|
CEN EN 14111 |
Fat and oil derivatives - Fatty Acid Methyl Esters (FAME) - Determination of iodine value |
|
CEN EN 14121 |
Aluminium and aluminium alloys - Aluminium sheet, strip and plate for electrotechnical applications |
|
CEN EN 14538 |
Fat and oil derivatives - Fatty acid methyl ester (FAME) - Determination of Ca, K, Mg and Na content by optical emission spectral analysis with inductively coupled plasma (ICP OES) |
|
CEN EN 14932 |
Plastics - Stretch thermoplastic films for wrapping bales - Requirements and test methods |
|
CEN EN 309 |
Particleboards - Definition and classification |
|
CEN EN 31092 |
Textiles - Determination of Physiological Properties - Measurement of Thermal and Water- Vapour Resistance Under Steady-State Conditions (Sweating Guarded- Hotplate Test) (ISO 11092 : 1993) |
|
CEN EN 313-2 |
Plywood - Classification and Terminology - Part 2: Terminology |
|
CEN EN 326-1 |
Wood-Based Panels - Sampling, Cutting and Inspection - Part 1: Sampling and Cutting of Test Pieces and Expression of Test Results |
|
CEN EN 422 |
Rubber and Plastics Machines - Safety - Blow Moulding Machines Intended for the Production of Hollow Articles - Requirements for the Design and Construction |
|
CEN EN 477 |
Unplasticized Polyvinylchloride (PVC-U) Profiles for the Fabrication of Windows and Doors - Determination of the Resistance to Impact of Main Profiles by Falling Mass |
|
CEN EN 610 |
Tin and Tin Alloys - Ingot Tin |
|
CEN EN 635-5 |
Plywood - Classification by Surface Appearance - Part 5: Methods for Measuring and Expressing Characteristics and Defects |
|
CEN EN 646 |
Paper and Board Intended to Come into Contact with Foodstuffs - Determination of Colour Fastness of Dyed Paper and Board |
|
CEN EN 827 |
Adhesives - Determination of Conventional Solids Content and Constant Mass Solids Content |
|
CEN EN 993-14 |
Methods of Test for Dense Shaped Refractory Products - Part 14: Determination of Thermal Conductivity by the Hot-Wire (Cross-Array) Method |
|
CEN EN ISO 10417 |
Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress-ISO 10417:2004 |
|
CEN EN ISO 10964 |
Adhesives - Determination of Torque Strength of Anaerobic Adhesives on Threaded Fasteners-ISO 10964: 1993 |
|
CEN EN ISO 1133 |
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics-ISO 1133: 2005 |
|
CEN EN ISO 13705 |
Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service-ISO 13705: 2006 |
|
CEN EN ISO 14126 |
Fibre-reinforced plastic composites Determination of compressive properties in the in-plane direction-ISO 14126:1999; Incorporating corrigendum July 2002 |
|
CEN EN ISO 15541 |
Ships and Marine Technology - Fire Resistance of Hose Assemblies - Requirements for the Test Bench-ISO 15541:1999 |
|
CEN EN ISO 18064 |
Thermoplastic elastomers - Nomenclature and abbreviated terms-(ISO 18064):2003 |
|
CEN EN ISO 22088-1 |
Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 1: General guidance-ISO 22088-1:2006 |
|
CEN EN ISO 22088-4 |
Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 4: Ball or pin impression method-ISO 22088-4:2006;:1997 |
|
CEN EN ISO 2555 |
Plastics - Resins in the Liquid State or as Emulsions or Dispersions - Determination of Apparent Viscosity by the Brookfield Test Method-ISO 2555: 1989 |
|
CEN EN ISO 294-1 |
Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 1: General Principles, and Moulding of Multipurpose and Bar Test Specimens-Includes Amendment A1: 2002; ISO 294-1:1996 + A1:2001 |
|
CEN EN ISO 295 |
Plastics - Compression moulding of test specimens of thermosetting materials-ISO 295:2004 |
|
CEN EN ISO 3451-5 |
Plastics - Determination of Ash - Part 5: Poly(Vinyl Chloride)-ISO 3451-5: 2002 |
|
CEN EN ISO 377 |
Steel and Steel Products - Location and Preparation of Samples and Test Pieces for Mechanical Testing-ISO 377: 1997 |
|
CEN EN ISO 3977-5 |
Gas turbines Procurement Part 5: Applications for petroleum and natural gas industries-ISO 3977-5:2001 |
|
CEN EN ISO 7391-1 |
Plastics - Polycarbonate (PC) Moulding and Extursion Materials - Part 1: Designation System and Basis for Specifications-ISO 7391-1:2006 |
|
CEN ISO/DIS 12100-1 |
Safety of Machinery - Basic Concepts and General Principles for Design - Part 1: Basic Terminology and Methodology |
|
CEN EN 10056-1 |
Structural Steel Equal and Unequal Leg Angles - Part 1: Dimensions |
|
CEN EN 10085 |
Nitriding Steels - Technical Delivery Conditions |
|
CEN EN 10106 |
Cold Rolled Non-Oriented Electrical Steel Sheet and Strip Delivered in the Fully Processed State |
|
CEN EN 10132-2 |
Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 2: Case Hardening Steels |
|
CEN EN 10222-5:1999/AC |
Steel Forgings for Pressure Purposes - Part 5: Martensitic, Austenitic and Austenitic-Ferritic Stainless Steels-Ratified European Text |
|
CEN EN 10308 |
Non-Destructive Testing - Ultrasonic Testing of Steel Bars |
|
CEN EN 1034-6 |
Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 6: Calender |
|
CEN EN 12081 |
Railway Applications - Axleboxes - Lubricating Greases |
|
CEN EN 1230-1 |
Paper and Board Intended for Contact with Foodstuffs - Sensory Analysis - Part 1: Odour |
|
CEN EN 12369-1 |
Wood Based Panels - Characteristic Values for Structural Design - Part 1: OSB, Particleboards and Fibreboards |
|
CEN EN 13509 |
Cathodic protection measurement techniques |
|
CEN EN 13601 |
Copper and Copper Alloys - Copper Rod, Bar and Wire for General Electrical Purposes |
|
CEN EN 13605 |
Copper and copper alloys - Copper profiles and profiled wire for electrical purposes |
|
CEN EN 14110 |
Fat and oil derivatives - Fatty Acid Methyl Esters (FAME) - Determination of methanol content |
|
CEN EN 14163 |
Petroleum and Natural Gas Industries - Pipeline Transportation Systems - Welding of Pipelines-ISO 13847: 2000 Modified |
|
CEN EN 1870-1 |
Safety of woodworking machines - Circular sawing machines - Part 1: Circular saw benches (with and without sliding table), dimension saws and building site saws |
|
CEN EN 201 |
Rubber and Plastics Machines - Injection Moulding Machines - Safety Requirements-Includes amendments A1:2000 and A2:2005 |
|
CEN EN 312 |
Particleboards - Specifications-Supersedes EN 312-1 thru -4: 1996; EN 321-5: 1997; EN 312-6: 1996; En 312-7: 1997 |
|
CEN EN 546-2 |
Aluminium and Aluminium Alloys - Foil - Part 2: Mechanical Properties |
|
CEN EN 848-1 |
Safety of Woodworking Machines - One Side Moulding Machines with Rotating Tool - Part 1: Single Spindle Vertical Moulding Machines |
|
CEN EN 993-15 |
Methods of test for dense shaped refractory products - Determination of thermal conductivity by the hot-wire (parallel) method |
|
CEN EN ISO 10156-2 |
Gas cylinders Gases and gas mixtures Part 2: Determination of oxidizing ability of toxic and corrosive gases and gas mixtures-ISO 10156-2:2005 |
|
CEN EN ISO 12952-2 |
Textiles - Burning Behaviour of Bedding Items - Part 2: Specific Test Methods for the Ignitability by a Smouldering Cigarette-ISO 12952-2:1998 |
|
CEN EN ISO 13710 |
Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps-ISO 13710:2004 |
|
CEN EN ISO 14556 |
Steel - Charpy V-Notch Pendulum Impact Test - Instrumented Test Method-Includes amendment A1:2006; ISO 14556:2000 |
|
CEN EN ISO 15138 |
Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning |
|
CEN EN ISO 1622-2 |
Plastics - Polystyrene (PS) Moulding and Extrusion Materials Part 2: Preparation of Test Specimens and Determination of Properties-ISO 1622-2:1995 |
|
CEN EN ISO 2566-2 |
Steel - Conversion of Elongation Values - Part 2: Austenitic Steels-ISO 2566-2: 1984 |
|
CEN EN ISO 3953 |
Metallic Powders - Determination of Tap Density (ISO 3953: 1993) |
|
CEN EN ISO 4613-1 |
Plastics - Ethylene/Vinyl Acetate (E/VAC) Moulding and Extrusion Materials - Part 1: Designation and Specification-ISO 4613-1:1993 |
|
CEN EN ISO 6326-3 |
Natural Gas - Determination of Sulfur Compounds - Part 3: Determination of Hydrogen Sulfide, Mercaptan Sulfur and Carbonyl Sulfide Sulfur by Potentiometry-ISO 6326-3: 1989 |
|
CEN EN ISO 6507-3 |
Metallic materials - Vickers hardness test - Part 3: Calibration of reference blocks-ISO 6507-3: 2005 |
|
CEN ENV 14226 |
Advanced Technical Ceramics - Test Methods for Ceramic Powders - Determination of Calcium, Magnesium, Iron and Aluminium in Silicon Nitride by Using Flame Atomic Absorption Spectroscopy (FAAS) or Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES) |
|
CEN EN 10061 |
Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
|
CEN EN 10132-1 |
Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 1: General |
|
CEN EN 10132-3 |
Cold Rolled Narrow Steel Strip for Heat Treatment - Technical Delivery Conditions - Part 3: Steels for Quenching and Tempering |
|
CEN EN 10216-3 |
Seamless Steel Tubes for Pressure Purposes - Technical Delivery Conditions - Part 3: Alloy Fine Grain Steel Tubes-Includes Amendment A1:2004 |
|
CEN EN 10257-2 |
Zinc or Zinc Alloy Coated Non-Alloy Steel Wire for Armouring Either Power Cables or Telecommunication Cables - Part 2: Submarine Cables |
|
CEN EN 10263-5 |
Steel Rod, Bars and Steel Wire for Cold Heading and Cold Extrusion - Part 5: Technical Delivery Conditions for Stainless Steels |
|
CEN EN 1034-4 |
Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 4: Pulpers and their loading facilities |
|
CEN EN 1071-1 |
Advanced technical ceramics Methods of test for ceramic coatings Part 1: Determination of coating thickness by contact probe filometer-Supersedes ENV 1071-1:1993 |
|
CEN EN 12012-1 |
Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators |
|
CEN EN 12167 |
Copper and Copper Alloys - Profiles and Rectangular Bar for General Purposes |
|
CEN EN 12258-1 |
Aluminium and Aluminium Alloys - Terms and Definitions - Part 1: General Terms-Supersedes EN 23134-1:1991; EN 23134-2:1991; EN 23134-3:1991; EN 23134-4:1991 |
|
CEN EN 12495 |
Cathodic Protection for Fixed Steel Offshore Structures |
|
CEN EN 12505 |
Food Processing Machinery - Centrifugal Machines for Processing Edible Oils and Fats - Safety and Hygiene Requirements |
|
CEN EN 12547 |
Centrifuges - Common Safety Requirements |
|
CEN EN 13673-1 |
Determination of the maximum explosion pressure and the maximum rate of pressure rise of gases and vapours - Part 1: Determination of the maximum explosion pressure |
|
CEN EN 14103 |
Fat and oil derivatives - Fatty Acid Methyl Esters (FAME) - Determination of ester and linolenic acid methyl ester contents |
|
CEN EN 14175-1 |
Fume cupboards Part 1: Vocabulary |
|
CEN EN 14331 |
Liquid petroleum products - Separation and characterisation of fatty acid methyl esters (FAME) from middle distillates - Liquid chromatography (LC)/gas chromatography (GC) method |
|
CEN EN 1464 |
Adhesives - Determination of Peel Resistance of High-Strength Adhesive Bonds - Floating Roller Method (ISO 4578:1990 Modified) |
|
CEN EN 1677-2 |
Components for Slings - Safety - Part 2: Forged Steel Lifting Hooks with Latch, Grade 8 |
|
CEN EN 515 |
Aluminium and Aluminium Alloys - Wrought Products - Temper Designations |
|
CEN EN 572-1 |
Glass in building - Basic soda lime silicate glass products - Part 1: Definitions and general physical and mechanical properties-Incorporating Corrigendum September 2004 |
|
CEN EN 755-7 |
Aluminium and Aluminium Alloys - Extruded Rod/Bar, Tube and Profiles - Part 7: Seamless Tubes, Tolerances on Dimensions and Form |
|
CEN EN 847-1 |
Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades-Incorporates Amendment A1: August 2007 |
|
CEN EN 993-8 |
Methods of Test for Dense Shaped Refractory Products - Part 8: Determination of Refractoriness-Under-Load |
|
CEN EN ISO 11961 |
Petroleum and Natural Gas Industries - Steel Pipes for Use as Drill Pipe - Specification-ISO 11961 : 1996 |
|
CEN EN ISO 14691 |
Petroleum and Natural Gas Industries - Flexible Couplings for Mechanical Power Transmission - General Purpose Applications-ISO 14691: 1999 |
|
CEN EN ISO 1874-1 |
Plastics - Polyamide (PA) Moulding and Extrusiuon Materials - Part 1: Designation-ISO 1874-1:1992 |
|
CEN EN ISO 21049 |
Pumps - Shaft sealing systems for centrifugal and rotary pumps-Incorporating corrigendum February 2005; ISO 21049:2004 |
|
CEN EN ISO 2566-1 |
Steel - Conversion of Elongation Values - Part 1: Carbon and Low Alloy Steels-ISO 2566-1:1984 |
|
CEN EN ISO 3696 |
Water for Analytical Laboratory Use- Specification and Test Methods (ISO 3696 : 1987) |
|
CEN EN ISO 4892-3 |
Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps-ISO 4892-3:2006 |
|
CEN EN ISO 6506-3 |
Metallic Materials - Brinell Hardness Test - Part 3: Calibration of Reference Blocks-ISO 6506-3:2005 |
|
CEN EN ISO 7153-1 |
Surgical Instruments - Metallic Materials - Part 1: Stainless Steel-ISO 7153-1:1991; Including Amendment 1:1999 |
|
CEN EN ISO 899-2 |
Plastics - Determination of Creep Behaviour - Part 2: Flexural Creep by Three-Point Loading-ISO 899-2: 2003 |
|
CEN CEN/TS 15280 |
Evaluation of a.c. corrosion likelihood of buried pipelines Application to cathodically protected pipelines |
|
CEN EN 10055 |
Hot Rolled Steel Equal Flange Tees with Radiused Root and Toes - Dimensions and Tolerances on Shape and Dimensions |
|
CEN EN 10139 |
Cold Rolled Uncoated Mild Steel Narrow Strip for Cold Forming - Technical Delivery Conditions |
|
CEN EN 10207 |
Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars |
|
CEN EN 10216-4 |
Seamless Steel Tubes for Pressure Purposes - Technical Delivery Conditions - Part 4: Non-alloy and alloy steel tubes with specified low temperature properties-Includes Amendment A1:2004 |
|
CEN EN 10228-4 |
Non-Destructive Testing of Steel Forgings - Part 4: Ultrasonic Testing of Austenitic and Austenitic-Ferritic Stainless Steel Forgings |
|
CEN EN 10279 |
Hot Rolled Steel Channels - Tolerances on Shape, Dimension and Mass |
|
CEN EN 10302 |
Creep Resisting Steels, Nickel and Cobalt Alloys |
|
CEN EN 10305-4 |
Steel tubes for precision applications - Technical delivery conditions - Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems |
|
CEN EN 10333 |
Steel for packaging - Flat steel products intended for use in contact with foodstuffs, products and beverages for human and animal consumption - Tin coated steel (tinplate) |
|
CEN EN 1034-13 |
Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units |
|
CEN EN 1034-7 |
Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 7: Chests |
|
CEN EN 12513 |
Founding - Abrasion Resistant Cast Irons |
|
CEN EN 12588 |
Lead and Lead Alloys - Rolled Lead Sheet for Building Purposes |
|
CEN EN 12844 |
Zinc and Zinc Alloys - Castings - Specifications-Ratified European Text |
|
CEN EN 13177 |
Chemicals used for treatment of water intended for human consumption - Methanol |
|
CEN EN 1403 |
Corrosion Protection of Metals - Electrodeposited Coatings - Method of Specifying General Requirements |
|
CEN EN 14078 |
Liquid petroleum products Determination of fatty acid methyl esters (FAME) in middle distillates Infrared spectroscopy method |
|
CEN EN 14814 |
Adhesives for thermoplastic piping systems for fluids under pressure - Specifications |
|
CEN EN 15111 |
Foodstuffs - Determination of trace elements - Determination of iodine by ICP-MS (inductively coupled plasma mass spectrometry) |
|
CEN EN 15112 |
External cathodic protection of well casings |
|
CEN EN 1594 |
Gas Supply Systems - Pipelines for Maximum Operating Pressure Over 16 Bar - Functional Requirements |
|
CEN EN 589 |
Automotive fuels - LPG - Requirements and test methods-Incorporating Corrigendum December 2005 |
|
CEN EN 622-2 |
Fibreboards - Specifications - Part 2: Requirements for hardboards-Incorporating Corrigendum: 12/2005 |
|
CEN EN 643 |
Paper and Board - European List of Standard Grades of Recovered Paper and Board |
|
CEN EN ISO 10350-2 |
Plastics - Acquisition and Presentation of Comparable Single-Point DataPart 2: Long-Fibre-Reinforced Plastic-ISO 10350-2:2001 |
|
CEN EN ISO 10432 |
Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment-ISO 10432:2004 |
|
CEN EN ISO 10437 |
Petroleum, petrochemical and natural gas industries Steam turbines Special-purpose applications-ISO 10437:2003 |
|
CEN EN ISO 12922 |
Lubricants, Industrial Oils and Related Products (Class L) - Family H (Hydraulic Systems) - Specifications for Categories HFAE, HFAS, HFB, HFC, HFDR and HFDU |
|
CEN EN ISO 12952-3 |
Textiles - Burning Behaviour of Bedding Items - Part 3: General Test Methods for the Ignitability by a Small Open Flame-ISO 12952-3:1998 |
|
CEN EN ISO 527-4 |
Plastics - Determination of Tensile Properties - Part 4: Test Conditions for Isotropic and Orthotropic Fibre-Reinforced Plastic Composites-ISO 527-4: 1997 |
|
CEN EN ISO 5659-2 |
Plastics - Smoke Generation - Part 2: Determination of Optical Density by a Single-Chamber Test |
|
CEN EN ISO 642 |
Steel - Hardenability Test by End Quenching (Jominy Test)-ISO 642: 1999 |
|
CEN EN ISO 6508-3 |
Metallic materials - Rockwell hardness test - Part 3: Calibration of reference blocks (scales A, B, C, D, E, F, G, H, K, N, T)-ISO 6508-3:2005 |
|
CEN EN ISO 6721-2 |
Plastics - Determination of Dynamic Mechanical Properties - Part 2: Torsion-Pendulum Method (ISO 6721-2 : 1994, Including Technical Corrigendum 1: 1995) |
|
CEN CEN ISO/TR 20572 |
Footwear - Performance requirements for components for footwear - Accessories |
|
CEN CEN ISO/TR 20883 |
Footwear - Performance requirements for components for footwear - Shanks |
|
CEN CEN/TR 15591 |
Solid recovered fuels - Determination of the biomass content based on the 14C method |
|
CEN EN 10017 |
Steel rod for drawing and/or cold rolling - Dimensions and tolerances |
|
CEN EN 10028-3 |
Flat products made of steels for pressure purposes Part 3: Weldable fine grain steels, normalized |
|
CEN EN 10028-6 |
Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered |
|
CEN EN 10089 |
Hot rolled steels for quenched and tempered springs Technical delivery conditions |
|
CEN EN 10143 |
Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape |
|
CEN EN 10222-3 |
Steel Forgings for Pressure Purposes - Part 3: Nickel Steels with Specified Low Temperature Properties-Ratified European Text |
|
CEN EN 10223-1 |
Steel Wire and Wire Products for Fences - Part 1: Zinc and Zinc Alloy Coated Steel Barbed Wire |
|
CEN EN 10295 |
Heat resistant steel castings |
|
CEN EN 10336 |
Continuously hot-dip coated and electrolytically coated strip and sheet of multiphase steels for cold forming - Technical delivery conditions |
|
CEN EN 12020-2 |
Aluminium and Aluminium Alloys - Extruded Precision Profiles in Alloys EN AW-6060 and EN AW-6063 - Part 2: Tolerances on Dimensions and Form |
|
CEN EN 12246 |
Quality Classification of Timber Used in Pallets and Packaging |
|
CEN EN 12268 |
Food processing machinery - Band saw machines - Safety and hygiene requirements |
|
CEN EN 12373-4 |
Aluminium and Aluminium Alloys - Anodizing - Part 4: Estimation of Loss of Absorptive Power of Anodic Oxidation Coatings After Sealing by Dye Spot Test with Prior Acid Treatment |
|
CEN EN 12508 |
Corrosion Protection of Metals and Alloys - Surface Treatment, Metallic and Other Inorganic Coatings - Vocabulary |
|
CEN EN 12952-2 |
Water-Tube Boilers and Auxiliary Installations - Part 2: Materials for Pressure Parts of Boilers and Accessories |
|
CEN EN 13288 |
Food processing machinery Bowl lifting and tilting machines Safety and hygiene requirements |
|
CEN EN 13297 |
Textile Floor Coverings - Classification of Needled Pile Floor Coverings |
|
CEN EN 13378 |
Pasta Proccessing Plants - Pasta Presses - Safety and Hygiene Requirements |
|
CEN EN 13390 |
Food Processing Machinery - Pie and Tart Machines - Safety and Hygiene Requirements |
|
CEN EN 13602 |
Copper and Copper Alloys - Drawn, Round Copper Wire for the Manufacture of Electrical Conductors |
|
CEN EN 13603 |
Copper and Copper Alloys - Test Methods for Assessing Protective Tin Coatings on Drawn Round Copper Wire for Electrical Purposes |
|
CEN EN 13706-2 |
Reinforced plastics composites Specifications for pultruded profiles Part 2: Method of test and general requirements |
|
CEN EN 13756 |
Wood flooring Terminology |
|
CEN EN 13857-1 |
Explosives for civil uses - Part 1: Terminology |
|
CEN EN 14057 |
Lead and lead alloys Scraps Terms and definitions |
|
CEN EN 14080 |
Timber structures - Glued laminated timber - Requirements |
|
CEN EN 14108 |
Fat and oil derivatives - Fatty Acid Methyl Esters (FAME) - Determination of sodium content by atomic absorption spectrometry |
|
CEN EN 14358 |
Timber structures - Calculation of characteristic 5-percentile values and acceptance criteria for a sample |
|
CEN EN 14987 |
Plastics - Evaluation of disposability in waste water treatment plants - Test scheme for final acceptance and specifications |
|
CEN EN 15063-1 |
Copper and copper alloys - Determination of main constituents and impurities by wavelength dispersive X-ray fluorescence spectrometry (XRF) - Part 1: Guidelines to the routine method |
|
CEN EN 15284 |
Materials and articles in contact with food stuffs - Test method for the resistance to microwave heating of ceramic, glass, glassceramic or plastics cookware |
|
CEN EN 15529 |
Derivatives from coal pyrolysis - Terminology |
|
CEN EN 1559-5 |
Founding - Technical Conditions of Delivery - Part 5: Additional Requirements for Magnesium Alloy Castings |
|
CEN EN 1655 |
Copper and Copper Alloys - Declarations of Conformity |
|
CEN EN 1860-1 |
Appliances, solid fuels and firelighters for barbecueing - Part 1: Barbecues burning solid fuels - Requirements and test methods-Includes Amendment 1: February 2006 |
|
CEN EN 1977 |
Copper and Copper Alloys - Copper Drawing Stock (Wire Rod) |
|
CEN EN 28510-1 |
Adhesives - Peel Test for a Flexible-Bonded-to- Rigid Test Specimen Assembly - Part 1: 90 Degree Peel (ISO 8510-1 : 1990) |
|
CEN EN 28510-2 |
Adhesives - Peel Test for a Flexible-Bonded-to- Rigid Test Specimen Assembly - Part 2: 180 Degree Peel (ISO 8510-2 : 1990) |
|
CEN EN 326-3 |
Wood-Based Panels - Sampling, Cutting and Inspection - Part 3: Inspection of an Isolated lot of Panels |
|
CEN EN 335-1 |
Durability of wood and wood- based products - Definition of use classes - Part 1: General |
|
CEN EN 4004 |
Aerospace series - Aluminium alloy AL-P3103-H16 - Sheet and strip 0,4 mm < or = to a < or = to 6 mm |
|
CEN EN 4005 |
Aerospace series - Aluminium alloy AL-P5052-O - Sheet and strip 0,3 mm less than equal to a less than equal to 6 mm |
|
CEN EN 523 |
Steel Strip Sheaths for Prestressing Tendons - Terminology, Requirements Quality Control |
|
CEN EN 546-1 |
Aluminium and Aluminium Alloys - Foil - Part 1: Technical Conditions for Inspection and Delivery |
|
CENELEC EN 60746-3 |
Expression of performance of electrochemical analyzers Part 3: Electrolytic conductivity-IEC 60746-3: 2002 |
|
CEN EN 622-1 |
Fibreboards - Specifications - Part 1: General Requirements |
|
CEN EN 755-5 |
Aluminium and Aluminium Alloys - Extruded Rod/ Bar, Tube and Profiles - Part 5: Rectangular Bars, Tolerances on Dimensions and Form |
|
CEN EN 755-6 |
Aluminium and Aluminium Alloys - Extruded Rod/ Bar, Tube and Profiles - Part 6: Hexagonal Bars, Tolerances on Dimensions and Form |
|
CEN EN 844-7 |
Round and Sawn Timber - Terminology - Part 7: Terms Relating to Anatomical Structure of Timber |
|
CEN EN 844-8 |
Round and Sawn Timber - Terminology - Part 8: Terms Relating to Features of Round Timber |
|
CEN EN 848-3 |
Safety of woodworking machines - One side moulding machines with rotating tools - Part 3: Numerically controlled (NC) boring and routing machines |
|
CEN EN 940 |
Safety of Woodworking Machines - Combined Woodworking Machines |
|
CEN EN 993-17 |
Methods of Test for Dense Shaped Refractory Products - Part 17: Determination of Bulk Density of Granular Materials by the Mercury Method with Vacuum |
|
CEN EN 993-18 |
Methods of test for dense shaped refractory products - Part 18: Determination of bulk density of granular materials by the water method with vacuum |
|
CEN EN ISO 10438-2 |
Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems |
|
CEN EN ISO 105-J05 |
Textiles - Tests for colour fastness - Part J05: Method for the instrumental assessment of the colour inconstancy of a specimen with change in illuminant (CMCCONO2) |
|
CEN EN ISO 10724-1 |
Plastics - Injection Moulding of Test Specimens of Thermosetting Powder Moulding Compounds (PMCs) - Part 1: General Principles and Moulding of Multipurpose Test Specimens-ISO 10724-1:1998 |
|
CEN EN ISO 11111-1 |
Textile machinery - Safety requirements - Part 1: Common requirements-ISO 11111-1:2005; Supersedes EN ISO 11111:1995 |
|
CEN EN ISO 11409 |
Plastics - Phenolic Resins - Determination of Heats and Temperatures of Reaction by Differential Scanning Calorimetry-ISO 11409:1993 |
|
CEN EN ISO 1211 |
Milk - Determination of Fat Content - Gravimetric Method (Reference Method)-ISO 1211:1999 |
|
CEN EN ISO 12680-1 |
Methods of test for refractory products - Part 1: Determination of dynamic Young's modulus (MOE) by impulse excitation of vibration |
|
CEN EN ISO 13691 |
Petroleum and natural gas industries - High-speed special-purpose gear units-ISO 13691:2001 |
|
CEN EN ISO 14284 |
Steel and iron Sampling and preparation of samples for the determination of chemical composition-ISO 14284: 1996 |
|
CEN EN ISO 15791-1 |
Plastics Development and use of intermediate-scale fire tests for plastics products Part 1: General guidance-ISO 15791-1:2002 |
|
CEN EN ISO 17707 |
Footwear Test methods for outsoles Flex resistance-ISO 17707:2005 |
|
CEN EN ISO 22088-2 |
Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 2: Constant tensile load method-ISO 22088-2:2006;:1997 |
|
CEN EN ISO 3037 |
Corrugated fibreboard - Determination of edgewise crush resistance (unwaxed edge method) |
|
CEN EN ISO 3252 |
Powder Metallurgy - Vocabulary-ISO 3252:1999 |
|
CEN EN ISO 3785 |
Metallic materials - Designation of test specimen axes in relation to product texture-ISO 3785:2006 |
|
CEN EN ISO 6974-1 |
Natural Gas - Determiantion of Composition with Defined Uncertainty by Gas Chromatography - Part 1: Guidelines for Tailored Analysis-ISO 6974-1:2000 |
|
CEN EN ISO 7278-2 |
Liquid Hydrocarbons - Dynamic Measurement - Proving Systems for Volumetric Meters - Part 2: Pipe Provers (ISO 7278-2 : 1988) |
|
CEN EN ISO 7438 |
Metallic materials Bend test |
|
CEN EN ISO 877 |
Plastics - Methods of Exposure to Direct Weathering, to Weathering Using Glass-Filtered Daylight, and to Intensified Weathering by Daylight Using Fresnel Mirrors-ISO 877:1994 |
|
CEN EN ISO 8985 |
Plastics - Ethylene/Vinyl Acetate Copolymer (EVAC) Thermoplastics - Determination of Vinyl Acetate Content-ISO 8985:1998 |
|
CEN EN ISO 9396 |
Plastics - Phenolic Resins - Determination of the Gel Time at a Given Temperature Using Automatic Apparatus-ISO 9396: 1997 |
|
CEN ENV 14232 |
Advanced technical ceramics Terms, definitions and abbreviations |
|
CEN CEN ISO/TR 20880 |
Footwear - Performance requirements for components for footwear - Outsoles |
|
CEN CEN ISO/TR 20882 |
Footwear - Performance requirements for components for footwear - Lining and insocks |
|
CEN CEN/TS 1071-10 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 10: Determination of coating thickness by cross sectioning |
|
CEN CEN/TS 1071-11 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 11: Determination of internal stress by the Stoney formula |
|
CEN CR 10313 |
Classification of Grades of Steel - Examples of Classification Related to European Standards |
|
CEN EN 1001-1 |
Durability of wood and wood-based products - Terminology - Part 1: List of equivalent terms-Supersedes HD 1001:1984 |
|
CEN EN 1001-2 |
Durability of wood and wood based products - Terminology - Part 2: Vocabulary |
|
CEN EN 10213-3 |
Technical Delivery Conditions for Steel Castings for Pressure Purposes - Part 3: Steel Grades for Use at Low Temperatures |
|
CEN EN 10246-2 |
Non-Destructive Testing of Steel Tubes - Part 2: Automatic Eddy Current Testing of Seamless and Welded (Except Submerged Arc-Welded) Austenitic and Austenitic-Ferritic Steel Tubes for Verififcation of Hydraulic Leak-Tightness |
|
CEN EN 10264-3 |
Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications |
|
CEN EN 10273 |
Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
|
CEN EN 10274 |
Metallic Materials - Drop Weight Tear Test |
|
CEN EN 10292 |
Continuously hot-dip coated strip and sheet of steels with high yield strength for cold forming - Technical delivery conditions |
|
CEN EN 10319-2 |
Metallic materials - Tensile stress relaxation testing - Part 2: Procedure for bolted joint models |
|
CEN EN 10342 |
Magnetic materials - Classification of surface insulations of electrical steel sheet, strip and laminations |
|
CEN EN 1051-1 |
Glass in building - Glass blocks and glass pavers - Part 1: Definitions and description |
|
CEN EN 1096-1 |
Glass in Building - Coated Glass - Part 1: Definitions and Classification-Ratified European Text |
|
CEN EN 12042 |
Food processing machinery - Automatic dividers - Safety and hygiene requirements |
|
CEN EN 12115 |
Rubber and Thermoplastics Hoses and Hose Assemblies for Liquid or Gaseous Chemicals - Specification |
|
CEN EN 1218-4 |
Safety of woodworking machines - Tenoning machines - Part 4: Edge banding machines fed by chain(s)-includes amendment A1:2005; Incorporating corrigendum December 2006 |
|
CEN EN 12258-2 |
Aluminium and aluminium alloys - Terms and definitions - Part 2: Chemical analysis |
|
CEN EN 12267 |
Food processing machinery - Circular saw machines - Safety and hygiene requirements |
|
CEN EN 12280-2 |
Rubber- or Plastic-Coated Fabrics - Accelerated Ageing Tests - Part 2: Physical Ageing: Effect of Light or Weathering |
|
CEN EN 12373-2 |
Aluminium and Aluminium Alloys - Anodizing - Part 2: Determination of Mass Per Unit Area (Surface Density) of Anodic Oxidation Coatings - Gravimetric Method-Ratified European Text |
|
CEN EN 12385-1 |
Steel wire ropes Safety Part 1: General requirements |
|
CEN EN 12420 |
Copper and Copper Alloys - Forgings |
|
CEN EN 12567 |
Industrial Valves - Isolating Valves for LNG - Specification for Suitability and Appropriate Verification Tests |
|
CEN EN 12698-2 |
Chemical analysis of nitride bonded silicon carbide refractories - Part 2: XRD methods |
|
CEN EN 12701 |
Structural Adhesives - Storage - Determination of Words and Phrases Relating to the Product Life of Structural Adhesives and Related Materials |
|
CEN EN 12732 |
Gas Supply Systems - Welding Steel Pipework - Functional Requirements |
|
CEN EN 12854 |
Food processing machinery - Beam mixers - Safety and hygiene requirements |
|
CEN EN 13195-1 |
Aluminium and Aluminium Alloys - Wrought and Cast Products for Marine Applications (Shipbuilding, Marine and Offshore) Part 1: Specifications |
|
CEN EN 13289 |
Pasta Processing Plants - Dryers and Coolers - Safety and Hygiene Requirements |
|
CEN EN 13418 |
Rubber and plastics machines - Winding machines for film or sheet - Safety requirements |
|
CEN EN 13556 |
Round and sawn timber - Nomenclature of timbers used in Europe |
|
CEN EN 13600 |
Copper and Copper Alloys - Seamless Copper Tubes for Electrical Purposes |
|
CEN EN 13636 |
Cathodic protection of buried metallic tanks and related piping |
|
CEN EN 13676 |
Polymer Coated Paper and Board Intended for Food Contact - Detection of Pinholes |
|
CEN EN 13706-3 |
Reinforced plastics composites Specifications for pultruded profiles Part 3: Specific requirements |
|
CEN EN 13856 |
Minimum requirements for the content of the user manual for automotive LPG systems |
|
CEN EN 13870 |
Food processing machinery - Chop cutting machines - Safety and hygiene requirements |
|
CEN EN 13885 |
Food processing machinery - Clipping machines - Safety and hygiene requirements |
|
CEN EN 13886 |
Food processing machinery - Cooking kettles equipped with powered stirrer and/or mixer - Safety and hygiene requirements |
|
CEN EN 13942 |
Petroleum and natural gas industries Pipeline transportation Pipeline valves |
|
CEN EN 14035-1 |
Fireworks Part 1: Terminology-Incorporating Corrigendum: January 2005 |
|
CEN EN 14179-2 |
Glass in building Heat soaked thermally toughened soda lime silicate safety glass Part 2: Evaluation of conformity/Product standard |
|
CEN EN 15063-2 |
Copper and copper alloys - Determination of main constituents and impurities by wavelength dispersive X-ray fluorescence spectrometry (XRF) - Part 2: Routine method |
|
CEN EN 15156 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Determination of fatigue properties at constant amplitude |
|
CEN EN 15336 |
Adhesives - Determination of the time to rupture of bonded joints under static load |
|
CEN EN 1715-4 |
Aluminium and Aluminium Alloys - Drawing Stock - Part 4: Specific Requirements for Welding Applications |
|
CEN EN 1860-2 |
Appliances, solid fuels and firelighters for barbecueing Part 2: Barbecue charcoal and barbecue charcoal briquettes - Requirements and test methods |
|
CEN EN 1870-17 |
Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws) |
|
CEN EN 1900 |
Materials and Articles in Contact with Foodstuffs - Non-Metallic Tableware - Terminology |
|
CEN EN 1963 |
Textile Floor Coverings - Tests Using the Lisson Tretrad Machine |
|
CEN EN 1967 |
Structural adhesives Evaluation of the effectiveness of surface treatment techniques for aluminium using a wet peel test in association with the floating roller method-Supersedes ENV 1967: 1995; Incorporationg Corrigendum March 2005 |
|
CEN EN 541 |
Aluminium and aluminium alloys - Rolled products for cans, closures and lids - Specifications |
|
CEN EN 586-2 |
Aluminium and Aluminium Alloys - Forgings - Part 2: Mechanical Properties and Additional Property Requirements |
|
CENELEC EN 60335-2-28 |
Household and similar electrical appliances Safety Part 2-28: Particular requirements for sewing machines-IEC 60335-2-28:2002, modified |
|
CEN EN 604-2 |
Aluminium and Aluminium Alloys - Cast Forging Stock - Part 2: Tolerances on Dimensions and Form |
|
CEN EN 635-2 |
Plywood - Classification by Surface Appearance - Part 2: Hardwood |
|
CEN EN 636 |
Plywood Specifications-Supersedes EN 636-1: 1996; EN 636-2: 1996 and EN 636-3: 1996 |
|
CEN EN 755-4 |
Aluminium and Aluminium Alloys - Extruded Rod/ Bar, Tube and Profiles - Part 4: Square Bars, Tolerances on Dimensions and Form |
|
CEN EN 828 |
Adhesives - Wettability - Determination by Measurement of Contact Angle and Critical Surface Tension of Solid Surface |
|
CEN EN ISO 105-C10 |
Textiles - Tests for colour fastness - Part C10: Colour fastness to washing with soap or soap and soda |
|
CEN EN ISO 11542-1 |
Plastics - Ultra-High-Molecular-Weight Polythylene (PE-UHMW) Moulding and Extrusion Materials - Part 1: Designation System and Basis for Specifications-ISO 11542-1: 2001 |
|
CEN EN ISO 1183-2 |
Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method-ISO 1183-2:2004 |
|
CEN EN ISO 11963 |
Plastics - Polycarbonate Sheets - Types, Dimensions and Characteristics (ISO 11963 : 1995) |
|
CEN EN ISO 1265 |
Plastics - Poly(vinyl chloride) resins - Determination of number of impurities and foreign particles |
|
CEN EN ISO 13433 |
Geosynthetics - Dynamic perforation test (cone drop test)-:1995; ISO 13433:2006 |
|
CEN EN ISO 13680 |
Petroleum and Natural Gas Industries - Corrosion-Resistant Alloy Seamless Tubes for Use as Casing, Tubing and Coupling Stock - Technical Delivery Conditions-ISO 13680:2000 |
|
CEN EN ISO 13709 |
Centrifugal pumps for petroleum, petrochemical and natural gas industries-ISO 13709: 2003 |
|
CEN EN ISO 13938-2 |
Textiles - Bursting Properties of Fabrics - Part 2: Pneumatic Method for Determination of Bursting Strength and Bursting Distension-ISO 13938-2:1999 |
|
CEN EN ISO 14692-4 |
Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation-Incorporating corrigendum July 2007 |
|
CEN EN ISO 1523 |
Determination of Flash Point - Closed Cup Equilibrium Method-ISO 1523:2002 |
|
CEN EN ISO 16070 |
Petroleum and Natural Gas Industries - Downhole Equipment - Lock Mandrels and Landing Nipples-ISO 16070: 2001; Corrected 2002-09-25 |
|
CEN EN ISO 175 |
Plastics - Methods of Test for the Determination of the Effects of Immersion in Liquid Chemicals-ISO 175:1999 |
|
CEN EN ISO 19901-1 |
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating considerations-ISO 19901-1: 2005 |
|
CEN EN ISO 19901-5 |
Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering and construction-ISO 19901-5:2003 |
|
CEN EN ISO 21415-1 |
Wheat and wheat flour - Gluten content - Part 1: Determination of wet gluten by a manual method |
|
CEN EN ISO 216 |
Writing paper and certain classes of printed matter - Trimmed sizes - A and B series, and indication of machine direction |
|
CEN EN ISO 22160 |
Milk and milk-based drinks - Determination of alkaline phosphatase activity - Enzymatic photo-activated system (EPAS) method |
|
CEN EN ISO 2535 |
Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature-ISO 2535:2001 |
|
CEN EN ISO 2898-2 |
Plastics - Plasticized Poly(Vinyl Chloride) (PVC-P) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and Determination of Properties-ISO 2898-2:1997 |
|
CEN EN ISO 294-2 |
Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars-Includes Amendment A1:2005; ISO 294-2:1996 |
|
CEN EN ISO 3093 |
Wheat, rye and respective flours, durum wheat and durum wheat semolina - Determination of the Falling Number according to Hagberg-Perten |
|
CEN EN ISO 3146 |
Plastics - Determination of Melting Behaviour (Melting Temperature or Melting Range) of Semi-Crystalline Polymers by Capillary Tube and Polarizing - Microscope Methods-ISO 3146:2000; Incorporates Corrigendum December 2002 |