Connectors, Electrical, Circular, Coupled by Threaded Ring, Operating Temperatures 175 Degrees Celsius Continuous, 200 Degrees Celsius Continuous, 260 Degrees Celsius Peak and Fire Resistant Part 002- Specification of Performance and Contact Arrangements-Issue P 1 |
|
AECMA PREN 2997-003 |
Aerospace Seried Connectors, Electrical, Circular, Coupled by Threaded Ring, Operating Temperatures 175 Degrees Celsius Continuous, 200 Degrees Celsius Continuous, 260 Degrees Celsius Peak and Fire Resistant Part 003- Square Flange Receptacle Product Standard-Issue P 1 |
|
AECMA PREN 2997-007 |
Aerospace Series Connectors, Electrical, Circular, Coupled by Threaded Ring, Fire Resistant or Non Fire-Resistant, Operating Temperatures - 65 Degrees C to 175 Degrees C Continuous, 200 Degrees C Continuous, 260 Degrees C Peak Part 007: Hermetic Receptacle with Round Flange Attached by Welding or Brazing Product Standard-Edition P 2 |
|
AECMA PREN 2997-010 |
Aerospace Series Connectors, Electrical, Circular, Coupled by Threaded Ring, Fire-Resistant or Non Fire-Resistant, Operating Temperatures - 65 Degrees C to 175 Degrees C Continuous, 200 Degrees C Continuous, 260 Degrees C Peak Part 010: Protective Cover for Plug Product Standard-Edition P 2 |
|
AECMA PREN 2997-012 |
Aerospace series Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures – 65 °C to 175 °C continuous, 200 °C continuous, 260 °C peak Part 012: Jam-nut for jam-nut receptacles Product standard-Edition P 1 |
|
AECMA PREN 3019 |
Aerospace Series Self-Locking Plate Nuts, Floating, Two-Lug, in Heat Resisting Steel FE-PA92HT (A286) Classification : 1 100 MPa (at Ambient Temperature) /650 Degrees C-Issue P 2 |
|
AECMA PREN 3027 |
Aerospace Series Test Method for Dry Film Lubricants Salt Spray Test-Edition 1 |
|
AECMA PREN 3049 |
Aerospace Series 0-Rings-Issue P 1 |
|
AECMA PREN 3054 |
Aerospace Series Bearings-Airframe Rolling Single Row Self-Aligning Roller Bearings in Steel Cadmium Plated Dimensions and Loads-Issue P 1 |
|
AECMA PREN 3074 |
Aerospace Series Drawing Annotation for Composite Laminate Structure-Edition P 2; Replaced by PREN 4408-2 |
|
AECMA PREN 3074 |
Aerospace Series Drawing Annotation for Composite Laminate Structure-Issue P 1 |
|
AECMA PREN 3080 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Tees, Reduced Branch with Thrust Wire Nut-Edition P 1 |
|
AECMA PREN 3081 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Ferrules, Welded, with Dynamic Beam Seal End, for Repair-Edition P 1 |
|
AECMA PREN 3082 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Unions, Bulkhead, with Weld End, for Repair-Edition P 1 |
|
AECMA PREN 3083 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Unions, Bulkhead, Long, Welded, for Repair-Edition P 1 |
|
AECMA PREN 3107 |
Aerospace Series Sealants Test Methods Determination of Soluble Chromates Content |
|
AECMA PREN 3114-1 |
Aerospace Series Test Method Microstructure of (a + b) Titanium Alloy Wrought Products Part 1: General Requirements-Edition P 1 |
|
AECMA PREN 3114-2 |
Aerospace Series Test Method Microstructure (a + b) Titanium Alloy Wrought Products Part 2: Microstructure of Bars, Sections, Forging Stock and Forgings-Edition P 1 |
|
AECMA PREN 3125 |
Aerospace Series Aluminium Alloy AL-C42201 T6 Investment Casting a Less Than or Equal to 20 mm-Edition P 2 |
|
AECMA PREN 3136 |
Aerospace Series Rivets, Solid, Universal Head, in Corrosion Resisting Steel FE-PA92HT, Passivated-Issue P 1 |
|
AECMA PREN 3151 |
Aerospace Series Plain Dowels in NI-P100HT (Inconel 718)-Issue P 1 |
|
AECMA PREN 3152 |
Aerospace Series Propulsion Standard Parts Nuts, Self-Locking, in Heat Resisting Steel FE-PA92HT (A286) Classification: 1100 MPa/425 Degrees Celsius Technical Specification-Issue P 1 |
|
AECMA PREN 3155-001 |
Aerospace series Electrical contacts used in elements of connection Part 001: Technical specification-Edition P 4 |
|
AECMA PREN 3155-003 |
Aerospace Series Electrical Contacts Used in Elements of Connection Part 003: Contacts, Electrical, Female Type A, Crimp, Class S Product Standard-Edition P 2 |
|
AECMA PREN 3155-012 |
Aerospace Series Electrical Contacts Used in Elements of Connection Part 012: Contacts, Electrical, Triaxial, Size 8, Male, Type D, Solder, Class R Product Standard-Edition P 2 |
|
AECMA PREN 3155-013 |
Aerospace Series Electrical Contacts Used in Elements of Connection Part 013 - Contacts, Electrical, Triaxial, Female 013, Type D, Solder, Class R - Product Standard-Issue P 1 |
|
AECMA PREN 3155-030 |
Aerospace series Electrical Contacts used in Elements of Connection Part 030: Contacts, Electrical, Coaxial, Shielded, Size 12, Male, Type D, Crimp, Class R Product Standard-Edition P 1 |
|
AECMA PREN 3155-031 |
Aerospace Series Electrical Contacts Used in Elements of Connection Part 031: Contacts, Electrical, Coaxial, Shielded, Size 12, Female, Type D, Crimp, Class R Product Standard |
|
AECMA PREN 3155-070 |
Aerospace series Electrical contacts used in elements of connection Part 070: Contacts, electrical, male, type A, crimp, class S Product standard-Edition P 1 |
|
AECMA PREN 3201 |
Aerospace Series Design Standard Holes for Metric Threaded Fasteners-Edition 1 |
|
AECMA PREN 3201 |
Aerospace Series Design Standard Holes for Metric Threaded Fasteners-Issue P 1 |
|
AECMA PREN 3207 |
Aerospace Series Rubber Compounds Technical Specification-Edition 1 |
|
AECMA PREN 3228 |
Aerospace Series Nuts, Hexagon, Plain, Reduced Height, Normal Across Flats, in Steel, Cadmium Plated Classification: 900 MPa (at Ambient Temperature) / 235 Degrees Celsius-Edition P 1 |
|
AECMA PREN 3235-3 |
Aerospace Series Heat Resisting Alloys Wrought Products Technical Specification Part 3 - Bar and Section-Edition P 2 |
|
AECMA PREN 3235-4 |
Aerospace Series Heat Resisting Alloys Wrought Products Technical Specification Part 4 - Seamless Tube-Edition P 2 |
|
AECMA PREN 3240 |
Aerospace Series Nuts, Self-Locking, Clip, in Heat Resisting Steel FE-PA92HT (A286), Uncoated Classification: 1 100 MPa (at Ambient Temperature) / 425 Degrees Celsius-Issue P 2 |
|
AECMA PREN 3241 |
Aerospace Series Nuts, Self-Locking, Clip, in Heat Resisting Steel FE-PA92HT (A286), Silver Coated Classification: 1 100 MPa (at Ambient Temperature) / 425 Degrees Celsius-Issue P 2 |
|
AECMA PREN 3243 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Ferrule, Welded, with Dynamic Beam Seal End-Issue P 1 |
|
AECMA PREN 3253 |
Aerospace Series Pipe Coupling 8 Degree 30' in Titanium Alloy Elbow 90 Degree Bulkhead-Edition P 2; Replaced by PREN 4021 |
|
AECMA PREN 3257 |
Aerospace Series Pipe Coupling 8 Degree 30' in Titanium Alloy Elbow 45 Degree, Bulkhead-Edition P 2; Replaced by PREN 4025 |
|
AECMA PREN 3267 |
Aerospace Series Washer, Bulkhead in Titanium Alloy-Issue P 1 |
|
AECMA PREN 3272 |
Aerospace Series Pipe Coupling 8 Degrees 30' Dynamic Beam Seal End for Nipple, Welded Geometric Configuration-Issue P 1 |
|
AECMA PREN 3274 |
Aerospace Series Pipe Coupling 8 Degrees 30' Thread End Geometric Configuration-Issue P 1 |
|
AECMA PREN 3276 |
Aerospace Series Clamps, Loop ( |
|
AECMA PREN 3284 |
Aerospace Series Bearings-Airframe Rolling Rigid, Single Row Ball Bearings in Steel Diameter Series 0 and 2 Normal Clearance Category Dimensions, Torques, and Loads-Issue P 1 |
|
AECMA PREN 3296 |
Rings, Threaded, Self- Locking, Silver-Coated in FE-PA92HT(A286) |
|
AECMA PREN 3298 |
Aerospace Series Inserts, Thin Wall Installation and Removal Procedure-Edition P 1 |
|
AECMA PREN 3298 |
Aerospace series Inserts, thin wall, self-locking Installation and removal procedure-Edition P 2 |
|
AECMA PREN 3299 |
Aerospace Series Shaft-Nuts and Threaded Rings, Self-Locking, Right- or Left-Hand MJ Threads, in Heat Resisting Steel FE-PA2601 (A286), Silver Plated Technical Specification-Edition P 1 |
|
AECMA PREN 3301 |
Aerospace Series Bolts, T-Head, Close Tolerance Medium Thread Length in Heat Resisting Steel FE-PM38 (FV535), Uncoated Classification : 1000 MPa/550 Degrees Celsius-Issue P 1 |
|
AECMA PREN 3312 |
Titanium Alloy TI-P63 Annealed 900 Less Than or Equal to Rm Less Than or Equal to 1160 MPa Forgings De Less Than or Equal to 150 mm |
|
AECMA PREN 3314 |
Titanium Alloy TI-P63 Solution Treated and Aged Rm Greater Than or Equal to 1070 MPA Bar for Machining De Less Than or Equal to 50 mm |
|
AECMA PREN 3335 |
Aerospace Series Aluminium Alloy (7475) Solution Treated and Artificially Aged (T762) Sheet for Super-Plastic Forming 0,8 Less Than or Equal to a Less Than or Equal to 6 mm-Issue P 1 |
|
AECMA PREN 3335 |
Aerospace Series Aluminium Alloy AL-P7475-O2 Sheet for Super-Plastic Forming (SPF) 0,8 Less Than or Equal to a Less Than or Equal to 6 mm-Edition P 2 |
|
AECMA PREN 3335 |
Aerospace Series Aluminium Alloy AL-P7475-O2 Sheet for Superplastic Forming (SPF) 1,0 mm Less Than or Equal to a Less Than or Equal to 6 mm |
|
AECMA PREN 3341 |
Aerospace Series Aluminium Alloy (6061) Solution Treated, Water Quenched and Aged (T4) Sheet and Strip 0,4 Less Than or Equal to a Less Than or Equal to 6 mm-Issue P 1 |
|
AECMA PREN 3341 |
Aerospace Series Aluminium Alloy AL-P6061-T4 or T42 Sheet and Strip 0,4 mm Less Than or Equal to a Less Than or Equal to 6 mm-Edition P2 |
|
AECMA PREN 3344 |
Aerospace Series Aluminium Alloy AL-P7050-T76511 Extruded Bars and Section a or D Less Than or Equal to 150 mm with Peripheral Coarse Grain Control-Edition P 3 |
|
AECMA PREN 3346 |
Aerospace Series Aluminium Alloy AL-P2014A-T3 Drawn Tube for Structural Applications 0,6 mm Less Than or Equal to a Less Than or Equal to 12,5 mm-Edition P 2 |
|
AECMA PREN 3347 |
Aerospace Series Aluminium Alloy AL-P2024-T8511 Extruded Bar and Section a or D Less Than or Equal to 150 mm with Peripheral Coarse Grain Control-Edition P 3 |
|
AECMA PREN 3353 |
Aerospace Series Titanium Alloy TI-P63 Solution Treated and Aged Rm Greater Than or Equal to 1100 MPa Bar and Wire for Fasteners Machined De Less Than or Equal to 25 mm-Issue P 2; Inactive for New Design See PREN 3813 |
|
AECMA PREN 3354 |
Aerospace Series Titanium Alloy TI-P63 Annealed 920 Less Than or Equal to Rm Less Than or Equal to 1180 MPa Sheet for Superplastic Forming a Less Than or Equal to 6 mm Issue P 1 |
|
AECMA PREN 3361 |
Aerospace Series Steel FE-PM64 Solution Annealed and Precipitation Hardened Rm Greater Than or Equal to 1070 MPa Sheet and Strip a Less Than or Equal to 6 mm-Issue P 1 |
|
AECMA PREN 3367 |
Aerospace Series Steel FE-PL10 Hardened, Tempered and Cold Drawn 1260 Less Than or Equal to Rm Less Than or Equal to 2790 MPa Wire for Spring 0,20 Less Than or Equal to D Less Than or Equal to 10,50 mm-Issue P 1 |
|
AECMA PREN 3372-003 |
Aerospace Series Connectors, Electrical, Circular, Medium and High Contact Density, Scoop-Proof with Bayonet Coupling, Operating Temperatures - 65 Degrees C to 175 Degrees C or 200 Degrees C Continuous Part 003: Square Flange Receptacle - Product Standard-Edition P 1 |
|
AECMA PREN 3372-004 |
Aerospace Series Circular Electrical Connectors Medium and High Density, Scoop-Proof with Bayonet Coupling, 175 Degrees Celsius and 200 Degrees Celsius Type B, Fixed Connector, Single-Hole Assembly Individual Sheet |
|
AECMA PREN 3372-005 |
Aeropsace Series Connectors, Electrical, Circular, Medium and High Contact Density, Scoop-Proof with Bayonet Coupling, Operating Temperatures - 65 Degrees C to 175 Degrees C or 200 Degrees C Continuous Part 005: Receptacle, Hermetic, Round Flange, Solder Mounting - Product Standard-Edition P 1 |
|
AECMA PREN 3372-006 |
Aeropsace Series Connectors, Electrical, Circular, Medium and High Contact Density, Scoop-Proof with Bayonet Coupling, Operating Temperatures - 65 Degrees C to 175 Degrees C or 200 Degrees C Continuous Part 006: Protective Cover for Receptacle - Product Standard-Edition P 1 |
|
AECMA PREN 3372-009 |
Aeropsace Series Connectors, Electrical, Circular, Medium and High Contact Density, Scoop-Proof with Bayonet Coupling, Operating Temperatures - 65 Degrees C to 175 Degrees C or 200 Degrees C Continuous Part 009: Receptacle, Jam Nut Mounting Product Standard-Edition P 1 |
|
AECMA PREN 3372-012 |
Aeropsace Series Circular Electrical Connectors Medium and High Density, Scoop-Proof with Bayonet Coupling, 175 Degrees C and 200 Degrees C Type W, Dummy Individual Sheet |
|
AECMA PREN 3372-013 |
Aeropsace Series Circular Electrical Connectors Medium and High Density, Scoop-Proof with Bayonet Coupling, 175 Degrees C and 200 Degrees C Type P, Fixed Connector, Square Flange without Rear Accessory Individual Sheet |
|
AECMA PREN 3380 |
Aerospace Series Retaining Rings Technical Specification-Issue P 1 |
|
AECMA PREN 3382 |
Aerospace Series Rings Retaining, Internal, Axial Mounting, Steel, Phosphated-Issue P 1 |
|
AECMA PREN 3383 |
Aerospace Series Rings Retaining, Internal, Axial Mounting, Steel, Vacuum Cadmium Plated-Issue P 1 |
|
AECMA PREN 3388 |
Aerospace Series Bolts, Screws and Studs in Heat Resisting Nickel Base Alloy NI-P100HT (Inco 718) Classification : 1275 MPa/650 Degrees Celsius Technical Specification-Issue P1; Supersede C 8 |
|
AECMA PREN 3391 |
Aerospace Series Rivets, Solid, Universal Head, in Aluminium Alloy 2117, Metric Series-Issue P 1 |
|
AECMA PREN 3393 |
Aerospace Series Rivets, Solid, 100 Degrees Normal Countersunk Head with Dome, in Aluminium Alloy 2117, Metric Series-Issue P 1 |
|
AECMA PREN 3397 |
Aerospace Series Rivets, Solid, Universal Head, in Aluminium Alloy 7050, Metric Series-Issue P 1 |
|
AECMA PREN 3401 |
Aerospace Series Rivets, Solid, 100 Degree Normal Countersunk Head, in Aluminium Alloy 7050, Metric Series-Issue P 1 |
|
AECMA PREN 3404 |
Aerospace Series Rivets, Solid, Universal Head, in Aluminium Alloy 5056A, Anodized or Chromated, Metric Series-Issue P 1 |
|
AECMA PREN 3410 |
Aerospace Series Rivets, Solid, 100 Degree Normal Countersunk Head, in Aluminium 1050A, Metric Series-Edition P 1 |
|
AECMA PREN 3424 |
Aerospace Series Rivets, Solid, Universal Head, in Titanium-Columbium- Alloy Ti 45 5 Cb, Metric Series-Issue P1 |
|
AECMA PREN 3431 |
Aerospace Series Nuts, Hexagonal, Self-Locking, with Counterbore and Captive Washer, in Heat Resisting Steel, Silver Plated Classification: 1 100 MPa (at Ambient Temperature)/425 Degrees Celsius-Edition P 1 |
|
AECMA PREN 3433 |
Aerospace Series Lockwashers, Heat Resisting Steel, Passivated-Edition P 2; Withdrawn - Not Replaced |
|
AECMA PREN 3434 |
Aerospace Series Nuts, Hexagon, Slotted, Self-Locking, in Steel, Cadmium Plated, MoS2 Lubricated Classification: 900 MPa (at Ambient Temperature)/235 Degrees C-Issue P 1 |
|
AECMA PREN 3441 |
Titanium TI-PO1 Annealed 290 Less Than or Equal to Rm Less Than or Equal to 420 MPa Sheet and Strip, Hot Rolled A Less Than or Equal to 6 mm |
|
AECMA PREN 3457 |
Aerospace Series Titanium Alloy TI-P63 Not Heat Treated Reference Heat Treatment: Solution Treated and Aged Grade 2 Forging Stock for Fasteners D Less Than or Equal to 25 mm-Issue P 2; Inactive for New Design See PREN 3813 |
|
AECMA PREN 3464 |
Aerospace Series Titanium Alloy TI-P63 Annealed 900 Less Than or Equal to Rm Less Than or Equal to 1160 MPa Plate 6 Less Than a Less Than or Equal to 100 mm-Issue P 1 |
|
AECMA PREN 3468 |
Aerospace Series Steel FE-PA13 Softened 500 Less Than or Equal to Rm Less Than or Equal to 700 MPa Forgings De Less Than or Equal to 100 mm-Issue P 1 |
|
AECMA PREN 3469 |
Aerospace Series Steel FE-PM1802 (X5CrNiCu15-5) Consumable Electrode Remelted Solution Treated and Precipitation Treated Forgings a or D Less than or Equal to 200 mm Rm Greater than or Equal to 1 310 MPa-Edition P 3 |
|
AECMA PREN 3470 |
Aerospace Series Steel FE-PM1503 (X3CrNiMoAI13-8-2) Vacuum Induction Melted and Consumable Electrode Remelted Solution Treated and Precipitation Treated Forgings a or D Less Than or Equal to 150 mm 1 200 MPa Less Than or Equal to Rm Less Than or Equal to 1 400 MPa-Edition P2 |
|
AECMA PREN 3474 |
Aerospace Series Aluminium Alloy AL-P2024-T81 Sheet and Strip 0,25 mm Less Than or Equal to a Less Than or equal to 6 mm-Issue P 3 |
|
AECMA PREN 3475-302 |
Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 302: Voltage Proof Test-Issue P 2 |
|
AECMA PREN 3475-303 |
Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 303 - Insulation Resistance-Issue P 1 |
|
AECMA PREN 3475-306 |
Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 306: Continuity of Conductors-Edition P 1 |
|
AECMA PREN 3475-704 |
Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 704: Flexibility-Edition P 1 |
|
AECMA PREN 3475-704 |
Aerospace series Cables, electrical, aircraft use Test methods Part 704: Flexibility-Edition P 2 |
|
AECMA PREN 3475-801 |
Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 801: Capacitance Per Unit Length-Edition P 1 |
|
AECMA PREN 3475-807 |
Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 807: Transfer Impedance-Edition P 1 |
|
AECMA PREN 3475-808 |
Aerospace Series Cables, Electrical, Aircraft Use Test Methods Part 808: Cross-Talk-Edition P 1 |
|
AECMA PREN 3476-009 |
Aerospace Series Connectors, Electrical, Circular, Bayonet Coupling, Operating Temperature 175 Degrees C or 200 Degrees C Continuous Part 009: Protective Cover for Receptacle Product Standard-Edition P 1 |
|
AECMA PREN 3477 |
Aerospace Series Steel FE-PM3503 (X7CrNiMo15-7-3) Air Melted Solution Treated and Precipitation Treated Plate 6 mm Less Than a Less Than or Equal to 15 mm 1 310 MPa Less Than or Equal to Rm Less Than or Equal to 1 550 MPa-Edition P 2 |
|
AECMA PREN 3478 |
Aerospace Series Steel FE-PM63 Solution Annealed Transformation Treated and Precipitation Hardened 1310 Less Than or Equal to Rm Less Than or Equal to 1550 MPa Sheet and Strip a Less Than or Equal to 6 mm-Issue P 1 |
|
AECMA PREN 3479 |
Aerospace Series Steel FE-PM1802 (X5CrNiCu15-5) Consumable Electrode Remelted Solution Treated and Precipitation Treated Plate 6 mm Less Than or Equal to a Less Than or Equal to 20 mm 1 070 MPa Less Than or Equal to Rm Less Than or Equal to 1 220 MPa-Edition P 3 |
|
AECMA PREN 3483 |
Aerospace Series Steel FE-CM3801 (X5CrNiCu16-4) Homogenized, Solution Treated, Precipitation Hardened and Sub Zero Sand or Investment Casting Rm Greater Than or Equal to 1 240 MPa-Edition P2 |
|
AECMA PREN 3486 |
Aerospace Series Steel FE-PM67 Solution Annealed and Precipitation Hardened 1400 Less Than or Equal to Rm Less Than or Equal to 1550 Mpa Forgings De Less Than or Equal to 100 mm-Issue P 1 |
|
AECMA PREN 3487 |
Aerospace Series Steel FE-PA13 Softened 500 Less Than or Equal to Rm Less Than or Equal to 700 MPa Bar for Machining De Less Than or Equal to 100 mm-Issue P 1 |
|
AECMA PREN 3489 |
Aerospace Series Steel FE-PA13 Softened 500 Less Than or Equal to Rm Less Than or Equal to 750 MPa Tubes for Structures 0,5 Less Than or Equal to a Less Than or Equal to 5 mm-Issue P 1 |
|
AECMA PREN 3490 |
Aerospace Series Steel FE-PL3901 (X15CrNi17-3) Air Melted Hardened and Tempered Bar for Machining De Less Than or Equal to 200 mm 900 MPa Less Than or Equal to Rm Less Than or Equal to 1 100 MPa-Edition P2 |
|
AECMA PREN 3490 |
Aerospace Series Steel FE-PM42 Hardened and Tempered 900 Less Than or Equal to Rm Less Than or Equal to 1100 MPa Bar for Machining De Less Than or Equal to 100 mm-Issue P 1 |
|
AECMA PREN 3491 |
Aerospace Series Steel FE-PL3901 (X15CrNi17-3) Air Melted Hardened and Tempered Forgings De Less Than or Equal to 100 mm 900 MPa Less Than or Equal to Rm Less Than or Equal to 1 100 Mpa-Edition P2 |
|
AECMA PREN 3493 |
Aerospace Series Steel FE-PL48 Hardened and Tempered 1050 Less Than or Equal to Rm Less Than or Equal to 1250 MPa Forgings De Less Than or Equal to 40 mm-Issue P 1 |
|
AECMA PREN 3497 |
Aerospace Series Titanium TI-P99001 Annealed Sheet and Strip, Cold Rolled a Less Than or Equal to 6 mm 290 MPa Less Than or Equal to Rm Less Than or Equal to 420 MPa-Edition P 2 |
|
AECMA PREN 3498 |
Aerospace Series Titanium TI-P99002 Annealed Sheet and Strip, Cold Rolled a Less Than or Equal to 6 mm 390 MPa Less Than or Equal to Rm Less Than or Equal to 540 MPa-Edition P 2 |
|
AECMA PREN 3499 |
Aerospace Series Titanium TI-P99003 Annealed Sheet and Strip, Cold Rolled a Less Than or Equal to 6 mm 570 MPa Less Than or Equal to Rm Less Than or Equal to 730 MPa-Edition P 2 |
|
AECMA PREN 3500 |
Aerospace Series Titanium Alloy TI-P11 Annealed 540 Less Than or Equal to Rm Less Than or Equal to 700 MPa Sheet and Strip a Less Than or Equal to 6 mm-Edition P 2; Inactive for New Design see PREN 3859 and PREN 3850 |
|
AECMA PREN 3506 |
Aerospace Series Hot Rolled Sheets and Plates in Heat Resisting Alloys Thickness 2,0 mm Less Than or Equal to a Less Than or Equal to 100 mm Dimensions-Edition P 1 |
|
AECMA PREN 3517 |
Steel FE-PL73 Hardened and Tempered 1080 Less Than or Equal to Rm Less Than or Equal to 1280 MPa Bar for Machining De Less Than or Equal to 150 mm |
|
AECMA PREN 3522 |
Aerospace Series Steel FE-PL79 Softened Reference Heat Treatment: Carburized, Hardened and Tempered Forging Stock De Less Than or Equal to 200 mm-Issue P 1 |
|
AECMA PREN 3523 |
Aerospace Series Steel FE-PL1505 (15CrMoV6) Air Melted Hardened and Tempered Bar for Machining De Less Than or Equal to 100 mm 1 080 MPa Less Than or Equal to Rm Less Than or Equal to 1 280 MPa-Edition P 2 |
|
AECMA PREN 3524 |
Aerospace Series Steel FE-PL1505 (15CrMoV6) Air Melted Hardened and Tempered Sheet and Strip 2 mm Less Than or Equal to a Less Than or Equal to 6 mm 1 080 MPa Less Than or Equal to Rm Less Than or Equal to 1 280 MPa-Edition P 2 |
|
AECMA PREN 3525 |
Aerospace Series Steel FE-PL1505 (15CrMoV6) Air Melted Hardened and Tempered Plate 6 mm Less Than or Equal to a Less Than or Equal to 20 mm 1 080 MPa Less Than Rm Less Than or Equal to 1 280 MPa-Edition P 2 |
|
AECMA PREN 3526 |
Aerospace Series Steel FE-PL1505 (15CrMoV6) Air Melted Hardened and Tempered Sheet and Strip 0,5 mm Less Than or Equal to a Less Than or Equal to 6 mm 980 MPa Less Than Rm Less Than or Equal to 1 180 MPa-Edition P 2 |
|
AECMA PREN 3529 |
Aerospace Series Steel FE-PA95 Solution Treated and Precipitation Treated 1750 Less Than or Equal to Rm Less Than or Equal to 2000 MPa Forgings De Less Than or Equal to 150 mm-Issue P 1 |
|
AECMA PREN 3537 |
Aerospace Series Nuts, Anchor, Self-Locking, Fixed, Two Lug, with Counterbore, in Heat Resisting Steel, MoS2 Lubricated Classification : 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius-Edition P 1; Corrigendum 5/10/93 |
|
AECMA PREN 3545-003 |
Aerospace Series Connectors, Electrical, Rectangular, with Sealed and Non-Sealed Rear, Plastic Housing, Locking Device, Operating Temperatures - 55 Degrees C to 175 Degrees C Part 003 : Connectors with Female Contacts Product Standard-Edition P 2 |
|
AECMA PREN 3553 |
Aerospace Series Aluminium Alloy AL-P2618A T6511 Extruded Bar and Section a or D Less Than or Equal to 160mm-Edition P 2 |
|
AECMA PREN 3564 |
Aerospace Series Pipe Coupling 80 Degree 30 Feet in Titanium Alloy Tee, Bulkhead Long Fitting on Limb-Edition 1 |
|
AECMA PREN 3565-2 |
Aerospace Series Pipe Couplings, 37 Degree, Spherical, in Heat Resisting Steel Geometrical Configuration Port Ends Inch Series |
|
AECMA PREN 3612 |
Aerospace Series Undercuts for Splines-Issue P 1 |
|
AECMA PREN 3615 |
Aerospace Series Fibre Reinforced Plastics Procedure for the Determination of the Conditions of Exposure to Humid Atmosphere and the Determination of Moisture Absorption-Edition 11 |
|
AECMA PREN 3628 |
Aerospace Series Lockwire Drawn Corrosion Resisting Steel-Issue P 1 |
|
AECMA PREN 3633 |
Aerospace Series Installation Hole for Fluid Fittings, Flanged-Edition P 1 |
|
AECMA PREN 3645-001 |
Aerospace Series Connectors, Electrical, Circular, Scoop-Proof, Triple Start Threaded Coupling Operating Temperatures 175 Degrees C or 200 Degrees C Continuous Part 001 - Technical Specification-Edition: 3E |
|
AECMA PREN 3645-001 |
Aerospace Series Connectors, Electrical, Circular, Scoop-Proof, Triple Start Threaded Coupling, Operating Temperature 175 Degrees Celcius or 200 Degrees Celsius Continuous Part 001: Technical Specification-Edition P 1 |
|
AECMA PREN 3645-003 |
Aerospace series Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling operating temperature 175 degrees C or 200 degrees C continuous Part 003: Wall-mount receptacle Product standard-Edition P1 |
|
AECMA PREN 3645-003 |
Aerospace Series Connectors, Electrical, Circular, Scoop-Proof, Triple Start Threaded Coupling Operating Temperatures 175 Degrees C or 200 Degrees C Continuous Part 003 - Wall-Mount Receptacle Product Standard-Edition: 11E |
|
AECMA PREN 3645-006 |
Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling operating temperature 175 degrees C or 200 degrees C continuous Part 006: Protective cover for receptacle - Product standard-Edition P 1 |
|
AECMA PREN 3645-007 |
Aerospace Series Connectors, Electrical, Circular, Scoop-Proof, Triple Start Threaded Coupling Operating Temperatures 175 Degrees C or 200 Degrees C Continuous Part 007 - Flight Cap for Plug Product Standard-Edition: 11E |
|
AECMA PREN 3645-012 |
Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling operating temperature 175 degrees C or 200 degrees C continuous Part 012: Lanyard release plug with grounding fingers Type 2 Product standard-Edition P1 |
|
AECMA PREN 3646-001 |
Aerospace Series Connectors, Electrical, Circular, Bayonet Coupling - Operating Temperature 175 Degrees Celsius or 200 Degrees Celsius Continuous Part 001: Technical Specification-Edition P 1 |
|
AECMA PREN 3646-006 |
Aerospace Series Connectors, Electrical, Circular, Bayonet Coupling - Operating Temperature 175 Degrees C or 200 Degrees C Continuous Duty Part 006 - Jam-Nut Mounted Round Flange Hermetic Receptacle-Edition: 5E |
|
AECMA PREN 3653 |
Aerospace Series Nuts, Anchor, Self-Locking, Floating, Self-Aligning, One Lug, in Steel, Cadmium Plated, MoS2 Lubricated Classification: 900 MPa (at Ambient Temperature)/235 Degrees C-Edition P 1 |
|
AECMA PREN 3660-001 |
Aerospace Series Cable Outlet Accessories for Circular and Rectangular Electrical and Optical Connectors Part 001: Technical Specification-Edition P 2 |
|
AECMA PREN 3660-003 |
Aerospace Series Cable Outlet Accessories for Circular and Rectangular Electrical and Optical Connectors Part 003: Grommet Nut, Style A for EN 2997 and EN 4067 Product Standard-Edition P 2 |
|
AECMA PREN 3660-003 |
Aerospace Series Part 003 - Detail Specification Sheet. Grommet Nut, Style A. |
|
AECMA PREN 3661-001 |
Aerospace Series Circuit Breakers, Single-Pole, Temperature Compensated, Rated Current 20 A to 50 A Part 001: Technical Specification-Edition P 1 |
|
AECMA PREN 3661-001 |
Aerospace Series Circuit Breakers, Single-Pole, Temperature Compensated, Rated Current 20 A to 50 A Part 001: Technical Specification-Edition P 2 |
|
AECMA PREN 3661-005 |
Aerospace Series Circuit Breakers, Single-Pole, Temperature Compensated, Rated Current 20 A to 50 A Part 005: With Polarized Signal Contact and Unified Mounting Hardware Centre-to-Centre Distance of Terminals 21 mm Product Standard-Edition P 1 |
|
AECMA PREN 3661-006 |
Aerospace Series Circuit Breakers, Single-Pole, Temperature Compensated, Rated Current 20 A to 50 A Part 006: With Polarized Signal Contact Bus Bar Version Product Standard-Edition P 3 |
|
AECMA PREN 3662-001 |
Aerospace Series Circuit Breakers, Three-Pole, Temperature Compensated, Rated Current 20 A to 50 A Part 001: Technical Specification-Edition P 2 |
|
AECMA PREN 3662-006 |
Aerospace Series Circuit Breakers, Three-Pole, Temperature Compensated, Rated Current 20 A to 50 A Part 006: With Polarized Signal Contact and Unified Mounting Hardware Bus-Bar Version Product Standard-Edition P 2 |
|
AECMA PREN 3662-006 |
Aerospace Series Circuit Breakers, Three-Pole, Temperature Compensated, Rated Current 20 A to 50 A Part 006: With Polarized Signal Contact Bus-Bar Version Product Standard-Edition P 3 |
|
AECMA PREN 3682-002 |
Aerospace Series Connectors, Plug and Receptacle, Electrical, Rectangular, Interchangeable Insert Type, Rack to Panel, Operating Temperature 150 Degrees C Continuous Part 002: Specification of Performance and Contact Arrangements-Edition P 1 |
|
AECMA PREN 3682-003 |
Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 degrees C continuous Part 003: Inserts Product standard-Edition P 1 |
|
AECMA PREN 3682-005 |
Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 degrees C continuous Part 005: Size 2 plug Product standard-Edition P 1 |
|
AECMA PREN 3682-007 |
Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 degrees C continuous Part 007: Size 3 plug Product standard-Edition P 1 |
|
AECMA PREN 3684 |
Aerospace Series Test Methods Titanium Alloy Wrought Products Determination of Beta Ray Transus Temperature Metallographic Method-Edition P 1 |
|
AECMA PREN 3685 |
Aerospace Series Bolts in Heat Resisting Steel, FE-PA92HT (A286) Classification: 1100 MPa/650 Degrees C Technical Specification-Issue P 1 |
|
AECMA PREN 3692 |
Aerospace Series Pipe Couplings, 37 Degree, Spherical, in Heat Resisting Steel Swivel Nuts Inch Series |
|
AECMA PREN 3693 |
Aerospace Series Pipe Couplings, 37 Degree, Spherical, in Heat Resisting Steel Straight Fittings, Welded Inch Series |
|
AECMA PREN 3696 |
Aerospace Series Washers in Heat Resisting Steel-Edition P 1 |
|
AECMA PREN 3700 |
Aerospace Series Static Inverters for Aircraft Technical Specification-Edition P 1; Corrigendum |
|
AECMA PREN 3703 |
Aerospace Series Heat Release Rate for Materials and Products under the Influence of Radiating Heat and Flames Test Method-Edition P 1 |
|
AECMA PREN 3706 |
Aerospace Series Headless Threaded Plugs, Cross Recess, in Aluminium Alloy 5086-Issue P 1 |
|
AECMA PREN 3708-003 |
Aerospace Series Modular Interconnection Systems Terminal Junction Systems Part 003 : Removable Feedback Modules Version, Sealed Product Standard-Edition P 2 |
|
AECMA PREN 3708-005 |
Aerospace Series Modular Interconnection Systems Terminal Junction Systems Part 005 : Frames with Accessories for Feedback Modules Version, Sealed and Unsealed Product Standard-Edition P 2 |
|
AECMA PREN 3711 |
Aerospace Series Wrench-Double Ended, Bi-Hexagonal Straight, Cranked, Offset-Issue P 1 |
|
AECMA PREN 3716-006 |
Aerospace Series Connectors, Single-Way, with Triaxial Interface, for Transmission of Digital Data Part 006: Crimp Plug Product Standard-Edition P 1 |
|
AECMA PREN 3718 |
Aerospace Series Test Method for Metallic Materials Ultrasonic Inspection of Tubes-Edition P 1 |
|
AECMA PREN 3726 |
Aerospace Series Nuts, Self-Locking, Clip, in Heat Resisting Steel FE-PA92HT (A286), MoS2 Coated Classification: 1 100 MPa (at Ambient Temperature)/425 Degrees C-Edition P 1 |
|
AECMA PREN 3733-101 |
Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 °C continuous Part 101: Protective cover receptacle Product standard-Edition P 1 |
|
AECMA PREN 3733-103 |
Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 °C continuous Part 103: Protective cover jam nut receptacle Product standard-Edition P 1 |
|
AECMA PREN 3733-105 |
Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 °C continuous Part 105: Receptacle connector dummy two holes fixing Product standard-Edition P 1 |
|
AECMA PREN 3743 |
Aerospace Series Straight Pins, Spring Type, Heavy Duty, in Corrosion Resisting Spring Steel, Passivated-Issue P 1 |
|
AECMA PREN 3745-509 |
Aerospace Series Fibres and Cables, Optical, Aircraft Use Test Methods Part 509 : Kink Test-Edition P 1 |
|
AECMA PREN 3746 |
Aerospace Series O-Rings, in Fluorosilicone Rubber (FVMQ) Hardness 80 IRHD-Edition P 1 |
|
AECMA PREN 3760 |
Aerospace Series Screws, 100 Degrees Countersunk Normal Head, Offset Cruciform Recess, Threaded to Head, in Heat and Corrosion Resisting Steel, Passivated Classification : 1 100 MPa (at Ambient Temperature) / 425 Degrees C-Edition P 1 |
|
AECMA PREN 3763 |
Aerospace Series Nuts, Hexagonal, Self-Locking, Ball Seat, in Heat Resisting Steel, MoS2 Lubricated Classification : 900 MPa (at Ambient Temperature) / 315 Degrees C-Edition P2 |
|
AECMA PREN 3764 |
Aerospace Series Washers, Concave, in Heat Resisting Steel, Passivated-Edition P2 |
|
AECMA PREN 3765 |
Aerospace Series Electrolytic Silver Plating for General Use Steels, Heat Resisting Alloys, Copper and Copper Alloys-Edition P1 |
|
AECMA PREN 3766 |
Aerospace Series Rivets, Blind, Nut Plate, Universal Head, in Heat Resisting Steel, Passivated, Metric Series-Edition P 1 |
|
AECMA PREN 3767 |
Aerospace Series Rivets, Blind, Nut Plate, 100 Degree Countersunk Head, in Heat Resisting Steel, Passivated, Metric Series-Edition P 1 |
|
AECMA PREN 3776 |
Aerospace Series Pins, Quick Release, Two Balls, Single Acting, Single Locking, |
|
AECMA PREN 3783 |
Aerospace Series Fibre Composite Materials Normalisation of Fibre Dominated Mechanical Properties-Issue P 1 |
|
AECMA PREN 3786 |
Aerospace Series Pipe Couplings, 37 Degree, Spherical, in Heat Resisting Steel Tees with Fitting, Welded Inch Series |
|
AECMA PREN 3813 |
Aerospace Series Titanium Alloy TI-P64001 Annealed Bar and Wire for Forged Fasteners De Less Than or Equal to 25 mm-Edition P1 |
|
AECMA PREN 3813 |
Aerospace Series Titanium Alloy Ti-P64001 Annealed Bar and Wire for Forged Fasteners De Less Than or Equal to 25 mm-Edition P1 |
|
AECMA PREN 3821 |
Aerospace Series Washers, Chamfered, with Counterbore, in Heat Resisting Steel, Passivated-Edition P 2 |
|
AECMA PREN 3822 |
Aerospace Series Washers, Flat, Thick, in Heat Resisting Steel, Passivated-Edition P 1 |
|
AECMA PREN 3822 |
Aerospace Series Washers, Flat, Thick, in Heat Resisting Steel, Passivated-Edition P 2 |
|
AECMA PREN 3830 |
Aerospace Series Electrical System Load Analysis-Edition P 1 |
|
AECMA PREN 3831 |
Aerospace Series Inserts, Thick Wall, Self-Locking, in Heat Resisting Steel FE-PM3801 (17-4PH), MoS2 Coated-Edition P 2 |
|
AECMA PREN 3835 |
Aerospace Series Washers, 100 Degrees Dimpled, in Heat Resisting Steel, Passivated-Edition P 1 |
|
AECMA PREN 3840 |
Aerospace Series Paints and Varnishes Technical Specification-Edition P 2 |
|
AECMA PREN 3841-301 |
Aerospace Series Circuit Breakers Test Methods Part 301 : Voltage Drop-Edition P 1 |
|
AECMA PREN 3841-301 |
Aerospace Series Circuit Breakers Test Methods Part 301 : Voltage Drop-Edition P 2 |
|
AECMA PREN 3841-302 |
Aerospace Series Circuit Breakers Test Methods Part 302 : Insulation Resistance-Edition P 2 |
|
AECMA PREN 3841-303 |
Aerospace Series Circuit Breakers Test Methods Part 303 : Dielectric Strength-Edition P 1 |
|
AECMA PREN 3841-303 |
Aerospace Series Circuit Breakers Test Methods Part 303 : Dielectric Strength-Edition P 2 |
|
AECMA PREN 3841-402 |
Aerospace Series Circuit Breakers Environmental Test Methods Corrosion Test |
|
AECMA PREN 3841-502 |
Aerospace Series Circuit Breakers Test Methods Part 502 : Operating Forces-Edition P 1 |
|
AECMA PREN 3846 |
Aerospace Series Honeycomb Cores, Polyamide Paper, Phenolic Resin Impregnated Technical Specification |
|
AECMA PREN 3848 |
Aerospace Series Semi-Finished Metallic Products Methods of Measuring from Deviations-Edition P2 |
|
AECMA PREN 3854 |
Aerospace Series Pipe Couplings, 60 Degrees, Spherical, in Titanium Alloy TI-P64001 Ferrules, Welded-Edition P1 |
|
AECMA PREN 3874 |
Aerospace Series Test Methods for Metallic Materials Constant Amplitude Force-Controlled Low Cycle Fatigue Testing |
|
AECMA PREN 3874 |
Aerospace Series Test Methods for Metallic Materials Constant Amplitude Force-Controlled Low Cycle Fatigue Testing-Edition P 1 |
|
AECMA PREN 3875 |
Aerospace Series Metallic Materials Filler Metal for Brazing Technical Specification-Edition P 1 |
|
AECMA PREN 3902 |
Aerospace Series Washers for Rivet Assemblies, in Aluminium Alloy, Anodized, Metric Series-Edition P1 |
|
AECMA PREN 3904 |
Aerospace Series Washers, Wire Locking, in Aluminium Alloy, Anodized-Edition P1 |
|
AECMA PREN 3908 |
Aerospace Series Nipples, Lubricating, Axial Type, in Corrosion Resisting Steel, Passivated-Edition P 1 |
|
AECMA PREN 3908 |
Aerospace Series Nipples, Lubricating, Axial Type, in Corrosion Resisting Steel, Passivated-Edition P 2 |
|
AECMA PREN 3910-001 |
Aerospace Series High Speed Data Transmission Under STANAG 3838 or Fibre Optic Equivalent Control-Edition P 1 |
|
AECMA PREN 3911 |
Aerospace Series Six Lobe Recess Geometrical Definition-Edition P 1 |
|
AECMA PREN 3912 |
Aerospace Series Bolts, Pan Head, Six Lobe Recess, Relieved Shank, Long Thread, in Heat Resisting Steel FE-PA92HT (A286), Silver Plated Classification: 1 100 MPa (at Ambient Temperature)/650 Degrees C-Edition P 1 |
|
AECMA PREN 3957 |
Aerospace Series Silver Base Alloy AG-B14001 Filler Metal for Brazing Powder or Paste-Edition P 3; Supersedes Edition P 2: May 1995; Replaced by EN 3957 |
|
AECMA PREN 3979 |
Aerospace Series Aluminium Alloy AL-P8090-O2 Sheet for Superplastic Forming (SPF) 0,8 mm Less Than or Equal to a Less Than or Equal to 6 mm-Edition P 1 |
|
AECMA PREN 3997 |
Aerospace Series Aluminium Alloy AL-P2024-T3 Sheet and Strip 0,4 mm Less Than or Equal to a Less Than or Equal to 6 mm-Edition P1 |
|
AECMA PREN 3999 |
Aerospace Series Aluminium Alloy AL-P2024-T351 Sheet and Strip with Improved Chemical Milling Capability 1,6 mm Less Than or Equal to a Less Than or Equal to 6 mm-Edition P 2 |
|
AECMA PREN 4001 |
Aerospace Series Aluminium Alloy AL-P2024-T351 Clad Sheet and Strip with Improved Chemical Milling Capability 1,6 mm Less Than or Equal to a Less Than or Equal 6 mm-Edition P 2 |
|
AECMA PREN 4004 |
Aerospace Series Aluminium Alloy AL-P3103-H16 Sheet and Strip 0,4 mm Less Than or Equal to a Less Than or Equal to 6 mm-Edition P 2 |
|
AECMA PREN 4008-007 |
Aerospace Series Elements of Electrical and Optical Connection Crimping Tools and Associated Accessories Part 007: Positioner for Crimping Tool M22520/2-01 Product Standard-Edition P 1 |
|
AECMA PREN 4008-012 |
Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 012: Positioner for crimping tool M22520/2-01 Product standard-Edition P 1 |
|
AECMA PREN 4008-017 |
Aerospace series Elements of electrical and optical connection Crimping tool and associated accessories Part 017: Head for crimping tool M22520/4-01 Product standard-Edition P 1 |
|
AECMA PREN 4016 |
Aerospace Series Oversized Bolts-Edition P 1 |
|
AECMA PREN 4018 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Elbows 90 Degrees, Swivel Nut-Edition P1 |
|
AECMA PREN 4020 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Elbows 90 Degrees Swivel Nut, Welded-Edition P1 |
|
AECMA PREN 4034 |
Aerospace Series Bearings, Airframe Rolling Double Row Self- Aligning Ball Bearings with Flanged Outer Ring in Corrosion Resisting Steel, Reduced Internal Radial Clearance Dimensions and Loads-Edition P 1 |
|
AECMA PREN 4049-004 |
Aerospace Series Thermocouple Extension Cable Operating Temperatures between -65 Degrees C and 260 Degrees C Part 004: Two Core Nickel Chromium/Nickel Aluminium Shielded and Jacketed Product Standard |
|
AECMA PREN 4056-001 |
Aerospace Series Cable Ties for Harnesses Part 001: Technical Specification-Edition P 1 |
|
AECMA PREN 4056-002 |
Aerospace Series Cable Ties for Harnesses Part 002: Index of Product Standards-Edition 4 |
|
AECMA PREN 4056-002 |
Aerospace Series Cable Ties for Harnesses Part 002: Index of Product Standards-Edition P 1 |
|
AECMA PREN 4056-003 |
Aerospace Series Cable Ties for Harnesses Part 003: Plastic Cable Ties, Operating Temperatures - 65 Degrees C to 105 Degrees C and - 65 Degrees C to 150 Degrees C Product Standard-Edition P 1 |
|
AECMA PREN 4057-100 |
Aerospace Series Cable Ties for Harnesses Test Methods Part 100: General-Edition P 1 |
|
AECMA PREN 4057-201 |
Aerospace Series Cable Ties for Harnesses Test Methods Part 201: Visual Examination-Edition P 1 |
|
AECMA PREN 4057-202 |
Aerospace Series Cable Ties for Harnesses Test Methods Part 202: Examination of Mass and Dimensions-Edition P 1 |
|
AECMA PREN 4073 |
Aerospace Series Screws, Pan Head, Six Lobe Recess, Coarse Tolerance Normal Shank, Medium Length Thread, in Alloy Steel, Cadmium Plated Classification : 1 100 MPa (at Ambient Temperature)/235 Degrees C-Edition P1 |
|
AECMA PREN 4074 |
Aerospace Series Screws, Pan Head, Six Lobe Recess, Coarse Tolerance Normal Shank, Medium Length Thread, in Titanium Alloy, Aluminium IVD Coated Classification : 1 100 MPa (at Ambient Temperature)/ 425 Degrees C-Edition P1 |
|
AECMA PREN 4079 |
Aerospace Series Screws, 100 Degree Countersunk Normal Head, Offset Cruciform Recess, Threaded to Head, in Alloy Steel, Cadmium Plated Classification: 900 MPa (at Ambient Temperature)/235 Degrees C-Edition P1 |
|
AECMA PREN 4108 |
Aerospace Series Wrenches, Crow Foot, Attachment Socket, Socket Drive-Edition P1 |
|
AECMA PREN 4109 |
Aerospace Series Wrenches, Face Spanner-Edition P1 |
|
AECMA PREN 4110 |
Aerospace Series Wrenches, Open End, Box-Edition P 1 |
|
AECMA PREN 4111 |
Aerospace Series Wrenches, Splined, Sockets for Pipe Fittings Technical Specification-Edition P 2 |
|
AECMA PREN 4114 |
Aerospace Series Clamps, Loop ( |
|
AECMA PREN 4115 |
Aerospace Series Cushion, Rubber for Clamps Dimensions, Massess-Edition P 1 |
|
AECMA PREN 4129 |
Aerospace Series Bolts, Normal Hexagonal Head, Coarse Tolerance Normal Shank, Medium Length Thread, in Alloy Steel, Cadmium Plated Classification : 1 100 MPa (at Ambient Temperature)/235 Degrees C-Edition P1 |
|
AECMA PREN 4130 |
Aerospace Series Bolts, Normal Hexagonal Head, Coarse Tolerance Normal Shank, Medium Length Thread, in Titanium Alloy, Aluminium IVD Coated Classification : 1 100 MPa (at Ambient Temperature)/450 Degrees C-Edition P1 |
|
AECMA PREN 4150 |
Aerospace Series Pipe Couplings 60 Degree; in Anodized Aluminium Alloy ; Nuts, Bulkhead |
|
AECMA PREN 4153 |
Aerospace Series Rivets, Solid, Universal Head, in Aluminium Alloy 2219, Anodized or Chromated, Metric Series-Edition P 1 |
|
AECMA PREN 4154 |
Aerospace Series Rivets, Solid, 100 Degree Normal Countersunk Head, in Aluminium Alloy 2219, Anodized or Chromated, Metric Series-Edition P1 |
|
AECMA PREN 4158 |
Aerospace series Paints and varnishes Test method for measurements of electrical surface resistance of conductive layers-Edition P 1 |
|
AECMA PREN 4160 |
Aerospace Series Paints and Varnishes Determination of the Effect of Thermal Exposure |
|
AECMA PREN 4162 |
Aerospace Series Screws, 100 Degrees Countersunk Normal Head, Offset Cruciform Recess, Coarse Tolerance Normal Shank, Medium Length Thread, in Alloy Steel, Cadmium Plated Classification : 1 100 MPa (at Ambient Temperature) / 235 Degrees Celsius-Edition P1; Supersedes C3 N |
|
AECMA PREN 4164 |
Aerospace Series Screws, 100 Degrees Countersunk Normal Head, Offset Cruciform Recess, Threaded to Head, in Alloy Steel, Cadmium Plated Classification : 1 100 MPa (at Ambient Temperature) / 235 Degrees Celsius-Edition P1; Supersedes C3 N |
|
AECMA PREN 4164 |
Aerospace Series Screws, 100 Degrees Countersunk Normal Head, Offset Cruciform Recess, Threaded to Head, in Alloy Steel, Cadmium Plated Classification : 1 100 MPa (at Ambient Temperature)/235 Degrees C-Edition P1 |
|
AECMA PREN 4165-003 |
Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 °C continuous Part 003: Modules series 2 and series 3 Product standard-Edition P 2;:2001 Edition P 1 |
|
AECMA PREN 4165-005 |
Aerospace Series Connectors, Electrical, Rectangular, Modular Operating Temperature 175 Degrees C Continuous Part 005: Stackable Mounting Receptacle 2 and 4 Modules Series 3-Edition P 1 |
|
AECMA PREN 4165-008 |
Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 Degrees C continuous Part 008: Rack and panel plug for 2 and 4 modules, series 2 Product standard-Edition P 1 |
|
AECMA PREN 4165-010 |
Aerospace Series Connectors, Electrical, Rectangular, Modular Operating Temperature 175 Degrees Celsius Continuous Part 010: Rack and Panel Mounted Plug 2 and 4 Modules, Series 2 Product Standard-Edition 1E |
|
AECMA PREN 4165-019 |
Aerospace Series Connectors, Electrical, Rectangular, Modular Operating Temperature 175 Degrees Celsius Continuous Part 019: Protective Cover for Plug, for 2 or 4 Modules Series 2 and Series 3 Product Standard-Edition 1E |
|
AECMA PREN 4165-021 |
Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 Degrees C continuous Part 021: Coupling system keyway for plug Product standard-Edition P 1 |
|
AECMA PREN 4165-023 |
Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 Degrees C continuous Part 023: Tooling for assembly of receptacle coding component Product standard-Edition P 1 |
|
AECMA PREN 4166 |
Aerospace Series Busching in PTFE for Clips Spring Tension-Edition P1 |
|
AECMA PREN 4167 |
Aerospace Series Clips, Spring Tension, Three Parts Inner Clips in Heat Resisting Steel FE-PA92HT (A286)-Edition P1 |
|
AECMA PREN 4179 |
Aerospace Series Qualification and Approval of Personnel for Non-Destructive Testing-Edition P 2; Supersedes Edition P 1: January 1995; Replaced by EN 4179 |
|
AECMA PREN 4187 |
Aerospace Series Pipe Coupling 8 Degrees 30' in Titanium Alloy Elbows 90 Degrees, Bulkhead, Long-Edition P 1 |
|
AECMA PREN 4199-004 |
Aerospace Series Bonding Straps for Aircraft, Part 004: Round Bonding Straps, Copper, Tin Plated, -65 Degrees C up to + 150 Degrees C, and Nickel Plated, -65 Degrees C up to 260 Degrees C Product Standard-Edition P 1 |
|
AECMA PREN 4219 |
Aerospace Series Nuts, Hexagon, Self-Locking by Domed Plastic Cap, Normal Height, Normal Across Flats, in Corrosion Resisting Steel, Passivated Classification : 900 MPa (at Ambient Temperature) / 120 Degrees Celsius-Edition P 1 |
|
AECMA PREN 4219 |
Aerospace Series Nuts, Hexagon, Self-Locking by Domed Plastic Cap, Normal Height, Normal Across Flats, in Corrosion Resisting Steel, Passivated Classification : 900 MPa (at Ambient Temperature) / 120 Degrees Celsius-Edition P1; Superseding C 3/ WG 5 N 236 |
|
AECMA PREN 4225 |
Aerospace Series Pipe Couplings, 60 Degree; in Anodized Aluminium Alloy Plugs for Taper Union |
|
AECMA PREN 4234 |
Aerospace Series Clamps, Worm Drive Dimensions, Massess-Edition P 2 |
|
AECMA PREN 4235-1 |
Aerospace Series Steel Wrought Products Technical Specification Part 1: General Requirements-Edition P 1 |
|
AECMA PREN 4235-4 |
Aerospace Series Steel Wrought Products Technical Specification Part 4: Tube-Edition P 1 |
|
AECMA PREN 4235-5 |
Aerospace Series Steel Wrought Products Technical Specification Part 5: Wire-Edition P 2 |
|
AECMA PREN 4260 |
Aerospace Series Metallic Materials Rules for Drafting and Presentation of Technical Specifications-Edition P 1 |
|
AECMA PREN 4266 |
Aerospace Series Bearings, Spherical Plain, in Corrosion Resisting Steel, Cadmium Plated Wide Series - Dimensions and Loads Inch Series-Edition P 1 |
|
AECMA PREN 4293 |
Aerospace Series Aluminium Alloy AL-P7175-T73511 Extruded Bar and Section a or D Less Than or Equal to 150 mm-Edition P1 |
|
AECMA PREN 4300 |
Aerospace Series Identification Marking of Engine Items Design Standard-Edition P 1 |
|
AECMA PREN 4300 |
Aerospace Series Identification Marking of Engine Items Design Standard-Edition P1 |
|
AECMA PREN 4301 |
Aerospace Series Identification Marking Methods for Engine Items Engineering Requirements-Edition P 1 |
|
AECMA PREN 4311 |
Aerospace Series Studs, Coarse Tolerance Reduced Shank, Medium Length Threads, in Heat and Corrosion Resisting Steel, MoS2 Lubricated Classification : 1 100 MPa (at Ambient Temperature) / 315 Degrees Celsius-Edition P 1 |
|
AECMA PREN 4312 |
Aerospace Series Studs, Close Tolerance Shank, Medium Length Thread, in Heat and Corrosion Resisting Steel, Aluminium Pigmented Organic Coating, Classification : 1100 MPa (at Ambient Temperature) / 425 Degrees Celsius-Edition P1 |
|
AECMA PREN 4317 |
Aerospace Series Heat Resisting Alloy FE-PA2601 (X6NiCrTiMoV26-15) Non Heat Treated Forging Stock a or D Less Than or Equal to 200mm-Edition P 1 |
|
AECMA PREN 4323 |
Aerospace Series Screws, 100 Degree Countersunk Head, Six Lobe Recess, Threaded to Head, in Titanium Alloy TI-P63, Anodized, MoS2 Coated Classification: 900 MPa (at Ambient Temperature)/ 350 Degrees C-Edition P1 |