|
CENELEC EN 61951-2 |
Secondary cells and batteries containing alkaline or other non-acid electrolytes Portable sealed rechargeable single cells Part 2: Nickel-metal hydride-IEC 61951-2: 2003; Supersedes EN 61436:1998, EN 61808:2000 & EN 61951-2:2001 |
|
CEN EN 681-1 |
Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber-Includes Amendments A1:1998 and A2:2002; Incorporating Corrigendum August 2002; Includes Amendment A3: 2005 |
|
CEN EN ISO 1478 |
Tapping Screws Thread-ISO 1478: 1999 |
|
CEN EN ISO 3834-4 |
Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements-ISO 3834-4:2005; Supersedes EN 729-4:1994 |
|
CEN EN 10255 |
Non-Alloy steel tubes suitable for welding and threading - Technical delivery conditions-Incorporates Amendment A1:2007 |
|
CEN EN 20898-7 |
Mechanical Properties of Fasteners - Part 7: Torsional Test and Minimum Torques for Bolts and Screws with Nominal Diameters 1 mm to 10 mm (ISO 898-7: 1992) |
|
CEN EN 286-2 |
Simple Unfired Pressure Vessels Designed to Contain Air or Nitrogen: Part 2: Pressure Vessels for Air Braking and Auxiliary Systems for Motor Vehicles and Their Trailers |
|
CENELEC EN 60079-28 |
Explosive atmospheres - Part 28: Protection of equipment and transmission systems using optical radiation |
|
CENELEC EN 60598-2-22 |
Luminaires - Part 2-22: Particular Requirements - Luminaires for Emergency Lighting-Amendment A1:2003; Incorporating Corrigenda December 2005 and October 2007 |
|
CENELEC EN 60947-7-2 |
Low-voltage switchgear and controlgear Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors-IEC 60947-7-2:2002 |
|
CENELEC EN 60998-2-1 |
Connecting Devices for Low Voltage Circuits for Household and Similar Purposes Part 2-1: Particular Requirements for Connecting Devices as Separate Entities with Screw-Type Clamping Units-IEC 60998-2-1:2002, Modified |
|
CENELEC EN 61310-2 |
Safety of Machinery Indication, Marking and Actuation Part 2: Requirements for Marking (IEC 1310-2 : 1995) |
|
CEN EN ISO 13706 |
Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers-ISO 13706:2005 |
|
CEN EN ISO 15610 |
Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables-Supersedes EN 288-5:1994; ISO 15610:2003 |
|
CEN EN ISO 15612 |
Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure-ISO 15612:2004 |
|
CEN EN ISO 3269 |
Fasteners - Acceptance Inspection-ISO 3269:2000 |
|
CEN EN ISO 9692-1 |
Welding and allied processes Recommendations for joint preparation Part 1: Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels-ISO 9692-1: 2003; |
|
CEN EN 13160-1 |
Leak detection systems - Part 1: General principles |
|
CEN EN 13480-2 |
Metallic Industrial Piping - Part 2: Materials |
|
CEN EN 14511-1 |
Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 1: Terms and definitions |
|
CEN EN 288-9 |
Specification and Approval of Welding Procedures for Metallic Materials - Part 9: Welding Procedure Test for Pipeline Welding on Land and Offshore Site Butt Welding of Transmission Pipelines |
|
CEN EN 298 |
Automatic gas burner control systems for gas burners and gas burning appliances with or without fans |
|
CENELEC EN 60598-2-4 |
Luminaires Part 2: Particular Requirements Section 4: Portable General Purpose Luminaires-IEC 60598-2-4:1997 |
|
CENELEC EN 60617-3 |
Graphical Symbols for Diagrams Part 3: Conductors and Connecting Devices-IEC 617-3: 1996 |
|
CENELEC EN 60947-4-2 |
Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters-Includes amendment A1: March 2002; Amendment 2: December 2006 |
|
CENELEC EN 61346-2 |
Industrial Systems, Installations and Equipment and Industrial Products Structuring Principles and Reference Designations Part 2: Classification of Objects and Codes for Classes-IEC 61346-2:2000 |
|
CEN EN ISO 13337 |
Spring-Type Straight Pins - Slotted, Light Duty-ISO 13337: 1997 |
|
CEN EN ISO 14343 |
Welding consumables - Wire electrodes, strip electrodes, wires and rods for fusion welding of stainless and heat resisting steels - Classification |
|
CEN EN ISO 2702 |
Heat-Treated Steel Tapping Screws - Mechanical Properties (ISO 2702 : 1992) |
|
CEN EN ISO 7045 |
Pan Head Screws with Type H or Type Z Cross Recess - Product Grade A (ISO 7045:1994) |
|
CEN EN 1011-8 |
Welding - Recommendations for welding of metallic materials - Part 8: Welding of cast irons |
|
CENELEC EN 50083-2 |
Cable networks for television signals, sound signals and interactive services Part 2: Electromagnetic compatibility for equipment |
|
CENELEC EN 50121-3-2 |
Railway applications - Electromagnetic compatibility Part 3-2: Rolling stock - Apparatus |
|
CENELEC EN 60127-3 |
Miniature fuses Part 3: Sub-miniature fuse-links-Includes amendment A2:2003; IEC 60127-3:1988 + A1:1991 + A2:2002 |
|
CENELEC EN 60204-32 |
Safety of Machinery - Electrical Equipment of Machines Part 32: Requirements for Hoisting Machines-IEC 60204-32:1998 |
|
CENELEC EN 60216-1 |
Electrical Insulating Materials - Properties of Thermal Endurance Part 1: Ageing Procedures and Evaluation of Test Results-IEC 60216-1:2001 |
|
CENELEC EN 62040-3 |
Uninterruptible Power Systems (UPS) - Part 3: Method of Specifying the Performance and Test Requirements-Supersedes ENV 50091-3:1998; IEC 62040-3:1999, Modified |
|
CEN EN ISO 11688-1 |
Acoustics - Recommended Practice for the Design of Low-Noise Machinery and Equipment - Part 1: Planning-ISO/TR 11688-1:1995 |
|
CEN EN ISO 1234 |
Split Pins-ISO 1234:1997 |
|
CEN EN ISO 4759-3 |
Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C-ISO 4759-3:2000 |
|
CEN EN ISO 8502-6 |
Preparation of Steel Substrates Before Application of Paints and Related Products - Tests for the Assessment of Surface Cleanliness - Part 6: Extraction of Soluble Contaminants for Analysis - The Bressle Method-ISO 8502-6: 2006 |
|
CEN EN 12474 |
Cathodic Protection of Submarine Pipelines |
|
CEN EN 13906-2 |
Cylindrical Helical Springs Made from Round Wire and Bar - Calculation and Design - Part 2: Extension Springs |
|
CEN EN 14399-4 |
High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
|
CEN EN 1834-2 |
Reciprocating Internal Combustion Engines - Safety Requirements for Design and Construction of Engines for Use in Potentially Explosive Atmospheres - Part 2: Group I Engines for Use in Underground Workings Susceptible to Firedamp and/or Combustible Dust |
|
CENELEC EN 60034-16-1 |
Rotating Electrical Machines Part 16: Excitation Systems for Synchronous Machines Chapter 1: Definitions (IEC 34-16-1 : 1991 + Corrigendum 1992) |
|
CENELEC EN 60034-18-22 |
Rotating Electrical Machines Part 18-22: Functional Evaluation of Insulation Systems - Test Procedures for Wire-Wound Windings - Classification of Changes and Insulation Component Substitutions-IEC 60034-18-22:2000 |
|
CENELEC EN 60086-4 |
Primary Batteries Part 4: Safety Standard for Lithium Batteries-IEC 60086-4: 2000 |
|
CENELEC EN 60742 |
Isolating Transformers and Safety Isolating Transformers Requirements-IEC 742 : 1983 + A1 : 1992, Modified; Partly Superseded by EN 61558-1: 1997, EN 61558-2-4: 1997, EN 61 558-2-6: 1997 and EN 61 558-2-7: 1997 |
|
CENELEC EN 61204 |
Low-Voltage Power Supply Devices, d.c. Output - Performance Characteristics-Includes Amendment A1: 2001; IEC 61204: 1993, Modified + A1: 2001 |
|
CENELEC EN 61347-2-3 |
Lamp controlgear Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps-Includes amendment A1:2004; IEC 61347-2-3:2000 + A1:2004; Supersedes EN 60928:1995; Corr July 2003; A1:September 2004; A2: February 2006 |
|
CENELEC EN 61400-1 |
Wind turbines Part 1: Design requirements-IEC 61400-1: 2005 |
|
CEN EN 736-3 |
Valves - Terminology - Part 3: Definition of terms-Including amendment A1: 2001 |
|
CEN EN 792-8 |
Hand-Held Non-Electric Power Tools - Safety Requirements - Part 8: Sanders and Polishers |
|
CEN EN ISO 10511 |
Prevailing Torque Type Hexagon Thin Nuts (with Non-Metallic Insert)-ISO 10511:1997 |
|
CEN EN ISO 1307 |
Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses |
|
CEN EN ISO 4029 |
Hexagon socket set screws with cup point-ISO 4029:2003 |
|
CEN EN ISO 6520-2 |
Welding and Allied Processes - Classification of Geometric Imperfections in Metallic Materials - Part 2: Welding with Pressure-ISO 6520-2:2001 |
|
CEN EN ISO 6945 |
Rubber Hoses - Determination of Abrasion Resistance of the Outer Cover-Includes Amendment A1:2000; ISO 6945:1991 + A1:1998 |
|
CEN EN ISO 8249 |
Welding - Determination of Ferrite Number (FN) in Austenitic and Duplex Ferritic-Austenitic Cr-Ni Stainless Steel Weld Metals-ISO 8249:2000 |
|
CEN EN ISO 9606-2 |
Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys-ISO 9606-2:2004; Supersedes EN 287-2:1992 |
|
CEN EN 13480-3 |
Metallic industrial piping - Part 3: Design and calculation-Includes Amendment A1:2005 |
|
CEN EN 1762 |
Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification |
|
CEN EN 1953 |
Atomizing and Spraying Equipment for Coating Materials - Safety Requirements |
|
CENELEC EN 50260-1 |
Safety of Hand-Held Battery-Powered Motor-Operated Tools and Battery Packs Part 1: General Requirements |
|
CENELEC EN 50342 |
Lead-Acid Starter Batteries - General Requirements, Methods of Test and Numbering-Includes Amendments A1:2001, A2:2001 and A3:2004; Incorporates Corrigendum March 2003; Supersedes EN 60095-1:1993 |
|
CENELEC EN 60034-18-21 |
Rotating Electrical Machines Part 18: Functional Evaluation of Insulation Systems Section 21: Test Procedures for Wire-Wound Windings - Thermal Evaluation and Classification-Includes Amendments A1: 1996 and A2: 1996; IEC 34-18-21: 1992 + A1: 1996 and A2: 1996 |
|
CENELEC EN 60034-18-31 |
Rotating Electrical Machines Part 18: Functional Evaluation of Insulation Systems Section 31: Test Procedures for Form-Wound Windings - Thermal Evaluation and Classification of Insulation Systems Used in Machines up to and Including 50 MVA and 15 kV-Includes Amendment A1: 1996; IEC 34-18-31: 1992 + A1: 1996 |
|
CENELEC EN 60086-2 |
Primary batteries - Part 2: Physical and electrical specifications |
|
CENELEC EN 60099-1 |
Surge Arresters - Part 1: Non-Linear Resistor Type Gapped Surge Arresters for A.C. Systems-Including Amendment A1:1999; IEC 60099-1:1991 + A1:1999 |
|
CENELEC EN 60332-1-1 |
Tests on electric and optical fibre cables under fire conditions Part 1-1: Test for vertical flame propagation for a single insulated wire or cable - Apparatus-IEC 60332-1-1:2004; Partially supersedes EN 50265-1:1998 |
|
CENELEC EN 60439-2 |
Low-Voltage Switchgear and Controlgear Assemblies Part 2: Particular Requirements for Busbar Trunking Systems (Busways)-IEC 60439-2:2000; Amd 1:2005 |
|
CENELEC EN 60598-2-12 |
Luminaires - Part 2-12: Particular requirements - Mains socket-outlet mounted nightlights-Incorporating corrigendum December 2006 |
|
CENELEC EN 60598-2-13 |
Luminaires Part 2-13: Particular requirements - Ground recessed luminaires-Incorporating corrigendum December 2006 |
|
CENELEC EN 60598-2-23 |
Luminaires - Part 2-23: Particular Requirements - Extra Low-Voltage Lighting Systems for Filament Lamps-Includes Amendment A1: 2000; IEC 60598-2-23: 1996 + A1: 2000 |
|
CENELEC EN 60598-2-6 |
Luminaires Part 2: Particular Requirements Section 6: Luminaires with Built-In Transformers or Converters for Filament Lamps-Includes Amendment A1: 1997; IEC 598-2-6: 1994 + A1: 1996 |
|
CENELEC EN 60695-1-1 |
Fire Hazard Testing Part 1-1: Guidance for Assessing the Fire Hazard of Electrotechnical Products - General Guidelines-IEC 60695-1-1: 1999 + Corrigendum 2000 |
|
CENELEC EN 60898-1 |
Electrical accessories - Circuit breakers for overcurrent protection for household and similar installations Part 1: Circuit-breakers for a.c. operation-Including Amendment 1: 08/2004, Amendment 11: 09/2005, Corrigendum 02/2004; IEC 60898-1:2002;:1991 |
|
CENELEC EN 60947-5-3 |
Low-Voltage Switchgear and Controlgear - Part 5-3: Control Circuit Devices and Switching Elements - Requirements for Proximity Devices with Defined Behaviour under Fault Conditions (PDF)-Incorporating Amendment A1: 4/2005 |
|
CENELEC EN 61204-3 |
Low Voltage Power Supplies, D.C. Output Part 3: Electromagnetic Compatibility (EMC)-IEC 61204-3: 2000 |
|
CENELEC EN 61293 |
Marking of Electrical Equipment with Ratings Related to Electrical Supply - Safety Requirements; (IEC 1293 : 1994) |
|
CENELEC EN 61310-3 |
Safety of Machinery - Indication, Marking and Actuation - Part 3: Requirements for the Location and Operation of Actuators-IEC 61310-3: 1999 |
|
CENELEC EN 61558-2-9 |
Safety of power transformers, power supply units and similar products Part 2-9: Particular requirements for transformers for class III handlamps for tungsten filament lamps-IEC 61558-2-9:2002; Supersedes EN 60742:1995 |
|
CENELEC EN 61779-2 |
Electrical Apparatus for the Detection and Measurement of Flammable Gases Part 2: Performance Requirements for Group I Apparatus Indicating a Volume Fraction up to 5% Methane in Air-Supersedes EN 50055:1998; IEC 61779-2:1998 Modified |
|
CENELEC EN 61800-2 |
Adjustable Speed Electrical Power Drive Systems Part 2: General Requirements Rating Specifications for Low Voltage Adjustable Frequency a.c. Power Drive Systems-IEC 61800-2:1998 |
|
CENELEC EN 61800-4 |
Adjustable speed electrical power drive systems Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV-IEC 61800-4: 2002 |
|
CEN EN 692 |
Machine tools - Mechanical presses - Safety |
|
CEN EN 809 |
Pumps and pump units for liquids - Common safety requirements-Incorporating corrigendum February 2001 and corrigendum March 2002 |
|
CEN EN ISO 15547-1 |
Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers-ISO 15547-1: 2005; Supersedes EN ISO 15547: 2001 |
|
CEN EN ISO 4753 |
Fasteners - Ends of Parts with External ISO Metric Screw Thread-ISO 4753: 1999 |
|
CEN EN ISO 7049 |
Cross Recessed Pan Head Tapping Screws (ISO 7049:1983) |
|
CENELEC CLC/TS 60034-25 |
Rotating electrical machines Part 25: Guide for the design and performance of cage induction motors specifically designed for converter supply |
|
CEN EN 10217-3 |
Welded steel tubes for pressure purposes Technical delivery conditions Part 3: Alloy fine grain steel tubes |
|
CEN EN 14399-5 |
High-strength structural bolting assemblies for preloading - Part 5: Plain washers-Including Corrigendum January 2006 |
|
CEN EN 14511-3 |
Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 3: Test methods-Supersedes EN 12055:1998; EN 255-2:1997 and EN 814-2:1997; Incorporating corrigendum December 2004 |
|
CEN EN 14511-4 |
Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 4: Requirements-Supersedes EN 12055:1998, EN 255-4:1997 and EN 814-3:1997 |
|
CEN EN 1947 |
Fire-fighting hoses - Semi-rigid delivery hoses and hose assemblies for pumps and vehicles-Incorporating Amendment A1: 2007 |
|
CEN EN 247 |
Heat Exchangers - Terminology |
|
CENELEC EN 50022 |
Low Voltage Switchgear and Controlgear for Industrial Use Mounting Rails Top Hat Rails 35 mm Wide for Snap-on Mounting of Equipment |
|
CEN EN 60068-2-80 |
Environmental testing Part 2-80: Tests Test Fi: Vibration Mixed mode-IEC 60068-2-80:2005 |
|
CENELEC EN 60204-11 |
Safety of Machinery - Electrical Equipment of Machines - Part 11: Requirements for HV Equipment for Voltages Above 1 000 V A.C. or 1 500 V D.C. and Not Exceeding 36kV-IEC 60204-11: 2000 (F) |
|
CENELEC EN 60204-31 |
Safety of machinery Electrical equipment of machines Part 31: Particular safety and EMC requirements for sewing machines, units and systems-IEC 60204-31:1996, Modified; Supersedes EN 60204-3-1:1990; Incorporating Corrigendum August 2000 |
|
CENELEC EN 60243-1 |
Electrical Strength of Insulating Materials - Test Methods Part 1: Tests at Power Frequencies-IEC 60243-1:1998; Supersedes HD 559.1 S1:1991 |
|
CENELEC EN 60352-3 |
Solderless Connections Part 3: Solderless Accessible Insulation Displacement Connections - General Requirements, Test Methods and Practical Guidance (IEC 352-3: 1993) |
|
CENELEC EN 60694 |
Common specifications for high-voltage switchgear and controlgear standards-Includes Amendments A1:2000 and A2:2001; IEC 60694:1996 + A1:2000 + A2:2001 + Corrigendum 2001 + Corrigendum 2001; Incorporates Corrigenda April 1998 and May 1999 |
|
CENELEC EN 60801-2 |
Electromagnetic Compatibility for Industrial-Process Measurement and Control Equipment Part 2: Electrostatic Discharge Requirements (IEC 801-2:1991) |
|
CENELEC EN 60999-1 |
Connecting Devices - Electrical Copper Conductors Safety Requirements for Screw-Type and Screwless-Type Clamping Units Part 1: General Requirements and Particular Requirements for Clamping Units for Conductors from 0,2 mm2 up to 35 mm2 (Included)-IEC 60999-1:1999 |
|
CENELEC EN 61008-1 |
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB's) Part 1: General rules-Incorporates Amendment A11: 08/2007 |
|
CENELEC EN 61347-2-1 |
Lamp controlgear Part 2-1: Particular requirements for starting devices (other than glow starters)-Includes amendment A1: 3/2006; Incorporating Corrigendum July 2003 and November 2006 |
|
CENELEC EN 61557-1 |
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 1: General requirements |
|
CENELEC EN 61558-2-2 |
Safety of power transformers, power supplies, reactors and similar products - Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers |
|
CENELEC EN 61779-5 |
Electrical Apparatus for the Detection and Measurement of Flammable Gases - Part 5: Performance Requirements for Group II Apparatus Indicating a Volume Fraction Up to 100% Gas-Supersedes EN 50058:1998; IEC 61779-5:1998, Modified |
|
CENELEC EN 62019 |
Electrical Accessories - Circuit-Breakers and Similar Equipment for Household Use - Auxiliary Contact Units-Includes amendments A1:2003 and A11:2005; IEC 62019:1999 + A1:2002 |
|
CENELEC EN 62208 |
Empty enclosures for low-voltage switchgear and controlgear assemblies General requirements-IEC 62208:2002; |
|
CENELEC EN 62271-109 |
High-voltage switchgear and controlgear Part 109: Alternating-current series capacitor by-pass switches |
|
CEN EN ISO 16047 |
Fasteners - Torque/clamp force testing-ISO 16047:2005 |
|
CEN EN ISO 5211 |
Industrial Valves - Part-Turn Actuator Attachments-ISO 5211:2001 |
|
CEN EN ISO 9013 |
Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances-ISO 9013: 2002; Includes Amendment A1:2003 |
|
CEN EN 1248 |
Foundry Machinery - Safety Requirements for Abrasive Blasting Equipment |
|
CEN EN 13480-5 |
Metallic industrial piping - Part 5: Inspection and testing |
|
CEN EN 1679-1 |
Reciprocating Internal Combustion Engines - Safety - Part 1: Compression Ignition Engines |
|
CEN EN 1760-1 |
Safety of Machinery - Pressure Sensitive Protective Devices - Part 1: General Principles for the Design and Testing of Pressure Sensitive Mats and Pressure Sensitive Floors |
|
CENELEC EN 60034-26 |
Rotating electrical machines Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors |
|
CENELEC EN 60076-2 |
Power Transformers Part 2: Temperature Rise-Supersedes HD 398.2 S1: 1980 and Its Amendment; IEC 76-2: 1993, Modified |
|
CENELEC EN 60076-3 |
Power Transformers Part 3: Insulation Levels, Dielectric Tests and External Clearances in Air-IEC 60076-3:2000 + Corrigendum 2000; Supersedes HD 398.3 S1:1986 + A1:1995 |
|
CENELEC EN 60598-2-3 |
Luminaires Part 2-3: Particular requirements - Luminaires for road and street lighting-Incorporating Corrigendum August 2005; IEC 60598-2-3: 2002 |
|
CENELEC EN 60598-2-8 |
Luminaires - Part 2: Particular Requirements - Section 8: Handlamps-Includes Amendment A1:2000; IEC 598-2-8:1996 + A1:2000, Modified |
|
CENELEC EN 60921 |
Ballasts for tubular fluorescent lamps - Performance requirements-Includes Amendment A1; June 2006; IEC 60921:2004 |
|
CENELEC EN 61558-2-13 |
Safety of Power Transformers, Power Supply Units and Similar Devices Part 2-13: Particular Requirements for Auto-Transformers for General Use-IEC 61558-2-13: 1999 |
|
CENELEC EN 61558-2-5 |
Safety of power transformers, power supply units and similar Part 2-5: Particular requirements for shaver transformers and shaver supply units-Includes amendment A11:2004; IEC 61558-2-5:1997; Partly supersedes EN 60742:1995 |
|
CENELEC EN 61558-2-8 |
Safety of Small Power Transformers, Power Supply Units and Similar Part 2-8: Particular Requirements for Bell and Chime Transformers-IEC 61558-2-8:1998; Supersedes EN 60742:1995 |
|
CEN EN 764-1 |
Pressure equipment - Part 1: Terminology - Pressure, temperature, volume, nominal size-Supersedes EN 764:1994 |
|
CEN EN 764-3 |
Pressure Equipment - Part 3: Definition of Parties Involved |
|
CEN EN ISO 4516 |
Metallic and Other Inorganic Coatings - Vickers and Knoop Microhardness Tests-ISO 4516:2002 |
|
CEN EN ISO 7046-2 |
Cross Recessed Countersunk Flat Head Screws (Common Head Style) - Grade A - Part 2: Steel of Property Class 8.8, Stainless Steel and Non-Ferrous Metals (ISO 7046:1994) |
|
CEN EN 10208-1 |
Steel Pipes for Pipelines for Combustible Fluids - Technical Delivery Conditions - Part 1: Pipes of Requirement Class A |
|
CEN EN 12201-2 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes |
|
CEN EN 12639 |
Liquid Pumps and Pump Units - Noise Test Code - Grade 2 and Grade 3 of Accuracy-Incorporating Corrigenda November 2000 and September 2004 |
|
CEN EN 12723 |
Liquid Pumps - General Terms for Pumps and Installations - Definitions, Quantities, Letter Symbols and Units |
|
CEN EN 13218 |
Machine Tools - Safety - Stationary Grinding Machines |
|
CEN EN 13555 |
Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections |
|
CEN EN 14399-1 |
High-strength structural bolting assemblies for preloading - Part 1: General requirements |
|
CEN EN 1555-1 |
Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 1: General |
|
CEN EN 161 |
Automatic Shut-Off Valves for Gas Burners and Gas Appliances |
|
CENELEC EN 50091-1-1 |
Uninterruptible power systems (UPS) Part 1-1: General and safety requirements for UPS used in operator access areas-Incorporating corrigendum August 2004; Supersedes EN 50091-1:1993 |
|
CENELEC EN 50091-1-2 |
Uninterruptible Power Systems (UPS) - Part 1-2: General and Safety Requirements for UPS Used in Restricted Access Locations-Incorporates Corrigendum August 1999; |
|
CEN EN 560 |
Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes-Incorporating corrigendum October 2007 |
|
CENELEC EN 60071-1 |
Insulation Co-Ordination Part 1: Definitions, Principles and Rules |
|
CENELEC EN 60071-2 |
Insulation Co-Ordination Part 2: Application Guide-IEC 71-2: 1996; Supersedes HD 450.2 S1: 1991 and Partly Supersedes HD 540.3 S1: 1991 |
|
CENELEC EN 60216-2 |
Electrical insulating materials Thermal endurance properties Part 2: Determination of thermal endurance properties of electrical insulating materials Choice of test criteria-(IEC 60216-2):2005;:1992 |
|
CENELEC EN 60598-2-9 |
Luminaires Part 2: Particular Requirements Section Nine - Photo and Film Luminaires (Non- Professional) |
|
CENELEC EN 60745-2-15 |
Hand-held motor-operated electric tools - Safety Part 2-15: Particular requirements for hedge trimmers |
|
CENELEC EN 60811-1-1 |
Insulating and Sheathing Materials of Electric and Optical Cables - Common Test Methods - Part 1-1: General Application - Measurement of Thickness and Overall Dimensions - Tests for Determining the Mechanical Properties-Includes Amendment A1: 2001; IEC 60811-1-1: 1993 - A1: 2001; Supersedes HD 505.1-1 S3: 1991 |
|
CENELEC EN 60999-2 |
Connecting devices Electrical copper conductors Safety requirements for screw-type and screwless-type clamping units Part 2: Particular requirements for clamping units for conductors above 35 mm up to 300 mm (included)-IEC 60999:2003 |
|
CENELEC EN 61014 |
Programmes for reliability growth-IEC 61014:2003 |
|
CENELEC EN 61643-21 |
Low Voltage Surge Protective Deveices - Part 21: Surge Protective Devices Connected to Telecommunications and Signalling Networks - Performance Requirements and Testing Methods-IEC 61643-21:2000 + Corrigendum 2001 |
|
CENELEC EN 61951-1 |
Secondary cells and batteries containing alkaline or other non-acid electrolytes - Portable sealed rechargeable single cells Part 1: Nickel-cadmium-IEC 61951-1: 2003; Supersedes HD 561 S1:1991, EN 60285:1994 and EN 61440:1997 |
|
CENELEC EN 62013-1 |
Caplights for use in mines susceptible to firedamp Part 1: General requirements - Construction and testing in relation to the risk of explosion-IEC 62013-1: 2005 |
|
CEN EN 676 |
Automatic forced draught burners for gaseous fuels |
|
CEN EN 856 |
Rubber Hoses and Hose Assemblies - Rubber-Covered Spiral Wire Reinforced Hydraulic Type - Specification |
|
CEN EN ISO 14580 |
Hexalobular socket cheese head screws-Incorporating Technical Corrigendum December 2005; ISO 14580:2001 |
|
CEN EN ISO 15611 |
Specification and qualification of welding procedures for metallic materials Qualification based on previous welding experience-ISO 15611:2003; Supersedes EN 288-6:1994 |
|
CEN EN ISO 2560 |
Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification-Supersedes EN 499:1994; ISO 2560:2002 |
|
CEN EN ISO 7046-1 |
Countersunk Flat Head Screws (Common Head Style) with Type H or Type Z Cross Recess - Product Grade A - Part 1: Steel of Property Class 4.8 (ISO 7046-1:1994) |
|
CEN EN ISO 8674 |
Hexagon Nuts, Style 2, with Metric Fine Pitch Thread - Product Grades A and B-Supersedes EN 28674:1991; ISO 8674:1999 |
|
CENELEC HD 21.2 S2/ A13 |
AMD 13 Polyvinyl Chloride Insulated Cables of Rated Voltages up to and Including 450/750 V Part 2: Test Methods |
|
CEN EN 10226-1 |
Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
|
CEN EN 12201-1 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 1: General |
|
CEN EN 1251-1 |
Cryogenic Vessels - Transportable Vacuum Insulated Vessels of Not More Than 1000 Litres Volume - Part 1: Fundamental Requirements |
|
CEN EN 12954 |
Cathodic Protection of Buried or Immersed Metallic Structures - General Principles and Application for Pipelines |
|
CEN EN 13160-3 |
Leak detection systems - Part 3: Liquid systems for tanks |
|
CEN EN 14730-2 |
Railway applications - Track - Aluminothermic welding of rails - Part 2: Qualification of aluminothermic welders, approval of contractors and acceptance of welds |
|
CEN EN 2591 |
Aerospace Series - Elements of Electrical and Optical Connection - Test Methods - General |
|
CEN EN 28839 |
Mechanical Properties of Fasteners - Bolts, Screws, Studs and Nuts Made of Non-Ferrous Metals |
|
CENELEC EN 50013 |
Low Voltage Switchgear and Controlgear for Industrial Use Terminal Marking and Distinctive Number for Particular Control Switches |
|
CENELEC EN 50128 |
Railway Applications - Communications, Signalling and Processing Systems - Software for Railway Control and Protection Systems |
|
CENELEC EN 50205 |
Relays with Forcibly Guided (Mechanically Linked) Contacts |
|
CENELEC EN 60335-2-51 |
Household and similar electrical appliances Safety Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations-IEC 60335-2-51: 2002 |
|
CENELEC EN 60349-1 |
Electric traction - Rotating electrical machines for rail and road vehicles - Part 1: Machines other than electronic convertor-fed alternating current motors-Includes amendment A1: 2002; IEC 60349-1: 1999 + A1: 2002; Supersedes HD 225 S1: 1977 |
|
CENELEC EN 60745-2-5 |
Hand-held motor-operated electric tools - Safety - Part 2-5: Particular requirements for circular saws |
|
CENELEC EN 60968 |
Self-Ballasted Lamps for General Lighting Services Safety Requirements-Includes Amendments A1:01/1993 and A2:10/1999; IEC 60968:1988 Modified + A1:1991 + A2:1999 |
|
CENELEC EN 61056-1 |
General purpose lead-acid batteries (valve-regulated types) Part 1: General requirements, functional characteristics - Methods of test-IEC 61056-1: 2002 |
|
CENELEC EN 61326-2-2 |
Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-2: Particular requirements Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low-voltage distribution systems-IEC 61326-2-2:2005; Supersedes EN 61326:1997 + A1:1998 + A2:2001 + A3:2003 |
|
CENELEC EN 61400-2 |
Wind turbines Part 2: Design requirements for small wind turbines-IEC 61400-2:2006;:1996 |
|
CENELEC EN 61558-2-12 |
Safety of Power Transformers, Power Supply Units and Similar Devices Part 2-12: Particular Requirements for Constant Voltage Transformers-IEC 61558-2-12:2001 |
|
CENELEC EN 61558-2-23 |
Safety of Power Transformers, Power Supply Units and Similar Devices Part 2-23: Particular Requirements for Transformers for Construction Sites-IEC 61558-2-23: 2000 |
|
CENELEC EN 61558-2-3 |
Safety of Power Transformers, Power Supply Units and Similar Devices Part 2-3: Particular Requirements for Ignition Transformers for Gas and Oil Burners-IEC 61558-2-3: 1999 |
|
CENELEC EN 61960 |
Secondary cells and batteries containing alkaline or other non-acid electrolytes Secondary lithium cells and batteries for portable applications-IEC 61960: 2003; Partially Supersedes EN 61960-1:2001 & EN 61960-2:2001 |
|
CENELEC EN 62041 |
Power transformers, power supply units, reactors and similar products EMC requirements-IEC 62041: 2003 |
|
CENELEC EN 62079 |
Preparation of Instructions - Structuring, Content and Presentation-IEC 62079:2001 |
|
CEN EN 746-2 |
Industrial Thermoprocessing Equipment - Part 2: Safety Requirements for Combustion and Fuel Handling Systems |
|
CEN EN 764-4 |
Pressure equipment - Pressure equipment Part 4: Establishment of technical delivery conditions for metallic materials |
|
CEN EN 792-7 |
Hand-held non-electric power tools Safety requirements Part 7: Grinders-Supersedes EN 68: 1977 |
|
CEN EN ISO 10512 |
Prevailing Torque Type Hexagon Nuts (with Non-Metallic Insert), Style 1, with Metric Fine Pitch Thread - Property Classes 6, 8 and 10-ISO 10512:1997 |
|
CEN EN ISO 14585 |
Hexalobular Socket Pan Head Tapping Screws-ISO 14585: 2001; Including Corrigendum December 2005 |
|
CEN EN ISO 17292 |
Metal ball valves for petroleum, petrochemical and allied industries-ISO 17292:2004 |
|
CEN EN ISO 3613 |
Chromate Conversion Coatings on Zinc, Cadmium, Aluminium-Zinc Alloys and Zinc-Aluminium Alloys - Test Methods-ISO 3613:2000 |
|
CEN EN ISO 6789 |
Assembly tools for screws and nuts Hand torque tools Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure-Supersedes EN 26789:1994; ISO 6789:2003 |
|
CEN EN ISO 7090 |
Plain Washers, Chamfered - Normal Series - Product Grade A-ISO 7090:2000 |
|
CEN EN ISO 7093-1 |
Plain Washers - Large Series - Part 1: Product Grade A-ISO 7093-1:2000 |
|
CEN EN ISO 8434-4 |
Metallic Tube Connections for Fluid Power and General Use - Part 4: 24 Degree Cone Connectors with O-Ring Weld-on Nipples-ISO 8434-4:1995 |
|
CEN EN ISO 8503-1 |
Preparation of Steel Substrates Before Application of Paints and Related Products - Surface Roughness Characteristics of Blast-Cleaned Steel Substrates - Part 1: Specifications and Definitions for ISO Surface Profile Comparators for the Assessment of Abrasive Blast-Cleaned Surfaces (ISO 8503-1 : 1988) |
|
CEN ENV 247 |
Heat Exchangers - Terminology |
|
CENELEC ENV 61400-1 |
Wind Turbine Generator Systems Part 1: Safety Requirements (IEC 1400-1 : 1994)-Superseded by EN 61400-1:02/2004 |
|
CENELEC HD 21.2 S2 |
Polyvinyl Chloride Insulated Cables of Rated Voltages up to and Including 450/750 V - Part 2: Test Methods |
|
CEN EN 1043-2 |
Destructive Tests on Welds in Metallic Materials - Hardness Test - Part 2: Micro Hardness Testing on Welded Joints |
|
CEN EN 12100 |
Plastics Piping Systems - Polyethylene (PE) Valves - Test Method for Resistance to Bending between Supports |
|
CEN EN 1333 |
Flanges and their joints - Pipework components - Definition and selection of PN |
|
CEN EN 13906-3 |
Cylindrical Helical Springs Made from Round Wire and Bar - Calculation and Design - Part 3: Torsion Springs |
|
CEN EN 14420-2 |
Hose fittings with clamp units - Part 2: Hose side parts of hose tail |
|
CEN EN 14879-1 |
Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 1: Terminology, design and preparation of substrate |
|
CEN EN 1600 |
Welding Consumables - Covered Electrodes for Manual Metal Arc Welding of Stainless and Heat Resisting Steels - Classification |
|
CEN EN 1834-1 |
Reciprocating Internal Combustion Engines - Safety Requirements for Design and Construction of Engines for Use in Potentially Explosives Atmospheres - Part 1: Group II Engines for Use in Flammable Gas and Vapour Atmospheres |
|
CEN EN 27286 |
Graphical Symbols for Resistance Welding Equipment |
|
CENELEC EN 50200 |
Method of test for resistance to fire of unprotected small cables for use in emergency circuits |
|
CENELEC EN 50272-3 |
Safety requirements for secondary batteries and battery installations Part 3: Traction batteries |
|
CENELEC EN 50397-1 |
Covered conductors for overhead lines and the related accessories for rated voltages above 1 kV a.c. and not exceeding 36 kV a.c. Part 1: Covered conductors |
|
CENELEC EN 60079-30-1 |
Explosive atmospheres - Part 30-1: Electrical resistance trace heating - General and testing requirements |
|
CENELEC EN 60255-21-1 |
Electrical Relays Part 21: Vibration, Shock, Bump and Seismic Tests on Measuring Relays and Protection Equipment Section 1: Vibration Tests (Sinusoidal) (IEC 255-21-1 : 1988) |
|
CENELEC EN 60332-1-2 |
Tests on electric and optical fibre cables under fire conditions Part 1-2: Test for vertical flame propagation for a single insulated wire or cable - Procedure for 1 kW pre-mixed flame-IEC 60332-1-2:2004; Supersedes EN 50265-2-1:1998 |
|
CENELEC EN 60349-2 |
Railway Applications - Rotating Electrical Machines for Rail and Road Vehicles Part 2: Electronic Convertor-Fed Alternating Current Motors-IEC 60349-2:1993, Modified |
|
CENELEC EN 60598-2-2 |
Luminaires Part 2: Particular Requirements Section 2: Recessed Luminaires-IEC 598-2-2: 1996 including Amendment A1: 1997; Supersedes EN 60598-2-2: 1989 and its Amendment |
|
CENELEC EN 60598-2-5 |
Luminaires Part 2-5: Particular Requirements - Floodlights-IEC 60598-2-5: 1998; Includes Corrigendum December 1998 |
|
CENELEC EN 60745-2-2 |
Hand-held motor-operated electric tools Safety Part 2-2: Particular requirements for screwdrivers and impact wrenches-Incorporates Amendment A11: March 2007 |
|
CENELEC EN 60947-5-6 |
Low-Voltage Switchgear and Controlgear Part 5-6: Control Circuit Devices and Switching Elements DC Interface for Proximity Sensors and Switching Amplifiers (NAMUR)-IEC 60947-5-6:1999; Supersedes EN 50227:1997 |
|
CENELEC EN 60998-2-4 |
Connecting devices for low voltage circuits for household and similar purposes Part 2-4: Particular requirements for twist-on connecting devices-(IEC 60998-2-4):2004, modified |
|
CENELEC EN 61557-6 |
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems |
|
CEN EN 736-1 |
Valves - Terminology Part 1: Definition of Types of Valves |
|
CEN EN 869 |
Safety of machinery - Safety requirements for pressure metal diecasting units |
|
CEN EN ISO 10303-210 |
Industrial Automation Systems and Integration - Product Data Representation and Exchange - Part 210: Application Protocol: Electronic Assembly, Interconnection, and Packaging Design-ISO 10303-210: 2001; ***For (SDO) Subscription Customers Only, To Obtain your Complimentary Copy Contact IHS at 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide*** |
|
CEN EN ISO 10497 |
Testing of valves - Fire type-testing requirements-ISO 10497:2004 |
|
CEN EN ISO 13916 |
Welding - Guidance on the Measurement of Preheating Temperature, Interpass Temperature and Preheat Maintenance Temperature-ISO 13916: 1996 |
|
CEN EN ISO 1580 |
Slotted Pan Head Screws- Product Grade A (ISO 1580:1994) |
|
CEN EN ISO 4016 |
Hexagon Head Bolts - Product Grade C-ISO 4016:1999; Supersedes EN 24016:1991 |
|
CEN EN ISO 7091 |
Plain Washers - Normal Series - Product Grade C-ISO 7091:2000 |
|
CEN EN ISO 7092 |
Plain Washers - Small Series - Product Grade A-ISO 7092:2000 |
|
CEN EN ISO 8502-3 |
Preparation of Steel Substrates Before Application of Paints and Related Products - Test for the Assessment of Surface Cleanliness Part 3: Assessment of Dust on Steel Surfaces Prepared for Painting (Presssure-Sensitive Tape Method)-ISO 8502-3:1992 |
|
CENELEC HD 21.3 |
Polyvinyl Chloride (PVC) Insulated Cables and Flexible Cords of Rated Voltage Uo/U up to and Including 450/750v |
|
CENELEC CLC/TS 60034-18-34 |
Rotating electrical machines Part 18-34: Functional evaluation of insulation systems Test procedures for form-wound windings Evaluation of thermomechanical endurance of insulation systems-IEC/TS 60034-18-34: 2000 |
|
CEN CR 13445-7 |
Unfires Pressure Vessels - Part 7: Guidance on the Use of the Conformity Procedures |
|
CEN EN 10217-5 |
Welded steel tubes for pressure purposes Technical delivery conditions Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperatures properties-Includes amendment A1:2005 |
|
CEN EN 12062 |
Non-destructive examination of welds General rules for metallic materials-Includes amendments A1:2002 and A2:2003 |
|
CEN EN 12417 |
Machine Tools - Safety - Machining Centres-Incorporating Amendment 1: March 2006 |
|
CEN EN 1247 |
Foundry machinery - Safety requirements for ladles, pouring equipment, centrifugal casting machines, continuous and semi continuous casting machines |
|
CEN EN 13160-2 |
Leak detection systems - Part 2: Pressure and vacuum systems |
|
CEN EN 14399-6 |
High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers-Including Corrigendum January 2006 |
|
CEN EN 14620-5 |
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and p165 °C Part 5: Testing, drying, purging and cool-down |
|
CEN EN 1626 |
Cryogenic Vessels - Valves for Cryogenic Service |
|
CEN EN 1714 |
Non-destructive testing of welds Ultrasonic testing of welded joints-Includes amendments A1:2002 and A2:2003 |
|
CEN EN 1834-3 |
Reciprocating Internal Combustion Engines - Safety Requirements for Design and Construction of Engines for Use in Potentially Explosives Atmospheres - Part 3: Group II Engines for Use in Flammable Dust Atmospheres |
|
CENELEC EN 50281-2-1 |
Electrical Apparatus for Use in the Presence of Combustible Dust - Part 2-1: Test Methods - Methods of Determining Minimum Ignition Temperatures |
|
CENELEC EN 50308 |
Wind turbines - Protective measures - Requirements for design, operation and maintenance-Incorporates Corrigendum February 2005 |
|
CEN EN 561 |
Gas Welding Equipment - Quick-Action Couplings with Shut-Off Valves for Welding, Cutting and Allied Processes |
|
CENELEC EN 60216-3 |
Electrical insulating materials - Thermal endurance properties Part 3: Instructions for calculating thermal endurance characteristics |
|
CENELEC EN 60335-2-67 |
Household and similar electrical appliances - Safety Part 2-67: Particular requirements for floor treatment and floor cleaning machines, for industrial and commercial use-Incorporates Amendment A1: 03/2006 and Corrigendum: 12/2006 |
|
CENELEC EN 60335-2-95 |
Household and similar electrical appliances - Safety Part 2-95: Particular requirements for drives for vertically moving garage doors for residential use-IEC 60335-2-95:2002, modified |
|
CENELEC EN 60335-2-97 |
Household and similar electrical appliances - Safety Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment |
|
CENELEC EN 60598-2-10 |
Luminaires Part 2-10: Particular requirements - Portable luminaires for children-Incorporates Corrigendum August 2005; IEC 60598-2-10:2003 |
|
CENELEC EN 60664-5 |
Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm |
|
CENELEC EN 60811-1-4 |
Insulating and sheathing materials of electric cables - Common test methods - Part 1-4: General application - Tests at low temperature-Includes amendment A2: 2001; IEC 60811-1-4: 1985 + Corrigendum May 1986 + A1: 1993 + A2: 2001; Supersedes HD 505.1.4 S1: 1988 |
|
CENELEC EN 60998-2-3 |
Connecting Devices for Low-Voltage Circuits for Household and Similar Purposes - Part 2-3: Particular Requirements for Connecting Devices as Separate Entities with Insulation Piercing Clamping Units |
|
CENELEC EN 61212-3-3 |
Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 3: Specifications for individual materials Sheet 3: Round laminated moulded rods-IEC 61212-3-3:2006 |
|
CENELEC EN 61326-2-4 |
Electrical equipment for measurement, control and laboratory use - EMC requirements Part 2-4: Particular requirements Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9 |
|
CENELEC EN 61326-2-5 |
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61784-1, CP 3/2 |
|
CEN EN 710 |
Safety Requirements for Foundry Moulding and Coremaking Machinery and Plant and Associated Equipment |
|
CEN EN 730-2 |
Gas welding equipment Safety devices Part 2: Not incorporating a flame (flashback) arrestor |
|
CEN EN 875 |
Destructive Tests on Welds in Metallic Materials - Impact Tests - Test Specimen Location, Notch Orientation and Examination |
|
CENELEC EN 88528-11 |
Reciprocating internal combustion engine driven alternating current generating sets Part 11: Rotary uninterruptible power systems - Performance requirements and test methods |
|
CEN EN ISO 11688-2 |
Acoustics - Recommended Practice for the Design of Low-Noise Machinery and Equipment - Part 2: Introduction to the Physics of Low-Noise Design-ISO/TR 11688-2: 1998 |
|
CEN EN ISO 1402 |
Rubber and Plastics Hoses and Hose Assemblies - Hydrostatic Testing-ISO 1402: 1994 |
|
CEN EN ISO 19879 |
Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections-ISO 19879: 2005 |
|
CEN EN ISO 6413 |
Technical Drawings - Representation of Splines and Serrations |
|
CEN EN ISO 7751 |
Rubber and Plastics Hoses and Hose Assemblies - Ratios of Proof and Burst Pressure to Design Working Pressure-ISO 7751: 1991 |
|
CEN EN ISO 8503-5 |
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blastcleaned steel substrates - Part 5: Replica tape method for the determination of the surface profile (ISO 8503-5:2003) |
|
CEN EN ISO 9606-4 |
Approval Testing of Welders - Fusion Welding - Part 4: Nickel and Nickel Alloys-ISO 6906-4:1999 |
|
CEN EN ISO 9692-2 |
Welding and Allied Processes - Joint Preparation - Part 2: Submerged Arc Welding of Steels-ISO 9692-2: 1998; Supersedes EN 29692-2: 1994 |
|
CEN EN 10217-4 |
Welded steel tubes for pressure purposes Technical delivery conditions Part 4: Electric welded non-alloy steel tubes with specified low temperature properties-includes amendment A1:2005 |
|
CEN EN 10217-6 |
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties-Includes amendment A1:2005 |
|
CEN EN 10289 |
Steel Tubes and Fittings for Onshore and Offshore Pipelines - External Liquid Applied Epoxy and Epoxy-Modified Coatings |
|
CEN EN 1197 |
Chemicals Used for Treatment of Water Intended for Human Consumption - Monozinc Phosphate Solution |
|
CEN EN 12201-3 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 3: Fittings |
|
CEN EN 12201-5 |
Plastics piping systems for water supply - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
|
CEN EN 12266-1 |
Industrial valves Testing of valves Part 1: Pressure tests, test procedures and acceptance criteria Mandatory requirements |
|
CEN EN 12972 |
Tanks for Transport of Dangerous Goods - Testing, Inspection and Marking of Metallic Tanks |
|
CEN EN 13160-5 |
Leak detection systems - Part 5: Tank gauge leak detection systems-Incorporating corrigendum February 2007 |
|
CEN EN 1320 |
Destructive Tests on Welds in Metallic Materials - Fracture Test |
|
CEN EN 13298 |
Railway applications Suspension components Helical suspension springs, steel |
|
CEN EN 13597 |
Railway applications Rubber suspension components Rubber diaphragms for pneumatic suspension springs |
|
CEN EN 13789 |
Industrial valves - Cast iron globe valves |
|
CEN EN 14620-1 |
Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0°C and p165°C Part 1: General |
|
CEN EN 15218 |
Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling - Terms, definitions, test conditions, test methods and requirements |
|
CEN EN 1713 |
Non-destructive testing of welds Ultrasonic testing Characterization of indications in welds-Includes Amendments A1:2002 and A2:2003 |
|
CEN EN 1792 |
Welding - Multilingual list of terms for welding and related processes |
|
CEN EN 286-3 |
Simple Unfired Pressure Vessels Designed to Contain Air or Nitrogen - Part 3: Steel Pressure Vessels Designed for Air Braking Equipment and Auxiliary Pneumatic Equipment for Railway Rolling Stock |
|
CENELEC EN 50086-2-4 |
Conduit Systems for Cable Management - Part 2-4: Particular Requirements for Conduit Systems Buried Underground-Includes Amendment A1: 2001; Incorporating Corrigendum February 2001 |
|
CENELEC EN 50272-2 |
Safety Requirements for Secondary Batteries and Battery Installations Part 2: Stationary Batteries |
|
CENELEC EN 60068-3-7 |
Environmental Testing - Part 3-7: Supporting Documentation and Guidance - Measurements in Temperature Chambers for Tests A and B (With Load)-IEC 60068-3-7:2001 |
|
CENELEC EN 60255-21-3 |
Electrical Relays Part 21: Vibration, Shock, Bump and Seismic Tests on Measuring Relays and Protection Equipment Section 3: Seismic Tests (IEC 255-21-3 : 1993) |
|
CENELEC EN 60255-3 |
Electrical Relays Part 3: Single Input Energizing Quantity Measuring Relays with Dependent or Independent Time-IEC 60255-3:1989, Modified |
|
CENELEC EN 60332-2-2 |
Tests on electric and optical fibre cables under fire conditions Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame-IEC 60332-2-2:2004; Supersedes EN 50265-2-2:1998 |