|
CEN EN 14757 |
Water quality - Sampling of fish with multi-mesh gillnets |
|
CEN EN 14782 |
Self-supporting metal sheet for roofing, external cladding and internal lining - Product specification and requirements |
|
CEN EN 14809 |
Surfaces for sports areas - Determination of vertical deformation-Incorporating corrigendum October 2007 |
|
CEN EN 1482-2 |
Fertilizers and liming materials - Sampling and sample preparation - Part 2: Sample preparation |
|
CEN EN 14830 |
Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance |
|
CEN EN 14840 |
Joint fillers and sealants - Test methods for preformed joint seals |
|
CEN EN 14877 |
Synthetic surfaces for outdoor sports areas - Specification |
|
CEN EN 14891 |
Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements, test methods, evaluation of conformity, classification and designation |
|
CEN EN 14897 |
Water conditioning equipment inside buildings - Devices using mercury low-pressure ultraviolet radiators - Requirements for performance, safety and testing-Incorporates Amendment A1: June 2007 |
|
CEN EN 14916 |
Domestic cookware - Graphical symbols (pictograms) |
|
CEN EN 14944-3 |
Influence of cementitious products on water intended for human consumption - Test methods - Part 3: Migration of substances from factory-made cementititous products |
|
CEN EN 14978 |
Laminate floor coverings - Elements with acrylic based surface layer, electron beam cured - Specifications, requirements and test methods |
|
CEN EN 15034 |
Heating boilers - Condensing heating boilers for fuel oil |
|
CEN EN 1503-4 |
Valves - Materials for Bodies, Bonnets and Covers - Part 4: Copper Alloys Specified in European Standards |
|
CEN EN 1504-7 |
Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 7: Reinforcement corrosion protection |
|
CEN EN 1505 |
Ventilation for Buildings - Sheet Metal Air Ducts and Fittings with Rectangular Cross-Section - Dimensions |
|
CEN EN 15091 |
Sanitary tapware - Electronic opening and closing sanitary tapware-Incorporating corrigendum October 2007 |
|
CEN EN 15167-2 |
Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 2: Conformity evaluation |
|
CEN EN 15200 |
Sanitary appliances - Multifunction shower cabinets |
|
CEN EN 1522 |
Windows, Doors, Shutters and Blinds - Bullet Resistance - Requirements and Classification-Ratified European Text |
|
CEN EN 15221-2 |
Facility Management - Part 2: Guidance on how to prepare Facility Management agreements |
|
CEN EN 1523 |
Windows, Doors, Shutters and Blinds - Bullet Resistance - Test Method-Ratified European Text |
|
CEN EN 15238 |
Soil improvers and growing media - Determination of quantity for materials with particle size greater than 60 mm |
|
CEN EN 15255 |
Energy performance of buildings - Sensible room cooling load calculation - General criteria and validation procedures |
|
CEN EN 1529 |
Doors Leaves - Height, Width, Thickness and Squareness - Tolerance Classes |
|
CEN EN 15312 |
Free access multi-sports equipment - Requirements, including safety, and test methods |
|
CEN EN 15360 |
Fertilizers - Determination of dicyandiamide - Method using high-performance liquid chromatography (HPLC) |
|
CEN EN 15377-3 |
Heating systems in buildings - Design of embedded water based surface heating and cooling systems - Part 3: Optimizing for use of renewable energy sources |
|
CEN EN 1604 |
Thermal Insulating Products for Building Applications - Determination of Dimensional Stability under Specified Temperature and Humidity Conditions-Incorporating Corrigendum and Amendment A1:2006 |
|
CEN EN 1605 |
Thermal Insulating Products for Building Applications - Determination of Deformation Under Specified Compressive Load and Temperature Conditions-Incorporating Corrigendum; Incorporating A1:2006 |
|
CEN EN 1606 |
Thermal Insulating Products for Building Applications - Determination of Compressive Creep-Incorporating Corrigendum; Amendment A1: 2006 |
|
CEN EN 1607 |
Thermal Insulating Products for Building Applications - Determination of Tensile Strength Perpendicular to Faces-Incorporating Corrigendum |
|
CEN EN 1730 |
Domestic Furniture - Tables - Test Methods for Determination of Strength, Durability and Stability |
|
CEN EN 1738 |
Determination of Steel Stresses in Unloaded Reinforced Components Made of Autoclaved Aerated Concrete |
|
CEN EN 1739 |
Determination of shear strength for in-plane forces of joints between prefabricated components of autoclaved aerated concrete or lightweight aggregate concrete with open structure |
|
CEN EN 1742 |
Determination of Shear Strength between Different Layers of Multilayer Components Made of Autoclaved Aerated Concrete or Lightweight Aggregate Concrete with Open Structure |
|
CEN EN 1771 |
Products and systems for the protection and repair of concrete structures Test methods Determination of injectability and splitting test |
|
CEN EN 178 |
Dust-Pressed Ceramic Tiles with a Water Absorption of 6% |
|
CEN EN 1804-3 |
Machines for underground mines Safety requirements for hydraulic powered roof supports Part 3: Hydraulic control systems |
|
CEN EN 1809 |
Diving Accessories - Buoyancy Compensators - Functional and Safety Requirements, Test Methods |
|
CEN EN 1824 |
Road Marking Materials - Road Trials |
|
CEN EN 1844 |
Flexible Sheets for Waterprofing - Determination of Resistance to Ozone - Plastic and Rubber Sheets for Roof Waterprofing |
|
CEN EN 1848-1 |
Flexible Sheets for Waterproofing - Determination of Length, Width and Straightness - Part 1: Bitumen Sheets for Roof Waterproofing |
|
CEN EN 1848-2 |
Flexible Sheets for Waterproofing - Determination of Length, Width, Straightness and Flatness - Part 2: Plastic and Rubber Sheets for Roof Waterproofing |
|
CEN EN 1849-2 |
Flexible Sheets for Waterproofing - Determination of Thickness and Mass Per Unit Area - Part 2: Plastic and Rubber Sheets for Roof Waterproofing |
|
CEN EN 1853 |
Agricultural Machinery - Trailers with Tipping Body - Safety |
|
CEN EN 1857 |
Chimneys - Components - Concrete flue liners-Incorporating corrigendum April 2007 |
|
CEN EN 1858 |
Chimneys - Components - Concrete flue blocks |
|
CEN EN 187-1 |
Ceramic Tiles - Extruded Ceramic Tiles with a Water Absorption of 6% |
|
CEN EN 1929-1 |
Basket Trolleys - Part 1: Requirements and Tests for Basket Trolleys with or without a Child Carrying Facility |
|
CEN EN 1929-4 |
Basket trolleys - Part 4: Requirements and tests for basket trolleys with additional goods carrying facility(ies), with or without a child carrying facility, intended to be used on passenger conveyors |
|
CEN EN 1931 |
Flexible Sheets for Waterproofing - Bitumen, Plastic and Rubber Sheets for Roof Waterproofing - Determination of Water Vapour Transmission Properties-Incorporating Corrigendum February 2001 |
|
CEN EN 1946-1 |
Thermal Performance of Building Products and Components - Specific Criteria for the Assessment of Laboratories Measuring Heat Transfer Properties - Part 1: Common Criteria |
|
CEN EN 1946-2 |
Thermal Performance of Building Products and Components - Specific Criteria for the Assessment of Laboratories Measuring Heat Transfer Properties - Part 2: Measurements by Guarded Hot Plate Method |
|
CEN EN 1969 |
Surfaces for Sports Areas - Determination of Thickness of Synthetic Sports Surfaces |
|
CEN EN 202 |
Ceramic Tiles - Determination of Frost Resistance |
|
CEN EN 203-2-7 |
Gas heated catering equipment - Part 2-7: Specific requirements - Salamanders and rotisseries |
|
CEN EN 24 |
Doors: Measurement of Defects of General Flatness of Door Leaves-Superseded |
|
CEN EN 259-1 |
Wallcoverings in Roll Form - Heavy Duty Wallcoverings - Part 1: Specifications |
|
CEN EN 274-2 |
Waste Fittings for Sanitary Appliances - Part 2: Test Methods |
|
CEN EN 274-3 |
Waste Fittings for Sanitary Appliances - Part 3: Quality Control-(Together with EN 274-1: 2002 and EN 274-2: 2002) |
|
CEN EN 28960 |
Refrigerators, Frozen- Food Storage Cabinets and Food Freezers for Household and Similar Use - Measurement of Emission of Airborne Acoustical Noise (ISO 8960 : 1991) |
|
CEN EN 29117 |
Paints and Varnishes - Determination of Through-Dry State and Through-Dry Time - Method of Test; (ISO 9117 : 1990) |
|
CEN EN 30-1-4 |
Domestic cooking appliances burning gas - Part 1-4: Safety - Appliances having one or more burners with an automatic burner control system-Incorporating Amendment A1: 2006 |
|
CEN EN 303-2 |
Heating boilers Part 2: Heating boilers with forced draught burners Special requirements for boilers with atomizing oil burners-Includes amendment A1:2003 |
|
CEN EN 303-5 |
Heating Boilers - Part 5: Heating Boilers for Solid Fuels, Hand and Automatically Stoked, Nominal Heat Output of up to 300 kW - Terminology, Requirements, Testing and Marking |
|
CEN EN 36 |
Wall-Hung Bidets with over-Rim Supply - Connecting Dimensions-Ratified European Text |
|
CEN EN 399 |
Lifejackets and Personal Buoyancy Aids - Lifejackets - 275 N-Includes Amendment A1:1998 |
|
CEN EN 40-4 |
Lighting Columns - Part 4: Surface Protection of Metal Lighting Columns |
|
CEN EN 409 |
Timber Structures - Test Methods - Determination of the Yield Moment of Dowel Type Fasteners - Nails |
|
CEN EN 42 |
Methods of Festing Windows - Part 1: Air Permeability Test |
|
CEN EN 428 |
Resilient Floor Coverings - Determination of Overall Thickness |
|
CEN EN 434 |
Resilient Floor Coverings - Determination of Dimensional Stability and Curling After Exposure to Heat |
|
CEN EN 447 |
Grout for prestressing tendons - Basic requirements |
|
CEN EN 450-1 |
Fly ash for concrete - Part 1: Definition, specifications and conformity criteria-Incorporates Amendment A1: 10/2007 |
|
CEN EN 480-2 |
Admixtures for concrete, mortar and grout - Test methods - Part 2: Determination of setting time |
|
CEN EN 480-6 |
Admixtures for concrete, mortar and grout - Test methods - Part 6: Infrared analysis |
|
CEN EN 490 |
Concrete roofing tiles and fittings for roof covering and wall cladding - Product specifications |
|
CEN EN 497 |
Specification for Dedicated Liquefied Petroleum Gas Appliances - Multi Purpose Boiling Burners for Outdoor Use |
|
CENELEC EN 50065-4-5 |
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-5: Low voltage decoupling filter - Segmentation filter |
|
CEN EN 502 |
Roofing Products from Metal Sheets - Specification for Fully Supported Roofing Products of Stainless Steel Sheet |
|
CEN EN 516 |
Prefabricated Accessories for Roofing - Installations for Roof Access - Walkways, Treads and Steps |
|
CEN EN 538 |
Clay Roofing Tiles for Discontinuous Laying - Flexural Strength Test |
|
CEN EN 596 |
Timber Structures - Test Methods - Soft Body Impact Test of Timber Framed Walls |
|
CENELEC EN 60661/A1 |
Methods for measuring the performance of electrical household coffee makers-IEC 60661:1999/A1:2003; Amendment A1; Ratified European Text |
|
CENELEC EN 60674-3-1 |
Plastic Films for Electrical Purposes Part 3: Specifications for Individual Materials Sheet 1: Biaxially Oriented Polypropylene (PP) Film for Capacitors-IEC 60674-3-1: 1998 |
|
CENELEC EN 60674-3-2 |
Specification for Plastic Films for Electrical Purposes Part 3: Specifications for Individual Materials Sheet 2: Requirements for Balanced Biaxially Oriented Polyethylene Terephthalate (PET) Films Used for Electrical Insulation-IEC 60674-3-2:1992 |
|
CENELEC EN 60704-2-9 |
Household and similar electrical appliances - Test code for the determination of airborne acoustical noise Part 2-9: Particular requirements for electric hair care appliances-IEC 60704-2-9: 2003 |
|
CENELEC EN 60730-2-16 |
Automatic electrical controls for household and similar use - Part 2-16: Particular requirements for automatic electrical water level controls of the float type for household and similar applications-Includes Amendments A1: 1998; Amendment A2: 2001; Amendment A11: 2005; Incorporating Corrigendum May 2000 |
|
CENELEC EN 61030 |
Audio, Video and Audiovisual Systems Domestic Digital Bus (D2B) (IEC 1030:1991 + A1:1993) |
|
CENELEC EN 61228 |
Method of Measuring and Specifying the UV-Radiation of Ultraviolet Lamps Used for Sun-Tanning-Includes Amendment A1: 1996; IEC 1228: 1993 + A1: 1996 |
|
CEN EN 62054-21 |
Electricity metering (a.c.) - Tariff and load control Part 21: Particular requirements for time switches |
|
CEN EN 679 |
Determination of the compressive strength of autoclaved aerated concrete |
|
CEN EN 680 |
Determination of the drying shrinkage of autoclaved aerated concrete |
|
CEN EN 684 |
Resilient Floor Coverings - Determination of Seam Strength |
|
CEN EN 695 |
Kitchen Sinks - Connecting Dimensions |
|
CEN EN 707 |
Agricultural Machinery - Slurry Tankers - Safety |
|
CEN EN 708 |
Agricultural Machinery - Soil Working Machines with Powered Tools - Safety-Includes Amendment A1:2000 |
|
CEN EN 771-4 |
Specification for masonry units Part 4: Autoclaved aerated concrete masonry units-Includes amendment A1:2005 |
|
CEN EN 772-4 |
Methods of Test for Masonry Units - Part 4: Determination of Real and Bulk Density and of Total and Open Porosity for Natural Stone Masonry Units |
|
CEN EN 772-9 |
Methods of Test for Masonry Units - Part 9: Determination of Volume and Percentage of Voids and Net Volume of Calcium Silicate Masonry Units by Sand Filling |
|
CEN EN 80 |
Wall Hung Urinals - Connecting Dimensions |
|
CEN EN 825 |
Thermal Insulating Products for Building Applications - Determination of Flatness |
|
CEN EN 845-2 |
Specification for ancillary components for masonry - Part 2: Lintels |
|
CEN EN 846-10 |
Methods of Test for Ancillary Components for Masonry - Part 10: Determination of Load Capacity and Load Deflection Characteristics of Brackets |
|
CEN EN 846-7 |
Methods of Test for Ancillary Components for Masonry - Part 7: Determination of Shear Load Capacity and Load Displacement Characteristics of Shear Ties and Slip Ties (Couplet Test for Mortar Joint Connections) |
|
CEN EN 87 |
Ceramic Floor and Wall Tiles - Definitions, Classification, Characteristics and Marking |
|
CEN EN 908 |
Agricultural and Foresty Machinery - Reel Machines for Irrigation - Safety-Ratified European Text |
|
CEN EN 916 |
Gymnastic equipment - Vaulting boxes - Requirements and test methods including safety |
|
CEN EN 926-2 |
Paragliding equipment - Paragliders - Part 2: Requirements and test methods for classifying flight safety characteristics-Supersedes ENV 926-2:1999 |
|
CEN EN 927-4 |
Paints and Vanishes - Coating Materials and Coating Systems for Exterior Wood - Part 4: Assessment of the Water-Vapuor Permeability |
|
CEN EN 932-6 |
Tests for General Properties of Aggregates - Part 6: Definitions of Repeatability and Reproducibility |
|
CEN EN 933-10 |
Tests for Geometrical Properties of Aggregates - Part 10: Assessment of Fines - Grading of Fillers (Air Jet Sieving) |
|
CEN EN 933-5 |
Tests for Geometrical Properties of Aggregates - Part 5: Determination of Percentage of Crushed and Broken Surfaces in Coarse Aggregate Particles-Includes Amendment A1:2004 |
|
CEN EN 933-8 |
Tests for Geometrical Properties of Aggregates - Part 8: Assessment of Fines - Sand Equivalent Test |
|
CEN EN 951 |
Door Leaves - Method for Measurement of Height, Width, Thickness and Squareness-Supersedes EN 25:1975 |
|
CEN EN 952 |
Door Leaves - General and Local Flatness - Measurement Method-Supersedes EN 24: 1974 |
|
CEN EN 997 |
WC pans and WC suites with integral trap-Incorporating Amendment 1: 12/2006 |
|
CEN EN ISO 10249 |
Fluid Fertilizers - Preliminary Visual Examination and Preparation of Samples for Physical Testing-ISO 10249:1996 |
|
CEN EN ISO 10545-15 |
Ceramic Tiles - Part 15: Determination of Lead and Cadmium Given off by Glazed Tiles-ISO 10545-15: 1995 |
|
CEN EN ISO 10545-16 |
Ceramic Tiles - Part 16: Determination of Small Colour Differences-ISO 10545-16:1999 |
|
CEN EN ISO 10545-2 |
Ceramic Tiles - Part 2: Determination of Dimensions and Surface Quality-Supersedes EN 98: 1991 |
|
CEN EN ISO 11125-3 |
Preparation of Steel Substrates before Application of Paints and Related Products - Test Methods for Metallic Blast-Cleaning Abrasives - Part 3: Determination of Hardness-ISO 11125-3: 1993 |
|
CEN EN ISO 11126-3 |
Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 3: Copper refinery slag-ISO 11126-3: 1993 |
|
CEN EN ISO 11126-4 |
Preparation of Steel Substrates Before Application of Paints and Related Products - Specifications for Non-Metallic Blast- Cleaning Abrasives - Part 4: Coal Furnance Slag-ISO 11126-4: 1993 |
|
CEN EN ISO 11126-8 |
Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 8: Olivine sand-ISO 11126-8: 1993 |
|
CEN EN ISO 11127-7 |
Preparation of Steel Substrates Before Application of Paints and Related Products - Test Methods for Non-Metallic Blast-Cleaning Abrasives - Part 7: Determination of Water-Soluble Chlorides-ISO 11127-7: 1993 |
|
CEN EN ISO 11341 |
Paints and varnishes - Artificial weathering and exposure to artificial radiation - Exposure to filtered xenon-arc radiation-ISO 11341:2004 |
|
CEN EN ISO 11432 |
Building Construction - Sealants - Determination of Resistance to Compression-ISO 11432: 2005 |
|
CEN EN ISO 11890-1 |
Paints and Varnishes - Determination of Volatile Organic Compound (VOC) Content - Part 1: Difference Method-ISO 11890-1:2000 |
|
CEN EN ISO 12567-2 |
Thermal performance of windows and doors - Determination of thermal transmittance by hot box method - Part 2: Roof windows and other projecting windows-ISO 12567-2:2005 |
|
CEN EN ISO 12571 |
Hygrothermal Performance of Building Materials and Products - Determination of Hygroscopic Sorption Properties-ISO 12571:2000 |
|
CEN EN ISO 13789 |
Thermal Performance of Buildings - Transmission Heat Loss Coefficient - Calculation method-ISO 13789:1999 |
|
CEN EN ISO 140-11 |
Acoustics - Measurement of sound insulation in buildings and of building elements - Part 11: Laboratory measurements of the reduction of transmitted impact sound by floor coverings on lightweight reference floors-ISO 140-11:2005 |
|
CEN EN ISO 140-12 |
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 12: Laboratory Measurement of Room-To-Room Airborne and Impact Sound Insulation of an Access Floor-ISO 140-12: 2000 |
|
CEN EN ISO 140-5 |
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 5: Field Measurements of Airborne Sound Insulation of Facade Elements and Facades-ISO 140-5:1998 |
|
CEN EN ISO 140-6 |
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 6: Laboratory Measurements of Impact Sound Insulation of Floors-ISO 140-6:1998 |
|
CEN EN ISO 140-7 |
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 7: Field Measurements of Impact Sound Insulation of Floors-ISO 140-7:1998 |
|
CEN EN ISO 140-8 |
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 8: Laboratory Measurements of the Reduction of Transmitted Impact Noise by Floor Coverings on a Heavyweight Standard Floor-ISO 140-8: 1997 |
|
CEN EN ISO 14565 |
Animal Feeding Stuffs - Determination of Vitamin A Content - Method Using High-Performance Liquid Chromatography-ISO 14565:2000 |
|
CEN EN ISO 14680-2 |
Paints and varnishes - Determination of pigment content - Part 2: Ashing method |
|
CEN EN ISO 14939 |
Animal Feeding Stuffs - Determination of Carbadox Content - Method using High-Performance Liquid Chromatography-ISO 14939:2001 |
|
CEN EN ISO 15874-1 |
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General-Incorporates Amendment A1: June 2007 |
|
CEN EN ISO 15875-1 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General-Incorporates Amendment A1: June 2007 |
|
CEN EN ISO 15875-3 |
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings-ISO 15875-3:2003 |
|
CEN EN ISO 15876-2 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes-Incorporates Amendment A1: June 2007 |
|
CEN EN ISO 15877-3 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings-ISO 15877-3:2003 |
|
CEN EN ISO 15914 |
Animal feeding stuffs Enzymatic determination of total starch content-ISO 15914:2004 |
|
CEN EN ISO 15927-5 |
Hygrothermal performance of buildings - Calculation and presentation of climatic data - Part 5: Data for design heat load for space heating-ISO 15927-5: 2005 |
|
CEN EN ISO 16472 |
Animal feeding stuffs - Determination of amylase-treated neutral detergent fibre content (aNDF)-ISO 16472:2006 |
|
CEN EN ISO 16484-3 |
Building automation and control systems (BACS) - Part 3: Functions-ISO 16484-3:2005 |
|
CEN EN ISO 17872 |
Paints and varnishes - Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing |
|
CEN EN ISO 17895 |
Paints and varnishes - Determination of the volatile organic compound content of low-VOC emulsion paints (in-can VOC)-ISO 17895:2005 |
|
CEN EN ISO 22254 |
Dentistry - Manual toothbrushes - Resistance of tufted portion to deflection-:1990 |
|
CEN EN ISO 22475-1 |
Geotechnical investigation and testing - Sampling methods and groundwater measurements - Part 1: Technical principles for execution |
|
CEN EN ISO 23953-1 |
Refrigerated display cabinets - Part 1: Vocabulary-ISO 23953-1: 2005; Supersedes EN 441-1: 1994 |
|
CEN EN ISO 2811-2 |
Paints and Varnishes - Determination of Density - Part 2: Immersed Body (Plummet) Method-ISO 2811-2: 1997 |
|
CEN EN ISO 2811-3 |
Paints and Varnishes - Determination of Density - Part 3: Oscillation Method-ISO 2811-3:1997 |
|
CEN EN ISO 2812-5 |
Paints and varnishes - Determination of resistance to liquids - Part 5: Temperature-gradient oven method |
|
CEN EN ISO 3262-10 |
Extenders for Paints - Specifications and Methods of Test - Part 10: Natural Talc/Chlorite in Lamellar Form-ISO 3262-10:2000 |
|
CEN EN ISO 3262-15 |
Extenders for Paints - Specifications and Methods of Test - Part 15: Vitreous Silica-ISO 3262-15:2000 |
|
CEN EN ISO 3262-20 |
Extenders for Paints - Specifications and Methods of Test - Part 20: Fumed Silica-ISO 3262-20:2000 |
|
CEN EN ISO 3262-22 |
Extenders for Paints - Specifications and Methods of Test - Part 22: Flux-Calcined Kieselguhr-ISO 3262-22: 2001 |
|
CEN EN ISO 3262-3 |
Extenders for Paints - Specifications and Methods of Test - Part 3: Blanc Fixe-Together with the Other Parts of BSISO 3262-3:1998 |
|
CEN EN ISO 3262-5 |
Extenders for Paints - Specifications and Methods of Test - Part 5: Natural Crystalline Calcium Carbonate-ISO 3262-5:1998 |
|
CEN EN ISO 4623-2 |
Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates-ISO 4623-2:2003 |
|
CEN EN ISO 4628-10 |
Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 10: Assessment of degree of filiform corrosion-ISO 4628-10:2003 |
|
CEN EN ISO 5912 |
Camping tents-ISO 5912: 2003 |
|
CEN EN ISO 6497 |
Animal feeding stuffs - Sampling-(ISO 6497): 2002 |
|
CEN EN ISO 6504-1 |
Paints and varnishes - Determination of hiding power - Part 1: Kubelka-Munk method for white and light-coloured paints |
|
CEN EN ISO 6744-2 |
Binders for paints and varnishes - Alkyd resins - Part 2: Determination of phthalic anhydride content-ISO 6744-2:1999 |
|
CEN EN ISO 6869 |
Animal Feeding Stuffs - Determination of the Contents of Calcium, Copper, Iron, Magnesium, Manganese, Potassium, Sodium and Zinc - Method Using Atomic Absorption Spectrometry-ISO 6869: 2000 |
|
CEN EN ISO 7784-1 |
Paints and varnishes - Determination of resistance to abrasion - Part 1: Rotating abrasive-paper-covered wheel method |
|
CEN EN ISO 8442-2 |
Materials and articles in contact with foodstuffs Cutlery and table holloware Part 2: Requirements for stainless steel and silver-plated cutlery-Incorporates Corrigendum June 1998 and June 2006; ISO 8442-2:1997 |
|
CEN EN ISO 8780-2 |
Pigments and Extenders - Methods of Dispersion for Assessment of Dispersion Characteristics - Part 2: Dispersion Using an Oscillatory Shaking Machine (ISO 8780-2: 1990) |
|
CEN EN ISO 8795 |
Plastics piping systems for the transport of water intended for human consumption Migration assessment Determination of migration values of plastics pipes and fittings and their joints-ISO 8795: 2001 |
|
CEN EN ISO 9239-1 |
Reaction to Fire Tests for Floorings - Part 1: Determination of the Burning Behaviour Using a Radiant Heat Source-ISO 9239-1: 2002 |
|
CEN EN ISO 9346 |
Thermal Insulation - Mass Transfer - Physical Quantities and Definitions (ISO 9346 : 1987) |
|
CEN EN38 (PART 2) |
Wall Hung WC Pan Part 2 Wall Hung WC Pan with Independent Water Supply Connecting Dimensions |
|
CEN ENV 1170-8 |
Test Method for Glass-Fibre Reinforced Cement - Part 8: Cyclic Weathering Type Test |
|
CEN ENV 12875-1 |
Mechanical Dishwashing Resistance of Domestic Utensils - Part 1: Reference Test Method-Superseded by EN 12875-1 |
|
CEN ENV 1317-4 |
Road Restraint Systems - Part 4: Performance Classes, Impact Test Acceptance Criteria and Test Methods for Terminals and Transitions of Safety Barries |
|
CEN ENV 13459-3 |
Road Marking Materials - Quality Control - Part 3: Performance in Use |
|
CEN ENV 1455-2 |
Plastics Piping Systems for Soil and Waste Discharge (Low and High Temperature) within the Building Structure - Acrylonitrile-Butadiene-Styrene (ABS) - Part 2: Guidance for the Assessment of Conformity |
|
CEN ENV 1566-2 |
Plastics Piping Systems for Soil and Waste Discharge (Low and High Temperature) within the Building Structure - Chlorinated Poly (Vinyl Chloride) (PVC-C) - Part 2: Guidance for the Assessment of Conformity |
|
CEN ENV 1628 |
Windows, Doors, Shutters - Burglar Resistance - Test Method for the Determination of Resistance under Static Loading |
|
CEN ENV 581-2 |
Outdoor Furniture - Seating and Tables for Camping, Domestic and Contract Use - Part 2: Mechanical Safety Requirements and Test Methods for Sampling |
|
CEN ENV 927-2 |
Paints and Varnishes - Coating Materials and Coating Systems for Exterior Wood - Part 2: Performance Specification |
|
CENELEC HD 1000 |
Service and Working Scaffolds Made of Prefabricated Elements Materials, Dimensions, Design Loads and Safety Requirements |
|
CENELEC HD 250.2 |
General Specification for Electric Motor Operated Appliances for Household and Similar Purposes |
|
CENELEC HD 252 |
Particular Specification for Vacuum Cleaners and Water Suction Cleaning Appliances |
|
CENELEC HD 253 S3 |
Safety of Household and Similar Electrical Appliances Part 2: Particular Requirements for Electric Irons |
|
CENELEC HD 257 S2 |
Safety of Household and Similar Electrical Appliances Particular Requirements for Dishwashers |
|
CENELEC HD 260 S3 |
Safety of Household and Similar Electrical Appliances Part 2: Particular Requirements for Coffee Mills and Coffee Grinders |
|
CENELEC HD 261 |
Particular Specification for Kitchen Machines |
|
CENELEC HD 262 |
Particular Specification for Portable Immersion Heaters |
|
CENELEC HD 262 S1 |
Particular Specification for Portable Immersion Heaters |
|
CENELEC HD 262.4 S1 |
Particular Specification for Portable Immersion Heaters |
|
CENELEC HD 266.4 |
Particular Specification for Appliances for Skin or Hair Treatment |
|
CENELEC HD 267 S1 |
Safety of Household and Similar Electrical Appliances - Particular Requirements for Spin Extractors |
|
CENELEC HD 270 S1 |
Safety of Household and Similar Electrical Appliances - Particular Requirements for Microwave Cooking Appliances |
|
CENELEC HD 270 S1 |
Safety of Household Similar Electrical Appliances Particular Requirements for Microwave Cooking Appliances |
|
CENELEC HD 271 S1/ A1 |
AMD 1 Safety of Household and Similar Electrical Appliances Particular Requirements for Electric Toys Supplied at Safety Extra-Low Voltage-Superseded by EN 50088:1996 |
|
CENELEC HD 271 S1/ A3 |
AMD 3 Safety of Household and Similar Electrical Appliances Particular Requirements for Electric Toys Supplied at Safety Extra-Low Voltages-Superseded by EN 50088:1996 |
|
CENELEC HD 274 S2 |
Safety of Household and Similar Electrical Appliances Requirements for the Connection of Washing Machines, Dishwashers and Tumble Dryers to the Water Supply Mains |
|
CENELEC HD 275 S1 |
Safety of Household and Similar Electrical Appliances - Part 2: Particular Requirements for Cooking Ranges, Cooking Tables, Ovens and Similar Appliances for Household Use |
|
CENELEC HD 277 S1 |
Safety of Household and Similar Electrical Appliances - Particular Requirements for Motor- Compressors |
|
CENELEC HD 278 S1/ A5 |
AMD 5 Safety of Household and Similar Electrical Appliances - Part 2: Particular Requirements for Room Heaters; |
|
CENELEC HD 359 |
Flat Polyvinylchloride Sheathed Cables for Lifts and Similar Applications |
|
CENELEC HD 359.2 |
Flat Polyvinyl Chloride Sheathed Flexible Cables for Lifts and Similar Applications |
|
CENELEC HD 384.4.45 S1 |
Electrical Installations of Buildings-Part 4: Protection for Safety. Chapter 45: Protection Against Undervoltage |
|
CENELEC HD 384.4.46 S1 |
Electrical Installations of Buildings - Part 4: Protection for Safety. Chapter 46: Isolation and Switching |
|
CENELEC HD 384.5.52 S1/A1 |
AMD 1 Electrical Installations of Buildings Part 5: Selection and Erection of Electrical Equipment Chapter 52: Wiring Systems-Corrigendum September 1998 |
|
CEN CEN ISO/TS 22475-2 |
Geotechnical investigation and testing - Sampling methods and groundwater measurements - Part 2: Qualification criteria for enterprises and personnel |
|
CEN CEN/TR 14920 |
Jetting resistance of drain and sewer pipes - Moving jet test method |
|
CEN CEN/TR 15128 |
Survey of European Standards for rehabilitation of drain and sewer systems |
|
CEN CEN/TS 13126-17 |
Building hardware, fittings for windows and door height windows Requirements and test methods Part 17: Fittings for tilt and slide systems |
|
CEN CEN/TS 13126-6 |
Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 6: Variable geometry stay hinges (with or without a friction system) |
|
CEN CEN/TS 14383-3 |
Prevention of crime - Urban planning and building design - Part 3: Dwellings |
|
CEN CEN/TS 14754-1 |
Curing compounds - Test methods - Part 1: Determination of water retention efficiency of common curing compounds |
|
CEN CEN/TS 14758-2 |
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 2: Guidance for the assessment of conformity |
|
CEN CEN/TS 15084 |
Liming materials - Guide to the determination of the lime requirement |
|
CEN CEN/TS 15475 |
Fertilizers - Determination of ammoniacal nitrogen |
|
CEN CEN/TS 15477 |
Fertilizers - Determination of the water-soluble potassium content |
|
CEN CEN/TS 15680 |
Prefabricated timber stairs - Mechanical test methods |
|
CEN CEN/TS 772-22 |
Methods of test for masonry units - Part 22: Determination of freeze/thaw resistance of clay masonry units |
|
CENELEC CLC/TR 50506-1 |
Railway applications - Communication, signalling and processing systems - Application Guide for EN 50129 - Part 1: Cross-acceptance |
|
CENELEC CLC/TR 50511 |
Railway applications - Communications, signalling and processing systems - ERTMS/ETCS - External signalling for lines equipped with ERTMS/ETCS Level 2 |
|
CEN CR 13933 |
Masonry Cement - Testing for Workability (Cohesivity) |
|
CEN EN 100 |
Ceramic Tiles - Determination of Modulus of Rupture |
|
CEN EN 1008 |
Mixing Water for Concrete - Specification for Sampling, Testing and Assessing the Suitability of Water, Including Water Recovered from Processes in the Concrete Industry, as Mixing Water for Concrete |
|
CEN EN 1013-4 |
Light Transmitting Profiled Plastic Sheeting for Single Skin Roofing - Part 4: Specific Requirements, Test Methods and Performance of Polycarbonate (PC) Sheets |
|
CEN EN 1015-2 |
Methods of Test for Mortar for Masonry - Part 2: Bulk Sampling of Mortars and Preparation of Test Mortars-Incorporating Amendment 1: 12/2006 |
|
CEN EN 1015-21 |
Methods of Test for Mortar for Masonry - Part 21: Determination of the Compatibility of One-Coat Rendering Mortars with Substrates |
|
CEN EN 1015-4 |
Methods of Test for Mortar for Masonry - Part 4: Determination of Consistence of Fresh Mortar (by Plunger Penetration) |
|
CEN EN 1015-6 |
Methods of Test for Mortar for Masonry - Part 6: Determination of Bulk Density of Fresh Mortar-Incorporating Amendment 1: 2006 |
|
CEN EN 102 |
Ceramic Tiles - Determination of Resistance to Deep Abrasion - Unglazed Tiles |
|
CEN EN 1020 |
Non-Domestic Gas-Fired Forced Convection Air Heaters for Space Heating Not Exceeding a Net Heat Input of 300 kW, Incorporating a Fan to Assist Transportation of Combustion Air and/or Combustion Products-Includes Amendment A1: 2001 |
|
CEN EN 1052-4 |
Methods of Test for Masonry - Part 4: Determination of Shear Strength Including Damp Proof Course |
|
CEN EN 1062-11 |
Paints and Varnishes - Coating Materials and Coating Systems for Exterior Masonry and Concrete - Part 11: Methods of Conditioning Before Testing |
|
CEN EN 107 |
Methods of Testing Windows: Mechanical Tests |
|
CEN EN 1097-5 |
Test for Mechanical and Physical Properties of Aggregates - Part 5: Determination of the Water Content by Drying in a Ventilated Oven |
|
CEN EN 1097-9 |
Tests for mechanical and physical properties of aggregates Part 9: Determination of the resistance to wear by abrasion from studded tyres Nordic test-Includes Amendment A1:2005 |
|
CEN EN 1107-2 |
Flexible Sheets for Waterproofing - Determination of Dimensional Stability - Part 2: Plastic and Rubber Sheets for Roof Waterproofing |
|
CEN EN 1108 |
Flexible Sheets for Waterproofing - Bitumen Sheets for Roof Waterproofing - Determination of Form Stability under Cyclical Temperature Changes |
|
CEN EN 1109 |
Flexible Sheets for Waterproofing - Bitumen Sheets for Roof Waterproofing - Determination of Flexibility at Low Temperature |
|
CEN EN 1111 |
Sanitary Tapware - Thermostatic Mixing Valves (PN-10) - General Technical Specification |
|
CEN EN 1168 |
Precast concrete products - Hollow core slabs |
|
CEN EN 1170-1 |
Precast Concrete Products - Test Method for Glass-Fibre Reinforced Cement - Part 1: Measuring the Consistency of the Matrix `Slump Test´ Method |
|
CEN EN 1191 |
Windows and Doors - Resistance to Repeated Opening and Closing - Test Method |
|
CEN EN 12002 |
Adhesives for Tiles - Determination of Transverse Deformation for Cementitious Adhesives and Grouts |
|
CEN EN 12004 |
Adhesives for tiles - Requirements, evaluation of conformity, classification and designation |
|
CEN EN 12051 |
Building Hardware - Door and Window Bolts - Requirements and Test Methods |
|
CEN EN 12078 |
Zero Governors for Gas Burners and Gas Burning Appliances |
|
CEN EN 12103 |
Resilient Floor Coverings - Agglomerated Cork Underlays - Specification |
|
CEN EN 12159 |
Builders Hoists for Persons and Materials with Vertically Guided Cages |
|
CEN EN 12171 |
Heating Systems in Buildings - Procedure for the Preparation of Documents for Operation, Maintenance and Use - Heating Systems not Requiring a Trained Operator |
|
CEN EN 12194 |
Shutters, External and Internal Blinds - Misuse - Test Methods |
|
CEN EN 122 |
Ceramic Tiles - Determination of Chemical Resistance - Glazed Tiles |
|
CEN EN 12200-1 |
Plastics Rainwater Piping Systems for Above Ground External Use - Unplasticized Poly (Vinyl Chloride) (PVC-U) - Part 1: Specifications for Pipes, Fittings and the System |
|
CEN EN 12237 |
Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts |
|
CEN EN 12244-1 |
Direct Gas-Fired Washing Machines, of Nominal Heat Input Not Exceeding 20 kW - Part 1: Safety |
|
CEN EN 12269-1 |
Determination of the Bond Behaviour between Reinforcing Steel and Autoclaved aerated Concrete by the |
|
CEN EN 12271 |
Surface dressing - Requirements |
|
CEN EN 12272-2 |
Surface dressing - Test methods - Part 2: Visual assessment of defects |
|
CEN EN 12274-5 |
Slurry surfacing - Test method - Part 5: Determination of wearing |
|
CEN EN 12316-1 |
Flexible Sheets for Waterproofing - Determination of Peel Resistance of Joints - Part 1: Bitumen Sheets for Roof Waterproofing |
|
CEN EN 12317-1 |
Flexible Sheets for Waterproofing - Determination of Shear Resistance of Joints - Part 1: Bitumen Sheets for Roof Waterproofing |
|
CEN EN 12325-1 |
Irrigation Techniques - Centre Pivot and Moving Lateral Systems - Part 1: Presentation of the Technical Characteristics |
|
CEN EN 12346 |
Gymnastic Equipment - Wall Bars, Lattice Ladders and Climbing Frames - Safety Requirements and Test Methods |
|
CEN EN 12350-3 |
Testing fresh concrete - Part 3: Vebe test |
|
CEN EN 12370 |
Natural Stone Test Methods - Determination of Resistance to Salt Crystallisation |
|
CEN EN 12390-4 |
Testing Hardened Concrete - Part 4: Compressive Strength - Specification for Testing Machines |
|
CEN EN 12390-7 |
Testing Hardened Concrete - Part 7: Density of Hardened Concrete-Incorporating Corrigendum September 2004 |
|
CEN EN 12412-2 |
Thermal performance of windows, doors and shutters Determination of thermal transmittance by hot box method Part 2: Frames |
|
CEN EN 12424 |
Industrial, Commercial and Garage Doors and Gates - Resistance to Wind Load - Classification |
|
CEN EN 12426 |
Industrial, Commercial and Garage Doors and Gates - Air Permeability - Classification |
|
CEN EN 12428 |
Industrial, Commercial and Garage Doors and Gates - Thermal Transmittance - Requirements for the Calculation |
|
CEN EN 12431 |
Thermal Insulation Products for Building Applications - Determination of Thickness for Floating Floor Insulating Products-Incorporating A1: September 2006 |
|
CEN EN 12464-2 |
Lighting of work places - Part 2: Outdoor work places |
|
CEN EN 12489 |
Industrial, Commercial and Garage Doors and Gates - Resistance to Water Penetration - Test Method |
|
CEN EN 12491 |
Paragliding Equipment - Emergency Parachutes - Safety Requirements and Test Methods |
|
CEN EN 12502-5 |
Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels |
|
CEN EN 12503-4 |
Sports Mats - Part 4: Determination of Shock Absorption |
|
CEN EN 12503-5 |
Sports Mats - Part 5: Determination of the Base Friction |
|
CEN EN 12503-6 |
Sports Mats - Part 6: Determination of the Top Friction |
|
CEN EN 12572 |
Artificial Climbing Structures - Protection Points, Stability Requirements and Test Methods |
|
CEN EN 12572-1 |
Artificial climbing structures - Part 1: Safety requirements and test methods for ACS with protection points |
|
CEN EN 12615 |
Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Determination of Slant Shear Strength |
|
CEN EN 12619 |
Stationary Source Emissions - Determination of the Mass Concentration of Total Gaseous Organic Carbon at Low Concentrations in Flue Gases - Continuous Flame Ionization Detector Method |
|
CEN EN 12629-1 |
Machines for the Manufacture of Constructional Products from Concrete and Calcium-Silicate - Safety - Part 1: Common Requirements |
|
CEN EN 12629-4 |
Machines for the Manufacture of Constructional Products from Concrete and Calcium-Silicate - Safety - Part 4: Concrete Roof Tile Making Machines |
|
CEN EN 1266 |
Independent gas-fired convection heaters incorporating a fan to assist transportation of combustion air and/or flue gases-Includes amendment A1:2005 |
|
CEN EN 12664 |
Thermal Performance of Building Materials and Products - Determination of Thermal Resistance by Means of Guarded Hot Plate and Heat Flow Meter Methods - Dry and Moist Products of Medium and Low Thermal Resistance |
|
CEN EN 12669 |
Direct Gas-Fired Hot Air Blowers for Use in Greenhouses and Supplementary Non-Domestic Space Heating |
|
CEN EN 12691 |
Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to impact |
|
CEN EN 12697-14/AC |
Bituminous Mixtures - Test Methods for Hot Mix Asphalt - Part 14: Water Content-Corrigendum; Ratified European Text |
|
CEN EN 12697-23 |
Bituminous mixtures - Test methods for hot mix asphalt - Part 23: Determination of the indirect tensile strength of bituminous specimens |
|
CEN EN 12697-26 |
Bituminous mixtures - Test methods for hot mix asphalt - Part 26: Stiffness |
|
CEN EN 12697-37 |
Bituminous mixtures Test methods for hot mix asphalt Part 37: Hot sand test for the adhesivity of binder on precoated chippings for HRA-(R) |