|
CEN EN 1861 |
Refrigerating Systems and Heat Pumps - System Flow Diagrams and Piping and Instrument Diagrams - Layout and Symbols |
|
CEN EN 1964-2 |
Transportable Gas Cylinders - Specification for the Design and Construction of Refillable Transportable Seamless Steel Gas Cylinders of Water Capacities from 0,5 Litre Up to and Including 150 Litres - Part 2: Cylinders Made of Seamless Steel with and Rm Value of 1 100 MPa and Above |
|
CEN EN 20865 |
Slots in Platens for Projection Welding Machines |
|
CEN EN 21089 |
Electrode Taper Fits for Spot Welding Equipment - Dimensions |
|
CEN EN 22063 |
Metallic and Other Inorganic Coatings - Thermal Spraying - Zinc, Aluminium and Their Alloys (ISO 2063 : 1991 Modified) |
|
CEN EN 22857 |
Ground Thread Taps for ISO Metric Threads of Tolerances 4H to 8H and 4G to 6G Coarse and Fine Pitches; Manufacturing Tolerances on the Threaded Portion |
|
CEN EN 253 |
District heating pipes Preinsulated bonded pipe systems for directly buried hot water networks Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene-Includes amendment A1:2005 |
|
CEN EN 264 |
Safety Shut-Off Devices for Combustion Plants Using Liquid Fuels; Safety Requirements and Testing |
|
CEN EN 26704 |
Automatic Steam Traps - Classification |
|
CEN EN 26801 |
Rubber and Plastics Hoses - Determination of Volumetric Expansion (ISO 6801: 1983) |
|
CEN EN 27721 |
Countersunk Head Screws - Head Configuration and Gauging |
|
CEN EN 28653 |
Adhesives - Test Method for Shear Impact Strength of Adhesive Bonds (ISO 9653 : 1991) |
|
CEN EN 28662-3 |
Hand-Held Portable Power Tools - Measurement of Vibrations at the Handle - Part 3: Rock Drills and Rotary Hammers (ISO 8662-3:1992)-Includes Amendments A1:1995 and A2:2001; ISO 8662-3:1992 |
|
CEN EN 293 |
Oil Pressure Atomizing Nozzles - Minimum Requirements - Testing |
|
CEN EN 29455-1 |
Soft Soldering Fluxes - Test Methods - Part 1 : Determination of Non-Volatile Matter, Gravimetric Method (ISO 9455-1 : 1990) |
|
CEN EN 29455-14 |
Soft Soldering Fluxes - Test Methods - Part 14: Assessment of Tackiness of Flux Residues (ISO 9455-14 : 1991) |
|
CEN EN 29455-5 |
Soft Soldering Fluxes - Test Methods - Part 5: Copper Mirror Test (ISO 9455-5 : 1992) |
|
CEN EN 295-3 |
Vitrified Clay Pipes and Fittings and Pipe Joints for Drains and Sewers Part 3: Test Methods-Includes Amendment A1: 1998 |
|
CEN EN 331 |
Manually Operated Ball Valves and Closed Bottom Taper Plug Valves for Gas Installations for Buildings |
|
CEN EN 448 |
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
|
CEN EN 45510-5-1 |
Guide for Procurement of Power Station Equipment - Part 5-1: Steam Turbines |
|
CEN EN 45510-5-3 |
Guide for Procurement of Power Station Equipment - Part 5-3: Wind Turbines |
|
CEN EN 45510-5-4 |
Guide for Procurement of Power Station Equipment - Part 5-4: Hydraulic Turbines, Storage Pumps and Pump-Turbines |
|
CEN EN 45510-8-1 |
Guide for Procurement of Power Station Equipment - Part 8-1: Control and Instrumentation |
|
CEN EN 488 |
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
|
CENELEC EN 50006 |
The Limitation of Disturbances in Electricity Supply Networks Caused by Domestic and Similar Appliances Equipped with Electronic Devices |
|
CENELEC EN 50024 |
Low Voltage Switchgear and Controlgear for Industrial Use: Mounting Rails; C- Profile and Accessories for the Mounting of Equipment |
|
CENELEC EN 50085-2-3 |
Cable Trunking Systems and Cable Ducting Systems for Electrical Installations - Part 2-3: Particular Requirements for Slotted Cable Trucking Systems Intended for Installation in Cabinets |
|
CENELEC EN 50089 |
Cast Resin Partitions for Metal Enclosed Gas-Filled High Voltage Switchgear and Controlgear |
|
CENELEC EN 50122-2 |
Railway Applications - Fixed Installations - Part 2: Protective Provisions Against the Effects of Stray Currents Caused by d.c. Traction Systems-Includes Amendment A1: 2002; Incorporating Corrigendum August 2001 |
|
CENELEC EN 50216-5 |
Power transformer and reactor fittings Part 5: Liquid level, pressure and flow indicators, pressure relief devices and dehydrating breathers-Incorporates Amendments A1:2002, A2:2005 and A3: 2006 |
|
CENELEC EN 50216-7 |
Power Transformer and Reactor Fittings Part 7: Electric Pumps for Transformer Oil |
|
CENELEC EN 50243 |
Outdoor Bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for Liquid Filled Transformers |
|
CENELEC EN 50250 |
Conversion adaptors for industrial use-Incorporates Corrigendum August 2007 |
|
CENELEC EN 50260-2-5 |
Safety of Hand-Held Battery-Powered Motor-Operated Tools and Battery Packs Part 2-5: Particular Requirements for Circular Saws and Circular Knives-Superseded by EN 60745-2-5: June 2003 |
|
CENELEC EN 50266-1 |
Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables - Part 1: Apparatus-Supersedes HD 405.3 S1:1993 |
|
CENELEC EN 50266-2-2 |
Common Test Methods for Cables under Fire Conditions - Test for Vertical Flame Spread of Vertically-Mounted Bunched Wires or Cables Part 2-2: Procedures - Category A-Supersedes HD 405.3 S1: 1993; Incorporating Corrigendum March 2002 |
|
CENELEC EN 50274 |
Low-Voltage Switchgear and Controlgear Assemblies - Protection Against Electric Shock - Protection Against Unintentional Direct Contact with Hazardous Live Parts |
|
CENELEC EN 50290-2-23 |
Communication Cables - Part 2-23: Common Design Rules and Construction - PE Insulation-:1994 |
|
CENELEC EN 50290-2-27 |
Communication cables - Part 2-27: Common design rules and construction - Halogen free flame retardant thermoplastic sheathing compounds-Incorporating Amendment A1: June 2007 |
|
CENELEC EN 50305 |
Railway Applications - Railway Rolling Stock Cables Having Special Fire Performance - Test Methods |
|
CENELEC EN 50326 |
Conductors for overhead lines - Characteristics of greases |
|
CENELEC EN 50355 |
Railway applications - Railway rolling stock cables having special fire performance - Thin wall and standard wall - Guide to use |
|
CENELEC EN 50362 |
Method of test for resistance to fire of larger unprotected power and control cables for use in emergency circuits |
|
CENELEC EN 50363-1 |
Insulating, sheathing and covering materials for low voltage energy cables Part 1: Cross-linked elastomeric insulating compounds |
|
CEN EN 50363-7 |
Insulating, sheathing and covering materials for low voltage energy cables Part 7: Halogen-free, thermoplastic insulating compounds |
|
CENELEC EN 50380 |
Datasheet and nameplate information for photovoltaic modules |
|
CENELEC EN 50464-2-1 |
Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV - Part 2-1: Distribution transformers with cable boxes on the high-voltage and/or low-voltage side - General requirements |
|
CENELEC EN 50497 |
Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables |
|
CEN EN 580 |
Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT) |
|
CENELEC EN 60041 |
Field Acceptance Tests to Determine the Hydraulic Performance of Hydraulic Turbines, Storage Pumps and Pump-Turbines (IEC 41 : 1991, Modified) |
|
CENELEC EN 60044-6 |
Instrument Transformers Part 6: Requirements for Protective Current Transformers for Transient Performance-IEC 60044-6: 1992, Modified |
|
CENELEC EN 60192 |
Low Pressure Sodium Vapour Lamps - Performance Specifications-IEC 60192:2001 |
|
CENELEC EN 60247 |
Insulating liquids Measurement of relative permittivity, dielectric dissipation factor (tan $) and d.c. resistivity-IEC 60247:2004 |
|
CENELEC EN 60255-26 |
Electrical relays Part 26 : Electromagnetic compatibility requirements for measuring relays and protection equipment-IEC 60255-26:2004 |
|
CENELEC EN 60265-1 |
High-Voltage Switches Part 1: Switches for Rated Voltages Above 1 kV and Less Than 52 kV-IEC 60265-1:1998; Supersedes HD 355.1 S3:1995 |
|
CENELEC EN 60269-1 |
Low-Voltage Fuses - Part 1: General Requirements |
|
CENELEC EN 60308 |
Hydraulic turbines Testing of control systems-IEC 60308:2005 |
|
CENELEC EN 60317-0-5 |
Specifications for particular types of winding wires Part 0-5: General requirements - Glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire |
|
CENELEC EN 60317-2 |
Specifications for Particular Types of Winding Wires - Part 2: Solderable Polyurethane Enamelled Round Copper Wire, Class 130, with a Bonding Layer-Includes Amendments A1: 1998 and A2: 2000; IEC 60317-2:1990 & A1:1997 & A2: 1999; Supersedes HD 555.2 S2: 1992 |
|
CENELEC EN 60317-28 |
Specifications for particular types of winding wires Part 28: Polyesterimide enamelled rectangular copper wire, class 180 (IEC 60317-28:-Incorporating Amendments A1: 1/1998, and A2: 7/2007 |
|
CENELEC EN 60317-49 |
Specifications for Particular Types of Windind Wires - Part 49: Glass-Fibre Wound Resin or Varnish Impregnated, Bare or Enamelled Round Copper Wire, Temperature Index 180-IEC 60317-49:1999 |
|
CENELEC EN 60371-3-7 |
Insulating materials based on mica Part 3: Specifications for individual materials Sheet 7: Polyester film mica paper with an epoxy resin binder for single conductor taping-Incorporates Amendment 1: 11/2006 |
|
CENELEC EN 60376 |
Specification of technical grade sulfur hexafluoride (SF6) for use in electrical equipment-IEC 60376: 2005 |
|
CENELEC EN 60454-3-3 |
Pressure-Sensitive Adhesive Tapes for Electrical Purposes - Part 3: Specifications for Individual Materials - Sheet 3: Polyester Film Tapes with Rubber Thermoplastic Adhesive-IEC 60454-3-3:1998 |
|
CENELEC EN 60455-3-5 |
Resin Based Reactive Compounds Used for Electrical Insulation Part 3: Specifications for Individual Materials Sheet 5: Unsaturated Polyester Based Impregnating Resins |
|
CENELEC EN 60464-3-1 |
Varnishes Used for Electrical Insulation Part 3: Specifications for Individual Materials Sheet 1: Ambient Curing Finishing Varnishes-Includes amendment A1:2006; IEC 60464-3-1:2001 + A1:2006 |
|
CENELEC EN 60465 |
Specification for Unused Insulating Mineral Oils For Cables with Oil Ducts |
|
CENELEC EN 60519-2 |
Safety in electroheat installations Part 2: Particular requirements for resistance heating equipment-IEC 60519-2:2006 |
|
CENELEC EN 60519-8 |
Safety in electroheat installations Part 8: Particular requirements for electroslag remelting furnaces-IEC 60519-8:2005 |
|
CENELEC EN 60534-2-5 |
Industrial-process control valves Part 2-5: Flow capacity Sizing equations for fluid flow through multistage control valves with interstage recovery-IEC 60534-2-5:2003 |
|
CENELEC EN 60534-3-1 |
Industrial-Process Control Valves Part 3-1: Dimensions - Face-To-Face Dimensions for Flanged, Two-Way, Globe-Type, Straight Pattern and Centre-To-Face Dimensions for Flanged, Two-Way, Globe-Type, Angle Pattern Control Valves-Incorporates Corrigendum July 2000; IEC 60534-3-1: 2000 |
|
CENELEC EN 60534-6-2 |
Industrial-Process Control Valves Part 6-2: Mounting Details for Attachment of Positioners to Control Valves - Positioner Mounting on Rotary Actuators-IEC 60534-6-2:2000 |
|
CENELEC EN 60534-8-2 |
Industrial-Process Control Valves Part 8: Noise Considerations Section 2: Laboratory Measurement of Noise Generated by Hydrodynamic Flow Through Control Valves (IEC 534-8-2 : 1991) |
|
CENELEC EN 60534-8-4 |
Industrial-process control valves Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow |
|
CENELEC EN 60534-9 |
Industrial-process control valves - Part 9: Test procedure for response measurements from step inputs |
|
CENELEC EN 60544-5 |
Electrical insulating materials Determination of the effects of ionizing radiation Part 5: Procedures for assessment of ageing in service-IEC 60544-5:2003 |
|
CENELEC EN 60623 |
Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes - Vented Nickel-Cadmium Prismatic Rechargeable Single Cells-IEC 60623: 2001 |
|
CENELEC EN 60644 |
Specification for High- Voltage Fuse-Links for Motor Circuit Applications; (IEC 644:1979) |
|
CENELEC EN 60654-3 |
Operating Conditions for Industrial-Process Measurement and Control Equipment Part 3: Mechanical Influences-IEC 60654-3: 1983; Supersedes HD 413.3 S1: 1987 |
|
CENELEC EN 60669-2-4 |
Switches for household and similar fixed electrical installations Part 2-4: Particular requirements - Isolating switches-IEC 60669-2-4:2004, modified |
|
CENELEC EN 60670-22 |
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations Part 22: Particular requirements for connecting boxes and enclosures |
|
CENELEC EN 60674-3-4 TO 6 |
Specification for Plastic Films for Electrical Purposes Part 3: Specifications for Individual Materials Sheets 4 to 6: Requirements for Polyimide Films Used for Electrical Insulation (IEC 674-3-4 to 6 : 1993) |
|
CENELEC EN 60676 |
Industrial electroheating equipment - Test methods for direct arc furnaces-IEC 60676: 2002; Supersedes HD 598 S1: 1992 |
|
CENELEC EN 60684-2 |
Flexible insulating sleeving Part 2: Methods of test-Includes amendments A1:2003 and A2:2005; IEC 60684-2:1997/A1:2003; Supersedes HD 523.2 S2:1993 |
|
CENELEC EN 60684-3-248 |
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 248: General purpose, heat-shrinkable, dual wall polyolefin sleeving, flame retarded, shrink ratios 2:1, 3:1, 4:1 |
|
CENELEC EN 60684-3-320 |
Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 320: Polyethylene terephthalate textile sleeving, lightly impregnated-IEC 60684-3-320: 2002; Supersedes HD 523.3.320 S1: 1989 |
|
CENELEC EN 60684-3-409 |
Flexible Insulating Sleeving Part 3: Specifications for Individual Types of Sleeving Sheet 409: Glass Textile Sleeving with Polyurethane (PUR)-Based Coating-IEC 60684-3-409:1999 |
|
CENELEC EN 60745-2-13 |
Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for chain saws |
|
CENELEC EN 60745-2-21 |
Hand-held motor-operated electric tools - Safety - Part 2-21: Particular requirements for drain cleaners |
|
CENELEC EN 60770-2 |
Transmitters for use in industrial-processcontrol systems Part 2: Methods for inspection and routine testing-IEC 60770-2:2003 |
|
CENELEC EN 60811-1-3 |
Insulating and Sheathing Materials of Electric Cables - Common Test Methods - Part 1-3: General Application - Methods for Determining the Density - Water Absorption Tests - Shrinkage Test-Includes Amendment A1: 2001; IEC 60811-1-3: 1993 + A1: 2001; Supersedes HD 505.1-2 S2: 1991 |
|
CENELEC EN 60811-4-1 |
Insulating and sheathing materials of electric and optical cables Common test methods Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by termogravimetric-IEC 60811-4-1:2004 |
|
CENELEC EN 60811-5-1 |
Insulating and sheathing materials of electric and optical fibre cables Common test methods Part 5-1: Methods specific to filling compounds Drop point Separation of oil Lower temperature brittleness Total acid number Absence of corrosive components Permittivity at 23°C D.C resistivity at 23°C and 100°C-Includes Amendment A1:2004; IEC 60811-5-1:1990 modified + A1:2004 |
|
CENELEC EN 60819-3-3 |
Non-cellulosic papers for electrical purposes Part 3: Specifications for individual materials - Sheet 3: Unfilled aramid (aromatic polyamide) papers-IEC 60819-3-3:2006 |
|
CENELEC EN 60838-2-2 |
Miscellaneous lampholders Part 2-2: Particular requirements - Connectors for LED-modules-IEC 60838-2-2:2006 |
|
CENELEC EN 60893-2 |
Insulating materials Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Part 2: Methods of test-IEC 60893-2:2003 |
|
CENELEC EN 60893-3-1 |
Specification for Industrial Rigid Laminated Sheets Based on Thermosetting Resins for Electrical Purposes Part 3: Specifications for Individual Materials Sheet 1: Types of Industrial Rigid Laminated Sheets |
|
CENELEC EN 60893-3-2 |
Insulating materials Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Part 3-2: Specifications for individual materials Requirements for rigid laminated sheets based on epoxy resins-IEC 60893-3-2:2003 |
|
CENELEC EN 60893-3-4 |
Insulating materials Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Part 3-4: Specifications for individual materials Requirements for rigid laminated sheets based on phenolic resins-IEC 60893-3-4:2003 |
|
CENELEC EN 60893-3-5 |
Insulating materials Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Part 3-5: Specifications for individual materials Requirements for rigid laminated sheets based on polyester resins-IEC 60893-3-5:2003 |
|
CENELEC EN 60896-22 |
Stationary lead-acid batteries Part 22: Valve regulated types Requirements-IEC 60896-22:2004 |
|
CENELEC EN 60928 |
Auxiliaries for Lamps - A.C. Supplied Electronic Ballasts for Tubular Fluorescent Lamps - General and Safety Requirements-Includes Amendment A1:1999; IEC 60928:1995 + A1:1999; Superseded by EN 61347-2-3: 2001 |
|
CENELEC EN 60938-2 |
Fixed Inductors for Electromagnetic Interference Suppression Part 2: Sectional Specification-Incorporates Amendment 1: February 2007 |
|
CENELEC EN 60953-2 |
Rules for Steam Turbine Thermal Acceptance Tests Part 2: Method B Wide Range of Accuracy for Various Types and Sizes of Turbines-IEC 953-2: 1990 |
|
CENELEC EN 60974-11 |
Arc welding equipment Part 11: Electrode holders-IEC 60974-11:2004 |
|
CENELEC EN 60974-8 |
Arc welding equipment Part 8: Gas consoles for welding and plasma cutting systems-IEC 60974-8:2004 |
|
CENELEC EN 61029-2-11 |
Safety of transportable motor-operated electric tools Part 2-11: Particular requirements for combined mitre and bench saws-IEC 61029-2-11:2001, modified |
|
CENELEC EN 61033 |
Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate |
|
CENELEC EN 61068-2 |
Specification for Polyester Fibre Woven Tapes Part 2: Methods of Test-IEC 61068-2: 1991 |
|
CENELEC EN 61158-2 |
Digital data communications for measurement and control - Fieldbus for use in industrial control systems Part 2: Physical layer specification and service definition-IEC 61158-2:2003 + corrigendum 2004; Partially supersedes EN 50170:1996 + A1:2002 + A2:1999 + A3:2002 and EN 50254:1998 |
|
CENELEC EN 61163-1 |
Reliability stress screening Part 1: Repairable assemblies manufactured in lots |
|
CENELEC EN 61166 |
High-Voltage Alternating Current Circuit-Breakers Guide for Seismic Qualification of High- Voltage Alternating Current Circuit- Breakers (IEC 1166 : 1993) |
|
CENELEC EN 61211 |
Insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1 000 V Impulse puncture testing in air-IEC 61211:2004 |
|
CENELEC EN 61212-3-2 |
Industrial Rigid Round Laminated Tubes and Rods Based on Thermosetting Resins for Electrical Purposes Part 3: Specifications for Individual Materials Sheet 2: Round Laminated Moulded Tubes-IEC 61212-3-2:2006 |
|
CENELEC EN 61248-2 |
Transformers and Inductors for Use in Electronic and Telecommunication Equipment Part 2: Sectional Specification for Signal Transformers on the Basis of the Capability Approval Procedure-IEC 61248-2: 1996 |
|
CENELEC EN 61264 |
Ceramic Pressurized Hollow Insulators for High-Voltage Switchgear and Controlgear-IEC 61264:1998; Incorporating Corrigendum July 2000; Supersedes EN 50062:1991; Superseded by EN 62155:2003 |
|
CENELEC EN 61298-3 |
Process Measurement and Control Devices General Methods and Procedures for Evaluating Performance Part 3: Tests for the Effects of Influence Quantities-IEC 61298-3:1998 |
|
CENELEC EN 61386-1 |
Conduit systems for cable management Part 1: General requirements-Incorporates Corrigendum April 2004; IEC 61386-1:1996 + A1:2000 |
|
CENELEC EN 61400-12-1 |
Part 12-1: Power performance measurements of electricity producing wind turbines-IEC 61400-12-1: 2005; Supersedes EN 61400-12: 1998 |
|
CENELEC EN 61400-25-1 |
Fertilizers - Determination of cyanamide nitrogen |
|
CENELEC EN 61479 |
Live working Flexible conductor covers (line hoses) of insulating material-Includes amendment A1: 2002; IEC 61479: 2001 + A1: 2002 |
|
CENELEC EN 61534-1 |
Powertrack systems Part 1: General requirements-IEC 61534-1:2003 |
|
CENELEC EN 61534-21 |
Powertrack systems Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting-IEC 61534-21:2006 |
|
CENELEC EN 61537 |
Cable management - Cable tray systems and cable ladder systems |
|
CENELEC EN 61605 |
Fixed inductors for use in electronic and telecommunication equipment - Marking codes-IEC 61605: 2005 |
|
CENELEC EN 61660-2 |
Short-Circuit Currents in D.C. Auxiliary Installations in Power Plants and Substations Part 2: Calculation of Effects-IEC 61660-2: 1997 |
|
CENELEC EN 61730-2 |
Photovoltaic (PV) module safety qualification - Part 2: Requirements for testing |
|
CENELEC EN 61773 |
Overhead Lines Testing of Foundations for Structures-IEC 1773: 1996 |
|
CENELEC EN 61788-3 |
Superconductivity Part 3: Critical current measurement - DC critical current of Ag-sheathed Bi-2212 and Bi-2223 oxide superconductors-IEC 61788-3: 2006 |
|
CEN EN 61788-9 |
Superconductivity Part 9: Measurements for bulk high temperature superconductors - Trapped flux density of large grain oxide superconductors |
|
CENELEC EN 61800-5-2 |
Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
|
CENELEC EN 61811-1 |
Electromechanical Non-Specified Time All-Or-Nothing Relays of Assessed Quality - Part 1: Generic Specification-IEC 61811-1: 1999; Supersedes EN 116000-1: 1996 |
|
CENELEC EN 61811-10 |
Electromechanical elementary relays of assessed quality Part 10: Sectional specification Relays for industrial application-IEC 61811-10:2002 |
|
CENELEC EN 61811-52 |
Electromechanical All-or-Nothing Relays Part 52: Blank Detail Specification Electromechanical All-or-Nothing Telecom Relays of Assessed Quality Two Change-Over Contacts, 20 mm x 10 mm Base-IEC 61811-52: 2002; Supersedes EN 116502: 1992 |
|
CENELEC EN 61858 |
Electrical insulation systems Thermal evaluation of modifications to an established wire-wound EIS-IEC 61858:2004 |
|
CENELEC EN 62155 |
Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1000 V-Supersedes HD 329 S1:1977 and EN 61264:1998; IEC 62155:2003, modified |
|
CENELEC EN 62199 |
Bushings for d.c. application-IEC 62199:2004 |
|
CENELEC EN 62217 |
Polymeric insulators for indoor and outdoor use with a nominal voltage > 1 000 V - General definitions, test methods and acceptance criteria-Incorporating Corrigendum: 12/2006 |
|
CENELEC EN 62271-100 |
High-voltage switchgear and controlgear Part 100: High-voltage alternating-current circuit-breakers-Incorporates Amendment 1: 2002 and Amendment 2: 2006; Incorporating corrigendum November 2006 |
|
CENELEC EN 62271-202 |
High-voltage switchgear and controlgear - Part 202: High voltage/low voltage prefabricated substation |
|
CEN EN 62317-7 |
Ferrite cores - Dimensions Part 7: EER-cores-IEC 62317-7: 2005 |
|
CENELEC EN 62317-8 |
Ferrite cores - Dimensions Part 8: E-cores |
|
CEN EN 62317-9 |
Ferrite cores - Dimensions Part 9: Planar cores-Incorporates Amendment A1:March 2007 |
|
CENELEC EN 62333-2 |
Noise suppression sheet for digital devices and equipment Part 2: Measuring methods-IEC 62333-2:2006 |
|
CENELEC EN 62339-1 |
Modular component interfaces for surface-mount fluid distribution components - Part 1: Elastomeric seals |
|
CENELEC EN 62358 |
Ferrite cores Standard inductance factor (AL) and its tolerance-IEC 62358:2004 |
|
CEN EN 629-1 |
Transportable Gas Cylinders - 25E Taper Thread for Connection of Valves to Gas Cylinders - Part 1: Specification |
|
CEN EN 68/A1 |
AMD 1 Hand Held (Portable) Power Driven Grinding Machines: Mechanical Safety |
|
CEN EN 733 |
End-Suction Centrifugal Pumps, Rating with 10 Bar with Bearing Bracket - Nominal Duty Point, Main Dimensions, Designation System |
|
CEN EN 738-3 |
Pressure regulators for use with medical gases - Part 3: Pressure regulators integrated with cylinder valves-Includes amendment A1: 2002 |
|
CEN EN 744 |
Plastics Piping and Ducting Systems - Thermoplastics Pipes - Test Method for Resistance to External Blows by the Round-the- Clock Method |
|
CEN EN 761 |
Plastics Piping Systems - Glass-Reinforced Thermosetting Plastics (GRP) Pipes - Determination of the Creep Factor Under Dry Conditions |
|
CEN EN 88-1 |
Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 500 mbar |
|
CEN EN 922 |
Plastics Piping and Ducting Systems - Pipes and Fittings of Unplasticized Poly(Vinyl Chloride) (PVC-U) - Specimen Preparation for Determination of the Viscosity Number and Calculation of the K-Value |
|
CEN EN 976-1 |
Underground Tanks of Glass-Reinforced Plastics (GRP) - Horizontal Cylindrical Tanks for the Non-Pressure Storage of Liquid Petroleum Based Fuels - Part 1: Requirements and Test Methods for Single Wall Tanks |
|
CEN EN ISO 10286 |
Gas cylinders - Terminology |
|
CEN EN ISO 10447 |
Resistance welding - Peel and chisel testing of resistance spot and projection welds |
|
CEN EN ISO 10564 |
Soldering and Brazing Materials - Methods for the Sampling of Soft Solders for Analysis-ISO 10564: 1993 |
|
CEN EN ISO 10882-2 |
Health and Safety in Welding and Allied Processes - Sampling of Airborne Particles and Gases in the Operator´s Breathing Zone - Part 2: Sampling of Gases-ISO 10882-2:2000 |
|
CEN EN ISO 11623 |
Transportable Gas Cylinders - Periodic Inspection and Testing of Composite Gas Cylinders-ISO 11623: 2002 |
|
CEN EN ISO 12224-1 |
Solder Wire, Solid and Flux Cored - Specification and Test Methods - Part 1: Classification and Performance Requirements-ISO 12224-1:1997 |
|
CEN EN ISO 12224-2 |
Flux Cored Solder Wire - Specification and Test Methods - Part 2: Determination of Flux Content-ISO 12224-2:1997 |
|
CEN EN ISO 13760 |
Plastics Pipes for the Conveyance of Fluids Under Pressure - Miner´s Rule - Calculation Method for Cumulative Damage-ISO 13760:1998 |
|
CEN EN ISO 13769 |
Gas cylinders - Stamp marking |
|
CEN EN ISO 13846 |
Plastics Piping Systems - End-Load-Bearing and Non-End-Load-Bearing Assemblies and Joints for Thermoplastic Pressure Piping - Test Method for Long-Term Leaktightness Under Internal Pressure-ISO 13846:2000 |
|
CEN EN ISO 14246 |
Transportable Gas Cylinders - Gas Cylinder Valves - Manufacturing Tests and Inspections-ISO 14246: 2001 |
|
CEN EN ISO 14323 |
Resistance spot welding and projection welds - Destructive testing of welds - Specimen dimensions and procedure for impact shear test and cross-tension testing-ISO 14323:2006 |
|
CEN EN ISO 14327 |
Resistance welding - Procedures for determining the weldability lobe for resistance spot, projection and seam welding-ISO 14327:2004 |
|
CEN EN ISO 14587 |
Hexalobular Socket Raised Countersunk (Oval) Head Tapping Screws-ISO 14587:2001 |
|
CEN EN ISO 1460 |
Metallic Coatings - Hot Dip Galvanized Coatings on Ferrous Materials - Gravimetric Determination of the Mass per Unit Area (ISO 1460:1992) |
|
CEN EN ISO 14744-1 |
Welding - Acceptance Inspection of Electron Beam Welding Machines - Part 1: Principles and Acceptance Conditions-ISO 14744-1:2000 |
|
CEN EN ISO 14744-2 |
Welding - Acceptance Inspection of Electron Beam Welding Machines - Part 2: Measurement of Accelerating Voltage Characteristics-ISO 14744-2:2000 |
|
CEN EN ISO 14744-6 |
Welding - Acceptance Inspection of Electron Beam Welding Machines - Part 6: Measurement of Stability of Spot Position-ISO 14744-6:2000 |
|
CEN EN ISO 1482 |
Slotted Countersunk (Flat) Head Tapping Screws (Common Head Style) (ISO 1482:1983) |
|
CEN EN ISO 14924 |
Thermal spraying - Post-treatment and finishing of thermally sprayed coatings-ISO 14924: 2005 |
|
CEN EN ISO 15065 |
Countersinks for countersunk head screws with head configuration in accordance with ISO 7721-ISO 15065:2005 |
|
CEN EN ISO 15245-1 |
Gas cylinders Parallel threads for connection of valves to gas cylinders Part 1: specification-ISO 15245-1: 2001 |
|
CEN EN ISO 15483 |
Cross Recessed Raised Countersunk Head Drilling Screws with Tapping Screw Thread-ISO 15483:1999 |
|
CEN EN ISO 15494 |
Plastics piping systems for industrial applications Polybutene (PB), polyethylene (PE) and polypropylene (PP) Specifications for components and the system Metric series-ISO 15494: 2003 |
|
CEN EN ISO 15614-7 |
Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 7: Overlay welding |
|
CEN EN ISO 15618-2 |
Qualification Testing of Welders for Under-Water Welding - Part 2: Diver-Welders and Welding Operators for Hyperbaric Dry Welding-ISO 15618-2:2001 |
|
CEN EN ISO 15876-3 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 3: Fittings-ISO 15876-3:2003 |
|
CEN EN ISO 15876-5 |
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 5: Fitness for purpose of the system-ISO 15876-5:2003 |
|
CEN EN ISO 15877-1 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General-ISO 15877-1:2003 |
|
CEN EN ISO 15877-2 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes-ISO 15877-2:2003 |
|
CEN EN ISO 15877-5 |
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system-ISO 15877-5 |
|
CEN EN ISO 15973 |
Closed End Blind Rivets with Break Pull Mandrel and Protruding Head - AIA/St-ISO 15973: 2000 |
|
CEN EN ISO 15976 |
Closed end blind rivets with break pull mandrel and protrudiing head - St/St-ISO 15976: 2002 |
|
CEN EN ISO 15978 |
Open end blind rivets with break pull mandrel and countersunk head AIA/St-ISO 15978:2002 |
|
CEN EN ISO 15981 |
Open end blind rivets with break pull mandrel and protruding head AIA/AIA-ISO 15981:2002 |
|
CEN EN ISO 16585 |
Closed end blind rivets with pull mandrel and protruding head - A2/SSt-ISO 16585:2002 |
|
CEN EN ISO 1746 |
Rubber or Plastics Hoses and Tubing - Bending Tests-Supersedes EN 21746:1993; ISO 1746:1998, Including Technical Corrigendum 1:1999 |
|
CEN EN ISO 17633 |
Welding consumables - Tubular cored electrodes and rods for gas shielded and non-gas shielded metal arc welding of stainless and heat-resisting steels - Classification-ISO 17633:2004;:1999 |
|
CEN EN ISO 17657-3 |
Resistance welding - Welding current measurement for resistance welding - Part 3: Current sensing coil |
|
CEN EN ISO 18276 |
Welding consumables - Tubular cored electrodes for gasshielded and non-gas-shielded metal arc welding of highstrength steels - Classification-ISO 18276:2005;:2000 |
|
CEN EN ISO 18278-1 |
Resistance welding - Weldability - Part 1: Assessment of weldability for resistance spot, seam and projection welding of metallic materials-ISO 18278-1:2004 |
|
CEN EN ISO 22825 |
Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys-ISO 22825: 2006 |
|
CEN EN ISO 2503 |
Gas Welding Equipment - Pressure Regulators for Gas Cylinders Used in Welding, Cutting and Allied Processes up to 300 Bar-Incorporates Corrigendum December 1998; Supersedes EN 585: 1994; ISO 2503: 1998 |
|
CEN EN ISO 2505 |
Thermoplastics pipes - Longitudinal reversion - Test method and parameters-(ISO 2505): 2005;:1994 |
|
CEN EN ISO 4023 |
Rubber Hoses for Steam - Test Methods (ISO 4023:1991) |
|
CEN EN ISO 4027 |
Hexagon socket set screws with cone point-ISO 4027: 2003 |
|
CEN EN ISO 4526 |
Metallic coatings - Electroplated coatings of nickel for engineering purposes |
|
CEN EN ISO 5183-1 |
Resistance Welding Equipment - Electrode Adaptors, Male Taper 1:10 - Part 1: Conical Fixing, Taper 1:10-Supersedes EN 25183-1:1991; ISO 5183-1:1998 |
|
CEN EN ISO 5183-2 |
Resistance Spot Welding - Electrode Adaptors, Male Taper 1:10 - Part 2: Parallel Shank Fixing for End-Thrust Electrodes-ISO 5183-2:2000; Supersedes EN 25183-2:1991 |
|
CEN EN ISO 6103 |
Bonded abrasive products - Permissible unbalances of grinding wheels as delivered - Static testing-ISO 6103:2005 |
|
CEN EN ISO 6412-3 |
Technical Drawings - Simplified Representation of Pipelines - Part 3: Terminal Features of Ventilation and Drainage Systems (ISO 6412-3 : 1993) |
|
CEN EN ISO 7048 |
Cross Recessed Cheese Head Screws-Corrected 98-09-10; ISO 7048:1998 |
|
CEN EN ISO 8205-1 |
Water-Cooled Secondary Connection Cables for Resistance Welding - Part 1: Dimensions and Requirements for Double-Conductor Connection Cables-ISO 8205-1: 2002 |
|
CEN EN ISO 8308 |
Rubber and plastics hoses and tubing - Determination of transmission of liquids through hose and tubing walls |
|
CEN EN ISO 8662-12 |
Hand-Held Portable Power Tools - Measurement of Vibrations at the Handle - Part 12: Saws and Files with Reciprocating Action and Saws with Oscillating or Rotating Action-ISO 8662-12: 1997 |
|
CEN EN ISO 8739 |
Grooved Pins - Full-Length Parallel Grooved, with Pilot-ISO 8739:1997; Supersedes EN 28739:1992 |
|
CEN EN ISO 9222-1 |
Technical Drawings - Seals for Dynamic Application - Part 1: General Simplified Representation (ISO 9222-1 : 1989) |
|
CEN EN ISO 9455-13 |
Soft Soldering Fluxes - Test Methods - Part 13: Determination of Flux Spattering-ISO 9455-13: 1996 |
|
CEN EN ISO 9455-15 |
Soft Soldering Fluxes - Test Methods - Part 15: Copper Corrosion Test-ISO 9455-15: 1996 |
|
CEN EN ISO 9455-2 |
Soft Soldering Fluxes - Test Methods - Part 2: Determination of Non-Volatile Matter, Ebulliometric Method (ISO 9455-2 : 1993) |
|
CEN ENV 1046 |
Plastics Piping and Ducting Systems - Systems Outside Building Structures for the Conveyance of Water or Sewage - Practices for Installation Above and Below Ground-Ratified European Text:7/05/2001 |
|
CEN ENV 1329-2 |
Plastic Piping Systems for Soil and Waste Discharge (Low and High Temperature) within the Building Structure - Unplasticized Poly(Vinyl Chloride) (PVC-U) - Part 2: Guidance for the Assessment of Conformity |
|
CEN ENV 13550 |
Advanced Manufacturing Technology - Systems Architecture - Enterprise Model Execution and Integration Services-Ratified European Text |
|
CEN ENV 1453-2 |
Plastics Piping Systems with Structured Wall Pipes for Soil and Waste Discharge (Low and High Temperature) Inside Buildings - Unplasticized Poly(Vinyl Chloride)(PVC-U) - Part 2: Guidance for the Assessment of Conformity |
|
CEN ENV 1519-2 |
Plastics Piping Systems for Soil and Waste Discharge (Low and High Temperature) within the Building Structure - Polyethylene (PE) - Part 2: Guidance for the Assessment of Conformity |
|
CEN ENV 1565-2 |
Plastics Piping Systems for Soil and Waste Discharge (Low and High Temperature) within the Building Structure - Styrene Copolymer Blends (SAN+PVC) - Part 2: Guidance for the Assessment of Conformity |
|
CENELEC HD 109.2 S1 |
Miniature Fuses Part 2: Cartridge Fuse-Links |
|
CENELEC HD 187 S4 |
A.C Metal-Enclosed Switchgear and Controlgear for Rated Voltages above 1KV and up to and Including 72.5 KV |
|
CENELEC HD 196 |
Plugs, Sockets - Outlets and Couplers for Industrial Purposes |
|
CENELEC HD 201 S2 |
Sealed Nickel-Cadmium Cylindrical Rechargeable Single Cells |
|
CENELEC HD 211.1 S6 |
Primary Batteries - Part 1: General-Superseded by EN 60 086-1: 1995 |
|
CENELEC HD 22.6 S2/A1 |
AMD 1 Rubber Insulated Cables of Rated Voltages up to and Including 450/750 V Part 6: Arc Welding Cables |
|
CENELEC HD 24 |
No - Load Voltage of Arc - Welding Equipment |
|
CENELEC HD 278 S1 |
Safety of Household and Similar Electrical Appliances - Part 2: Particular Requirements for Room Heaters-Superseded by EN 60335-2-30: 1992 |
|
CENELEC HD 280.2 S1 |
Safety Requirements for Electric Fans and Regulators Part 2: Fans and Regulators for Use in Ships |
|
CENELEC HD 302 |
Transistorized Ballast for Fluorescent Lamps |
|
CENELEC HD 307.3.11 S1 |
Specification for Solventless Polymerisable Resinous Compounds Used for Electrical Insulation Part 3: Specification for Individual Materials Sheet 11: Epoxy Resin- Based Coating Powders |
|
CENELEC HD 307.3.5 S1 |
Specification for Solventless Polymerisable Resinous Compounds Used for Electrical Insulation Part 3: Specifications for Individual Materials Sheet 5: Unsaturated Polyester Impregnating Resins |
|
CENELEC HD 309.1 |
Class 2 Direct Connected Alternating-Current Watthour Meters Part I |
|
CENELEC HD 347 |
Mechanical Vibration of Certain Rotating Electrical Machinery with Shaft Heights Between 80 and 400 mm Measurement and Evaluation of the Vibration Severity |
|
CENELEC HD 352.2 |
Specification for Insulating Materials Based on Built-up Mica or Treated Mica Paper Part 2: Methods of Test |
|
CENELEC HD 352.3.1 S2 |
Specification for Insulating Materials Based on Mica-Part 3: Specifications for Individual Materials. Sheet One: Commutator Separators and Materials |
|
CENELEC HD 358 S2 |
Gas-Insulated Metal- Enclosed Switchgear for Rated Voltages of 72.5 kV and Above |
|
CENELEC HD 362 |
Safety Rules for the Construction of Equipment for Electric Arc Welding and Allied Processes |
|
CENELEC HD 362/A1 |
AMD 1 Safety Rules for the Construction of Equipment for Electric Arc Welding and Allied Processes |
|
CENELEC HD 381 |
Methods of Test for the Determination of Ionic Impurities in Electrical Insulating Materials by Extraction with Liquids |
|
CENELEC HD 390 S2 |
Inductive Voltage Dividers |
|
CENELEC HD 398.1 |
Power Transformers Part 1: General |
|
CENELEC HD 398.2 |
Power Transformers Part 2: Temperature Rise-Superseded by EN 60076-2: 1997 |
|
CENELEC HD 398.3 |
Power Transformers Insulation Levels and Dielectric Tests-Superseded by EN 60076-3:2001 |
|
CENELEC HD 398.3 SI PRAA |
AMD prAA Power Transformers - Part 3: Insulation Levels and Dielectric Tests |
|
CENELEC HD 398.4 |
Power Transformers Part 4: Tappings and Connections |
|
CENELEC HD 400.2 |
Hand-Held Motor Operated Tools Part II: Particular Specifications Sections A to G (CEE 20, Part II, Sections A to G, Modified) |
|
CENELEC HD 400.3N S2 |
Hand-Held Motor Operated Tools Part II: Particular Specifications Section N: Hedge Trimmers and Scissor-Type Grass Shears-Partly Superseded by EN 50 144-2-15: 1997 |
|
CENELEC HD 400.3O S1 |
Hand-Held Motor Operated Tools Part II: Particular Specifications Section O: Routers-Supersedes EN 50144-2-17 |
|
CENELEC HD 42.1 S3 |
Basic Dimensions of Winding Wires - Part 1: Diameters of Conductors for Round Winding Wires |
|
CENELEC HD 42.4 |
Basic Dimensions of Winding Wires Part 4: Diameters of Conductors for Round Resistance Wires |
|
CENELEC HD 420 S2 |
Control Switches (Low Voltage Switching - Devices for Control and Auxiliary Circuit, Including Contactor Relays) |
|
CENELEC HD 422 |
Low-Voltage Air-Break Switches, Air-Break Disconnectors, Air-Break Switch-Disconnectors and Fuse-Combination Units |
|
CENELEC HD 424 |
Specification for High- Voltage Fuse-Links for Motor Circuit Applications |
|
CENELEC HD 426.1 S1 |
Specification for Ceramic and Glass Insulating Materials - Part 1: Definitions and Classification |
|
CENELEC HD 426.2 S1 |
Specification for Ceramic and Glass Insulating Materials - Part 2: Methods of Test |
|
CENELEC HD 428 |
Three-Phase Oil-Immersed Public Distribution Transformers, 50 Hz, from 50 to 2500 kVA, with Highest Voltage for Equipment Not Exceeding 24 kV |
|
CENELEC HD 428/A1 |
AMD 1 Three-Phase Oil-Immersed Public Distribution Transformers, 50 Hz, from 50 to 2500 kVA, with Highest Voltage for Equipment Not Exceeding 24 kV |
|
CENELEC HD 433 |
Safety Requirements for Arc Welding Equipment Coupling Devices for Welding Cables |
|
CENELEC HD 448 S2 |
Common Clauses for High- Voltage Switchgear and Controlgear Standards |
|
CENELEC HD 465.1 |
Lead - Acid Traction Batteries Part 1: General Requirements and Methods of Test |
|
CENELEC HD 465.2 S1 |
Lead-Acid Traction Batteries-Part 2: Dimensions of Cells and Terminals and Marking of Polarity on Cells |
|
CENELEC HD 475 S1 |
Dimensions of Planchets Used in Nuclear Electronic Instruments |
|
CENELEC HD 486 S1 |
Test Method for Evaluating the Oxidation Stability of Hydrocarbon Insulating Liquids-Superseded by EN 61125:1993 |
|
CENELEC HD 496 S1 |
Insulating Foam-Filled Tubes and Solid Rods for Live Working |
|
CENELEC HD 516 S1/A3 |
AMD 3 Guide to Use of Low Voltage Harmonized Cables |
|
CENELEC HD 516 S1/A6 |
AMD 6 Guide to Use of Low Voltage Harmonized Cables |
|
CENELEC HD 523.3.100 TO 105 S1 |
Specification for Flexible Insulating Sleeving Part 3: Specification Requirements for Individual Types of Sleeving Sheets 100 to 105: Extruded PVC Sleeving |
|
CENELEC HD 523.3.406 TO 408 S1 |
Specification for Flexible Insulating Sleeving Part 3: Specification Requirements for Individual Types of Sleeving Sheets 406 to 408: Glass Textile Sleeving with PVC Based Coating-Superseded by EN 60684-3-406 to 408 |
|
CENELEC HD 53.12 |
Rotating Electrical Machines Part 12: Starting Performance of Single-Speed Three-Phase Cage Induction Motors for Voltages up to and Including 660 V, 50 Hz |
|
CENELEC HD 53.4 S2 |
Rotating Electrical Machines-Part 4: Methods for Determining Synchronous Machine Quantities from Tests |
|
CENELEC HD 530.2 S1 |
Controllers with Analogue Signals for Use in Industrial - Process Control Systems Part 2: Guidance for Inspection and Routine Testing |
|
CENELEC HD 540.2 S1 |
Insulation Co-Ordination Part 2: Application Guide |
|
CENELEC HD 541 S1 |
Methods of Test for the Determination of the Ignitability of Solid Electrical Insulating Materials When Exposed to Electrically Heated Wire Sources |
|
CENELEC HD 543.1 S1 |
Performance and Testing of Teleprotection Equipment of Power Systems Part 1: Narrow- Band Command Systems |
|
CENELEC HD 548.3 S1 |
Instrument Transformers Part 3: Combined Transformers |
|
CENELEC HD 553 S2 |
Current Transformers |
|
CENELEC HD 555.0.1 S1 |
Specifications for Particular Types of Winding Wires Part 0: General Requirements Section 1 - Enamelled Round Copper Wire |
|
CENELEC HD 555.0.2 S1 |
Specifications for Particular Types of Winding Wires Part 0: General Requirements Section 2: Enamelled Rectangular Copper Wire |
|
CENELEC HD 555.15 S1 |
Specifications for Particular Types of Winding Wires Part 15: Polyesterimide Enamelled Round Aluminium Winding Wire, class 180 |
|
CENELEC HD 555.21 S2 |
Specifications for Particular Types of Winding Wires Part 21: Solderable Polyurethane Enamelled Round Copper Wire Overcoated with Polyamide, Class 155 |
|
CENELEC HD 555.23 S1 |
Specifications for Particular Types of Winding Wires Part 23: Solderable Polyester (Imide) Enamelled Round Copper Winding Wire, Class 180 |
|
CENELEC HD 555.23 S2 |
Specifications for Particular Types of Winding Wires Part 23: Solderable Polyesterimide Enamelled Round Copper Wire, Class 180 |
|
CENELEC HD 555.25 S1 |
Specifications for Particular Types of Winding Wires Part 25: Polyester (Imide) Overcoated with Polyamide- Imide Enamelled Round Aluminium Winding Wire, Class 200 |
|
CENELEC HD 555.3 S1 |
Specifications for Particular Types of Winding Wires Part 3: Polyester Enamelled Round Copper Wire, Class 155-Superseded by EN 60317-3: 1994 |
|
CENELEC HD 555.32 S1 |
Specifications for Particular Types of Winding Wires Part 32: Glass-Fibre Wound, Polyester or Polyesterimide Varnish-Treated, Bare or Enamelled Rectangular Copper Wire, Temperature Index 155-Superseded by EN 60 317-32:1996 |
|
CENELEC HD 555.7 S1 |
Specifications for Particular Types of Winding Wires Part 7: Polyimide Enamelled Round Copper Winding Wire, Class 220 |
|
CENELEC HD 555.8 S1 |
Specifications for Particular Types of Winding Wires Part 8: Polyesterimide Enamelled Round Copper Winding Wire, Class 180 |
|
CENELEC HD 555.8 S2 |
Specifications for Particular Types of Winding Wires Part 8: Polyesterimide Enamelled Round Copper Wire, Class 180 |
|
CENELEC HD 558 S1 |
Economic Optimisation of Power Cable Size |
|
CENELEC HD 60269-3 |
Low-voltage fuses - Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F |
|
CENELEC HD 618 S1 |
General Classification of Insulating Liquids |
|
CENELEC HD 621 S1 |
Medium voltage impregnated paper insulated distribution cables |
|
CENELEC HD 627 S1 |
Multicore and Multipair Cable for Installation Above and Below Ground |
|
CENELEC HD 627 S1/A1 |
Multicore and Multipair Cable for Installation Above and Below Ground |
|
CENELEC HD 65.1 S1 |
Lamp Caps and Holders Together with Gauges for the Control of Interchangeability and Safety Part 1: Lamp Caps-Superseded by EN 60061-1; Superseded by EN 60061-3:1993 |
|
CENELEC HD 93.2 |
Part 2: Electrical Equipment of Machines Used in Large Series Production Lines |
|
CENELEC ROBT-005 |
Information Concerning Plugs for Household Appliances Covered by CLC/TC 61 Used in the Various CENELEC Countries |