|
CEN EN 24946 |
Determination of Copper Content in Steel and Cast Iron |
|
CEN EN 25077 |
Textiles - Determination of Dimensional Change in Washing and Drying (ISO 5077 : 1984) |
|
CEN EN 27627-4 |
Hardmetals - Chemical Analysis by Flame Atomic Absorption Spectrometry - Part 4: Determination of Molybdenum, Titanium and Vanadium in Contents from 0,01 to 0,5 % (m/m) (ISO 7627-4: 1983) |
|
CEN EN 314-1 |
Plywood - Bonding Quality - Part 1: Test Methods |
|
CEN EN 314-2 |
Plywood - Bonding Quality - Part 2: Requirements |
|
CEN EN 323 |
Wood-Based Panels - Determination of Density |
|
CEN EN 324-1 |
Wood-Based Panels - Determination of Dimensions of Boards Part 1: Determination of Thickness, Width and Length |
|
CEN EN 325 |
Wood-Based Panels - Determination of Dimensions of Test Pieces |
|
CEN EN 338 |
Structural Timber - Strength Classes |
|
CEN EN 350-1 |
Durability of Wood and Wood-Based Products - Natural Durability of Solid Wood Part 1: Guide to the Principles of Testing and Classification of the Natural Durability of Wood |
|
CEN EN 351-1 |
Durability of wood and wood-based products - Preservativetreated solid wood - Part 1: Classification of preservative penetration and retention |
|
CEN EN 385 |
Finger Jointed Structural Timber - Performance Requirements and Minimum Production Requirements |
|
CEN EN 386 |
Glued Laminated Timber - Performance Requirements and Minimum Production Requirements |
|
CEN EN 392 |
Glued Laminated Timber - Shear Test of Glue Lines |
|
CEN EN 3999 |
Aerospace series - Aluminium alloy AL-P2024-T351 - Sheet and strip with improved chemical milling capability 1,6 mm = a = 6 mm |
|
CEN EN 40-6 |
Lighting Columns - Part 6: Requirements for Aluminium Lighting Columns |
|
CEN EN 438-1 |
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 1: Introduction and general information-Supersedes EN 438-2:1991 |
|
CEN EN 438-6 |
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 6: Classification and specifications for Exterior-grade Compact laminates of thickness 2 mm and greater-Supersedes EN 438-1:1991 and EN 438-2:1991 |
|
CEN EN 46-1 |
Wood preservatives - Determination of the preventive action against Hylotrupes bajulus (Linnaeus) - Part 1: Larvicidial effect (Laboratory method)-Supersedes EN 46:1988 |
|
CEN EN 46-2 |
Wood preservatives - Determination of the preventive action against Hylotrupes bajulus (Linnaeus) - Part 2: Ovicidal effect (laboratory method) |
|
CEN EN 47 |
Wood preservatives - Determination of the toxic values against larvae of Hylotrupes bajulus (Linnaeus) - (Laboratory method)-Incorporating Corrigendum: August 2007 |
|
CEN EN 478 |
Unplasticized Polyvinylchloride (PVC-U) Profiles for the Fabrication of Windows and Doors - Appearance After Exposure at 150 Degrees Celsius - Test Method |
|
CEN EN 485-3 |
Aluminium and aluminium alloys Sheet, strip and plate Part 3: Tolerances on dimensions and form for hot-rolled products |
|
CEN EN 485-4 |
Aluminium and Aluminium Alloys - Sheet, Strip and Plate - Part 4: Tolerances on Shape and Dimensions for Cold-Rolled Products |
|
CEN EN 49-2 |
Wood preservatives - Determination of the protective effectiveness against Anobium punctatum (De Geer) by egglaying and larval survival - Part 2: Application by impregnation (Laboratory method) |
|
CENELEC EN 50326 |
Conductors for overhead lines - Characteristics of greases |
|
CEN EN 514 |
Unplasticized Polyvinylchloride (PVC-U) Profiles for the Fabrication of Windows and Doors - Determination of the Strength of Welded Corners and T-Joints |
|
CEN EN 524-1 |
Steel Strip Sheaths for Prestressing Tendons - Test Methods - Part 1: Determination of Shape and Dimensions |
|
CEN EN 524-2 |
Steel Strip Sheaths for Prestressing Tendons - Test Methods - Part 2: Determination of Flexural Behaviour |
|
CEN EN 524-3 |
Steel Strip Sheaths for Prestressing Tendons - Test Methods - Part 3: To-and-Fro Bending Test |
|
CEN EN 543 |
Adhesives - Determination of Apparent Density of Powder and Granule Adhesives |
|
CEN EN 572-9 |
Glass in building - Basic soda lime silicate glass products - Part 9: Evaluation of conformity/Product standard |
|
CEN EN 60 |
Glass Reinforced Plastics: Determination of the Loss on Ignition |
|
CEN EN 658-2 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 2: Determination of compression properties-Supersedes ENV 658-2: 1993 |
|
CEN EN 658-4 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 4: Determination of interlaminar shear strength by compression loading of notched test specimens-Supersedes ENV 658-4:1992 |
|
CEN EN 674 |
Glass in Building - Determination of Thermal Transmittance (U Value) - Guarded Hot Plate Method |
|
CEN EN 683-2 |
Aluminium and Aluminium Alloys - Finstock - Part 2: Mechanical Properties |
|
CEN EN 723 |
Copper and Copper Alloys - Combustion Method for Determination of Carbon on the Inner Surface of Copper Tubes or Fittings |
|
CEN EN 754-3 |
Aluminium and Aluminium Alloys - Cold Drawn Rod/ Bar and Tube - Part 3: Round Bars, Tolerances on Dimensions and Form |
|
CEN EN 754-8 |
Aluminium and Aluminium Alloys - Cold Drawn Rod/Bar and Tube - Part 8: Porthole Tubes, Tolerances on Dimensions and Form |
|
CEN EN 843-2 |
Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 2: Determination of Young's modulus, shear modulus and Poisson's ratio |
|
CEN EN 859 |
Safety of Woodworking Machines - Handfed Surface Planing Machines |
|
CEN EN 896 |
Chemicals used for treatment of water intended for human consumption - Sodium hydroxide |
|
CEN EN 898 |
Chemicals used for treatment of water intended for human consumption - Sodium hydrogen carbonate |
|
CEN EN 937 |
Chemicals Used for Treatment of Water Intended for Human Consumption - Chlorine |
|
CEN EN 939 |
Chemicals Used for Treatment of Water Intended for Human Consumption - Hydrochloric Acid |
|
CEN EN 986 |
Textile Floor Coverings - Tiles - Determination of Dimensional Changes due to the Effects of Varied Water and Heat Conditions and Distortion out of Plane |
|
CEN EN ISO 10062 |
Corrosion Tests in Artificial Atmosphere at Very Low Concentrations of Polluting Gas(es) (ISO 10062 : 1991) |
|
CEN EN ISO 10066 |
Flexible Cellular Polymeric Materials - Determination of Creep in Compression-ISO 10066: 1991 |
|
CEN EN ISO 10081-3 |
Classification of dense shaped refractory products Part 3: Basic products containing from 7 % to 50 % residual carbon-ISO 10081-3:2003; Supersedes EN 12475-3:1998 |
|
CEN EN ISO 10082 |
Plastics - Phenolic Resins - Classification and Test Methods-ISO 10082: 1999 |
|
CEN EN ISO 10405 |
Petroleum and natural gas industries - Care and use of casing and tubing |
|
CEN EN ISO 10424-2 |
Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Threading and gauging of rotary shouldered thread connections |
|
CEN EN ISO 10426-2 |
Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements-ISO 10426-2:2003 |
|
CEN EN ISO 10426-3 |
Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations-ISO 10426-3:2003 |
|
CEN EN ISO 10426-4 |
Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure-ISO 10426-4:2004 |
|
CEN EN ISO 105- B05 |
Textiles - Tests for Colour Fastness - Part B05: Detection and Assessment of Photochromism (ISO 105-B05 : 1993) |
|
CEN EN ISO 105- D01 |
Textiles - Test for Colour Fastness - Part D01: Colour Fastness to Dry Cleaning (ISO 105-D01:1993) |
|
CEN EN ISO 105- N04 |
Textiles - Test for Colour Fastness - Part N04: Colour Fastness to Bleaching - Sodium Chlorite (Severe) (ISO 105-N04:1993) |
|
CEN EN ISO 105- P01 |
Textiles - Test for Colour Fastness - Part P01: Colour Fastness to Dry Heat (Excluding Pressing) (ISO 105-P01:1993) |
|
CEN EN ISO 10519 |
Rapeseed - Determination of Chlorophyll Content - Spectrometric Method-ISO 10519:1997 |
|
CEN EN ISO 10520 |
Native Starch - Determination of Starch Content - Ewers Polarimetric Method-ISO 10520:1997 |
|
CEN EN ISO 10528 |
Textiles - Commercial Laundering Procedure for Textile Fabrics Prior to Flammability Testing (ISO 10528 : 1995) |
|
CEN EN ISO 105-A04 |
Textiles - Tests for Colour Fastness - Part A04: Method for the Instrumental Assessment of the Degree of Staining of Adjacent Fabrics-ISO 105-A04:1989 |
|
CEN EN ISO 105-A05 |
Textiles - Tests for Colour Fastness - Part A05: Instrumental Assessment of Change in Colour for Determination of Grey Scale Rating-ISO 105-A05: 1996, Including Technical Corrigendum 1: 1997 |
|
CEN EN ISO 105-B04 |
Textiles - Tests for Colour Fastness - Part B04: Colour Fastness to Artificial Weathering: Xenon Arc Fading Lamp Test-ISO 105-B04: 1994 |
|
CEN EN ISO 105-C12 |
Textiles - Tests for colour fastness - Part C12: Colour fastness to industrial laundering-ISO 105-C12:2004 |
|
CEN EN ISO 105-E02 |
Textiles Tests for colour fastness Part E02: Colour fastness to sea water-ISO 105-E02:1994 |
|
CEN EN ISO 105-E05 |
Textiles - Tests for Colour Fastness - Part E05: Colour Fastness to Spotting: Acid-ISO 105-E05:2006 |
|
CEN EN ISO 105-E12 |
Textiles Tests for colour fastness Part E12: Colour fastness to milling: Alkaline milling-ISO 105-E12: 1989 |
|
CEN EN ISO 105-E14 |
Textiles - Tests for Colour Fastness - Part E14: Colour Fastness to Acid-Felting: Mild-ISO 105-E14: 1994 |
|
CEN EN ISO 105-J02 |
Textiles - Tests for Colour Fastness - Part J02: Instrumental Assessment of Relative Whiteness-ISO 105-J02: 1997, Including Technical Corrigendum 1: 1998 |
|
CEN EN ISO 105-P02 |
Textiles - Tests for colour fastness - Part P02: Colour fastness to pleating: Steam pleating-ISO 105-P02:2002 |
|
CEN EN ISO 105-X01 |
Textiles - Tests for Colour Fastness - Part X01: Colour Fastness to Carbonizing: Aluminium Chloride (ISO 105-X01 : 1993) |
|
CEN EN ISO 105-X08 |
Textiles - Tests for Colour Fastness - Part X08: Colour Fastness to Degumming-ISO 105-X08: 1994 |
|
CEN EN ISO 105-X14 |
Textiles - Tests for Colour Fastness - Part X14: Colour Fastness to Acid Chlorination of Wool: Sodium Dichloroisocyanurate-ISO 105-X14: 1994 |
|
CEN EN ISO 105-Z01 |
Textiles - Tests for Colour Fastness - Part Z01 : Colour Fastness to Metals in the Dye-Bath: Chromium Salts (ISO 105-Z01 : 1993) |
|
CEN EN ISO 10715 |
Natural Gas - Sampling Guidelines-ISO 10715:1997 |
|
CEN EN ISO 11111-3 |
Textile machinery - Safety requirements - Part 3: Nonwoven machinery-ISO 11111-3:2005; Supersedes EN ISO 11111:1995 |
|
CEN EN ISO 11216 |
Modified Starch - Determination of Content of Carboxymethyl Groups in Carboxymethyl Starch-ISO 11216:1998 |
|
CEN EN ISO 11248 |
Plastics - Thermosetting Moulding Materials - Evaluation of Short-Term Performance at Elevated Temperatures-ISO 11248: 1993 |
|
CEN EN ISO 11402 |
Plastics - Condensation Resins - Determination of Free Formaldehyde-ISO 11402:1993; Supersedes EN ISO 9397:1997 and EN ISO 9020:1998 |
|
CEN EN ISO 11542-2 |
Plastics - Ultra-High-Molecular-Weight Polyethylene (PE-UHMW) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and Determination of Properties-ISO 11542-2:1998 |
|
CEN EN ISO 1163-2 |
Plastics - Unplasticized Poly(Vinyl Chloride) (PVC-U) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and Determination of Properties-ISO 1163-2: 1995 |
|
CEN EN ISO 11642 |
Leather - Tests for Colour Fastness - Colour Fastness to Water-ISO 11642: 1993 |
|
CEN EN ISO 11646 |
Leather - Measurement of Area-ISO 11646:1993 |
|
CEN EN ISO 11667 |
Fibre Reinforced Plastics - Mouldings Compounds and Prepregs - Determination of Resin, Reinforcement-Fibre and Mineral-Filler Content - Dissolution Methods-ISO 11667: 1997 |
|
CEN EN ISO 11816-2 |
Milk and milk products - Determination of alkaline phosphatase activity - Part 2: Fluorometric method for cheese-ISO 11816-2:2003 |
|
CEN EN ISO 12086-1 |
Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications-ISO 12086-1:2006 |
|
CEN EN ISO 12213-1 |
Natural gas Calculation of compression factor Part 1: Introduction and guidelines-ISO 12213-1:1997 |
|
CEN EN ISO 12543-1 |
Glass in Building - Laminated Glass and Laminated Safety Glass- Part 1: Definitions and Description of Component Parts-ISO 12543-1:1998 |
|
CEN EN ISO 12543-3 |
Glass in Building - Laminated Glass and Laminated Safety Glass - Part 3: Laminated Glass-ISO 12543-3:1998 |
|
CEN EN ISO 12543-5 |
Glass in Building - Laminated Glass and Laminated Safety Glass - Part 5: Dimensions and Edge Finishing-ISO 12543-5:1998 |
|
CEN EN ISO 12625-8 |
Incorporating corrigendum November 2006 |
|
CEN EN ISO 12945-1 |
Textiles - Determination of Fabric Propensity to Surface Fuzzing and to Pilling - Part 1: Pilling Box Method-ISO 12945-1:2000 |
|
CEN EN ISO 12952-4 |
Textiles - Burning Behaviour of Bedding Items - Part 4: Specific Test Methods for the Ignitability by a Small Open Flame-ISO 12952-4:1998 |
|
CEN EN ISO 12956 |
Geotextiles and Geotextile-Related Products - Determination of the Characteristic Opening Size-ISO 12956:1999 |
|
CEN EN ISO 13002 |
Carbon Fibre - Designation System for Filament Yarns-ISO 13002:1998 |
|
CEN EN ISO 13468-2 |
Plastics - Determination of the total luminous transmittance of transparent materials - Part 2: Double-beam instrument-ISO 13468-2: 1999 |
|
CEN EN ISO 13535 |
Petroleum and Natural Gas Industries - Drilling and Production Equipment - Hoistng Equipment-ISO 13535:2000 |
|
CEN EN ISO 13734 |
Natural Gas - Organic Sulfur Compounds Used as Odorants - Requirements and Test Methods-ISO 13734:1998, Including Technical Corrigendum 1:1998 |
|
CEN EN ISO 13884 |
Animal and vegetable fats and oils Determination of isolated trans isomers by infrared spectrometry-ISO 13884:2003 |
|
CEN EN ISO 139 |
Textiles - Standard atmospheres for conditioning and testing-ISO 139:2005; Supersedes EN 20139:1992 |
|
CEN EN ISO 13900 |
Steel - Determination of Boron Content - Curcumin Spectrophotometric Method After Distillation-ISO 13900: 1997 |
|
CEN EN ISO 13936-2 |
Textiles - Determination of the slippage resistance of yarns at a seam in woven fabrics - Part 2: Fixed load method-ISO 13936-2:2004 |
|
CEN EN ISO 13937-4 |
Textiles - Tear Properties of Fabrics - Part 4: Determination of Tear Force of Tongue-Shaped Test Specimens (Double Tear Method)-ISO 13937-4: 2000 |
|
CEN EN ISO 14526-3 |
Plastics - Phenolic Powder Moulding Compounds (PF-PMCs) - Part 3: Requirements for Selected Moulding Compounds-ISO 14526-3: 1999 |
|
CEN EN ISO 14527-1 |
Plastics - Urea-Formaldehyde and Urea/Melamine-Formaldehyde Powder Moulding Compounds (UF- and UF/MF-PMCs) - Part 1: Designation System and Basis for Specifications-ISO 14527-1: 1999 |
|
CEN EN ISO 14527-2 |
Plastics - Urea-Formaldehyde and Urea/Melamine-Formaldehyde Powder Moulding Compounds (UF- and UF/MF-PMCs) - Part 2: Preparation of Test Specimens and Determination of Properties-ISO 14527-2: 1999 |
|
CEN EN ISO 14527-3 |
Plastics - Urea-Formaldehyde and Urea/Melamine-Formaldehyde Powder Moulding Compounds (UF- and UF/MF-PMCs) - Part 3: Requirements for Selected Moulding Compounds-ISO 14527-3: 1999 |
|
CEN EN ISO 14529-2 |
Plastics - Melamine/Phenolic Powder Moulding Compounds (MP-PMCs) - Part 2: Preparation of Test Specimens and Determination of Properties-ISO 14529-2:1999 |
|
CEN EN ISO 14530-1 |
Plastics - Unsaturated-Polyester Powder Moulding Compounds (Up-PMCs) - Part 1: Designation System and Basis for Specifications-ISO 14530-1: 1999 |
|
CEN EN ISO 14530-3 |
Plastics - Unsaturated-Polyester Powder Moulding Compounds (Up-PMCs) - Part 3: Requirements for Selected Moulding Compounds-ISO 14530-3: 1999 |
|
CEN EN ISO 14851 |
Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous medium Method by measuring the oxygen demand in a closed respirometer-ISO 14851:1999 |
|
CEN EN ISO 15015 |
Plastics - Extruded sheets of impact-modified acrylonitrilestyrene copolymers (ABS, AEPDS and ASA) - Requirements and test methods |
|
CEN EN ISO 15106-1 |
Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 1: Humidity detection sensor method-ISO 15106-1:2003 |
|
CEN EN ISO 15106-2 |
Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 2: Infrared detection sensor method-ISO 15106-2:2003 |
|
CEN EN ISO 15136-1 |
Downhole Equipment for Petroleum and Natural Gas Industries - Progressing Cavity Pump Systems for Artificial Lift - Part 1: Pumps-ISO 15136-1:2001 |
|
CEN EN ISO 15630-3 |
Steel for the Reinforcement and Prestressing of Concrete - Test Methods - Part 3: Prestressing Steel-ISO 15630-3: 2002 |
|
CEN EN ISO 15753 |
Animal and vegetable fats and oils Determination of polycyclic aromatic hydrocarbons-ISO 15753:2003 |
|
CEN EN ISO 15797 |
Textiles - Industrial washing and finishing procedures for testing of workwear-ISO 15797:2002 |
|
CEN EN ISO 15908 |
Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives-ISO 15908: 2002 |
|
CEN EN ISO 1600 |
Plastics - Cellulose Acetate - Determination of Light Absorption on Moulded Specimens Produced Using Different Periods of Heating-ISO 1600:1990 |
|
CEN EN ISO 16035 |
Animal and vegetable fats and oils Determination of low-boiling halogenated hydrocarbons in edible oils-(ISO 16035):2003 |
|
CEN EN ISO 1624 |
Plastics - Vinyl Chloride Homopolymer and Copolymer Resins - Sieve Analysis in Water-ISO 1624: 2001; Corrected 2002-09-25 |
|
CEN EN ISO 1628-1 |
Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 1: General Principles-ISO 1628-1:1998 |
|
CEN EN ISO 16931 |
Animal and Vegetable Fats and Oils - Determination of Polymerized Triglycerides Content by High-Performance Size-Exclusion Chromatography (HPSEC)-ISO 16931:2001 |
|
CEN EN ISO 182-2 |
Plastics - Determination of the Tendency of Compounds and Products Based on Vinyl Chloride Homopolymers and Copolymers to Evolve Hydrogen Chloride and any Other Acidic Products at Elevated Temperatures - Part 2: pH Method-ISO 182-2: 1990 |
|
CEN EN ISO 18609 |
Animal and Vegetable Fats and Oils - Determination of Unsaponifiable Matter - Method Using Hexane Extraction-ISO 19609:2000; Supersedes EN ISO 3596-2:2000 |
|
CEN EN ISO 1924-2 |
Paper and Board - Determination of Tensile Properties - Part 2. Constant Rate of Elongation Method (ISO 1924-2 : 1994) |
|
CEN EN ISO 1973 |
Textile Fibres - Determination of Linear Density - Gravimetric Method and Vibroscope Method (ISO 1973 : 1995) |
|
CEN EN ISO 19902 |
Petroleum and natural gas industries - Fixed steel offshore structures |
|
CEN EN ISO 19904-1 |
Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars |
|
CEN EN ISO 2039-1 |
Plastics - Determination of hardness - Part 1: Ball indentation method-ISO 2039-1:2001 |
|
CEN EN ISO 2039-2 |
Plastics - Determination of Hardness - Part 2: Rockwell Hardness-ISO 2039-2: 1987 |
|
CEN EN ISO 2061 |
Textiles - Determination of Twist in Yarns - Direct Counting Method (ISO 2061 : 1995) |
|
CEN EN ISO 20645 |
Textile fabrics - Determination of antibacterial activity - Agar diffusion plate test-ISO 20645:2004 |
|
CEN EN ISO 20844 |
Petroleum and related products Determination of the shear stability of polymer-containing oils using a diesel injector nozzle-ISO 20844:2004 |
|
CEN EN ISO 21187 |
Milk Quantitative determination of bacteriological quality Guidance for establishing and verifying a conversion relationship between routine method results and anchor method results-ISO 21187 |
|
CEN EN ISO 22005 |
Traceability in the feed and food chain - General principles and basic requirements for system design and implementation |
|
CEN EN ISO 2286-3 |
Rubber- or Plastics-Coated Fabrics - Determination of Roll Characteristics - Part 3: Methods for Determination of Thickness-ISO 2286-3:1998 |
|
CEN EN ISO 2439 |
Flexible Cellular Polymeric Materials - Determination of Hardness (Indentation Technique)-ISO 2439:1997, Including Technical Corrigendum 1:1998 |
|
CEN EN ISO 2450 |
Cream - Determination of Fat Content - Gravimetric Method (Reference Method)-ISO 2450:1999 |
|
CEN EN ISO 2556 |
Plastics - Determination of the Gas Transmission Rate of Films and Thin Sheets under Atmospheric Pressure - Manometric Method-ISO 2556:1974 |
|
CEN EN ISO 2580-1 |
Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications-ISO 2580-1: 2002 |
|
CEN EN ISO 2589 |
Leather - Physical and mechanical tests - Determination of thickness-ISO 2589:2002 |
|
CEN EN ISO 2870 |
Surface Active Agents - Detergents - Determination of Anionic-Active Matter Hydrolyzable and Non-Hydrolyzable Under Acid Conditions (ISO 2870:1986) |
|
CEN EN ISO 2897-1 |
Plastics - Impact-Resistant Polystyrene (PS-I) Moulding and Extrusion Materials - Part 1: Designation System and Basis for Specifications-ISO 2897-1:1997 |
|
CEN EN ISO 2898-1 |
Plastics - Plasticized Poly(Vinyl Chloride) (PVC-P) Moulding and Extrusion Materials - Part 1: Designation System and Basis for Specifications-ISO 2898-1:1996 |
|
CEN EN ISO 3001 |
Plastics - Epoxy Compounds - Determination of Epoxy Equivalent-ISO 3001:1999 |
|
CEN EN ISO 3493 |
Vanilla - Vocabulary |
|
CEN EN ISO 3593 |
Starch - Determination of Ash (ISO 3593:1981) |
|
CEN EN ISO 3727-1 |
Butter - Determination of Moisture, Non-Fat Solids and Fat Contents - Part 1: Determination of Moisture Content (Reference Method)-ISO 3727-1: 2001 |
|
CEN EN ISO 3815-1 |
Zinc and zinc alloys - Part 1: Analysis of solid samples by optical emission spectrometry-Supersedes EN 12019:1997; ISO 3815-1:2005 |
|
CEN EN ISO 4044 |
Leather - Preparation of Chemical Test Samples-ISO 4044:1977 |
|
CEN EN ISO 4098 |
Leather - Chemical tests - Determination of water-soluble matter, water-soluble inorganic matter and water-soluble organic matter |
|
CEN EN ISO 4119 |
Pulps - Determination of Stock Concentration (ISO 4119 : 1995) |
|
CEN EN ISO 4263-3 |
Petroleum and related products - Determination of the ageing behaviour of inhibited oils and fluids - TOST test - Part 3: Anhydrous procedure for synthetic hydraulic fluids-ISO 4263-3:2006 |
|
CEN EN ISO 4490 |
Metallic Powders - Determination of Flow Time by Means of a Calibrated Funnel (Hall Flowmeter)-ISO 4490: 2001 |
|
CEN EN ISO 4491-3 |
Metallic powders - Determination of oxygen content by reduction methods - Part 3: Hydrogen-reducible oxygen-ISO 4491-3:1997 |
|
CEN EN ISO 4590 |
Rigid cellular plastics - Determination of the volume percentage of open cells and of closed cells-ISO 4590: 2002 |
|
CEN EN ISO 4608 |
Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride for General Use - Determination of Plasticizer Absorption at Room Temperature-ISO 4608:1998 |
|
CEN EN ISO 4611 |
Plastics - Determination of the Effects of Exposure to Damp Heat, Water Spray and Salt Mist-ISO 4611:1987 |
|
CEN EN ISO 4684 |
Leather - Chemical tests - Determination of volatile matter-ISO 4684: 2005 |
|
CEN EN ISO 4796-3 |
Laboratory Glassware - Bottles - Part 3: Aspirator Bottles-ISO 4796-3:2000 |
|
CEN EN ISO 4895 |
Plastics - Liquid Epoxy Resins - Determination of Tendency to Crystallize-ISO 4895: 1997 |
|
CEN EN ISO 5079 |
Textiles - Fibres - Determination of Breaking Force and Elongation at Break of Individual Fibres (ISO 5079 : 1995) |
|
CEN EN ISO 5080 |
Sisal Agricultural Twines-ISO 5080:1994 |
|
CEN EN ISO 5264-2 |
Pulps Laboratory beating Part 2: PFI mill method-ISO 5264-2: 2002; Supersedes EN 25264-2: 1994 |
|
CEN EN ISO 5350-1 |
Pulp - Estimation of Dirt and Shives - Part 1: Inspection of Laboratory Sheets-ISO 5350-1:2006 |
|
CEN EN ISO 5350-2 |
Pulps - Estimation of dirt and shives - Part 2: Inspection of mill sheeted pulp by transmitted light-ISO 5350-2:2006 |
|
CEN EN ISO 5398-4 |
Leather - Chemical determination of chromic oxide content - Part 4: Quantification by inductively coupled plasma - optical emission spectrometer (ICP-OES) |
|
CEN EN ISO 5399 |
Leather - Determination of Water-Soluble Magnesium Salts - EDTA Titrimetric Method-ISO 5399:1984 |
|
CEN EN ISO 5404 |
Leather Physical and mechanical tests Determination of the water resistance of heavy leathers-ISO 5404:2002 |
|
CEN EN ISO 5537 |
Dried milk - Determination of moisture content (Reference method)-ISO 5537:2004 |
|
CEN EN ISO 5555 |
Animal and Vegetable Fats and Oils - Sampling-ISO 5555: 2001 |
|
CEN EN ISO 5659-1 |
Plastics - Smoke Generation - Part 1: Guidance on Optical-Density Testing-ISO 5659-1:1996 |
|
CEN EN ISO 5764 |
Milk - Determination of Freezing Point - Thermistor Cryoscope Method (Reference Method)-ISO 5764: 2002 |
|
CEN EN ISO 5771 |
Rubber Hose and Hose Assemblies for Transferring Anhydrous Ammonia - Specification (Including Corr 1 : 1995) |
|
CEN EN ISO 60 |
Plastics - Determination of Apparent Density of Material That Can Be Poured from a Specified Funnel-ISO 60: 1977 |
|
CEN EN ISO 6144 |
Gas analysis - Preparation of calibration gas mixtures - Static volumetric method |
|
CEN EN ISO 6326-5 |
Natural Gas - Determination of Sulfur Compounds - Part 5: Lingener Combustion Method-ISO 6326-5: 1989 |
|
CEN EN ISO 658 |
Oilseeds - Determination of Content of Impurities-ISO 658: 2002 |
|
CEN EN ISO 6647-1 |
Rice - Determination of amylose content - Part 1: Reference method |
|
CEN EN ISO 7208 |
Skimmed Milk, Whey and Buttermilk - Determination of Fat Content - Gravimetric Method (Reference Method)-ISO 7208: 1999 |
|
CEN EN ISO 7384 |
Corrosion Test in Artificial Atmosphere - General Requirements (ISO 7384:1986) |
|
CEN EN ISO 7391-2 |
Plastics - Polycarbonate (PC) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and Determination of Properties-ISO 7391-2:1996 |
|
CEN EN ISO 7539-2 |
Corrosion of Metals and Alloys - Stress Corrosion Testing - Part 2: Preparation and Use of Bent-Beam Specimen (ISO 7539-2: 1989) |
|
CEN EN ISO 7539-4 |
Corrosion of Metals and Alloys - Stress Corrosion Testing - Part 4: Preparation and Use of Uniaxially Loaded Tension Specimens (ISO 7539-4: 1989) |
|
CEN EN ISO 7539-6 |
Corrosion of metals and alloys - Stress corrosion testing - Part 6: Preparation and use of pre-cracked specimens for tests under constant load or constant displacement-ISO 7539-6: 2003 |
|
CEN EN ISO 7823-3 |
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets |
|
CEN EN ISO 8254-2 |
Paper and board Measurement of specular gloss Part 2: 75 degrees gloss with a parallel beam, DIN method-ISO 8254-2:2003 |
|
CEN EN ISO 8294 |
Animal and Vegetable Fats and Oils - Determination of Copper, Iron and Nickel Contents -Graphite Furnace Atomic Absorption Method-ISO 8294: 1994 |
|
CEN EN ISO 8442-1 |
Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 1: Requirements for Cutlery for the Preparation of Food-ISO 8442-1: 1997 |
|
CEN EN ISO 8442-4 |
Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 4: Requirements for Gold-Plated Cutlery-ISO 8442-4: 1997 |
|
CEN EN ISO 8442-6 |
Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 6: Lightly Silver Plated Table Holloware Protected by Lacquer-ISO 8442-6:2000 |
|
CEN EN ISO 8442-8 |
Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 8: Specification for Silver Table and Decorative Holloware-ISO 8442-8:2000 |
|
CEN EN ISO 8895 |
Shaped insulating refractory products - Determination of cold crushing strength-ISO 8895: 2004;: 1995 |
|
CEN EN ISO 8974 |
Plastics - Phenolic Resins - Determination of Residual Phenol Content by Gas Chromatography-ISO 8974: 2002 |
|
CEN EN ISO 9054 |
Cellular Plastics, Rigid - Test Methods for Self-Skinned, High-Density Materials-ISO 9054:1990 |
|
CEN EN ISO 9073-10 |
Textiles - Test methods for nonwovens - Part 10: Lint and other particles generation in the dry state-ISO 9073-10:2003 |
|
CEN EN ISO 9073-8 |
Textiles - Test Methods for Nonwovens - Part 8: Determination of Liquid Strike-Through Time (Simulated Urine)-ISO 9073-8:1995 |
|
CEN EN ISO 9163 |
Textile glass - Rovings - Manufacture of test specimens and determination of tensile strength of impregnated rovings-ISO 9163:2005 |
|
CEN EN ISO 9653 |
Adhesives - Test Method for Shear Impact Strength of Adhesives Bonds-ISO 9653: 1998; Supersedes EN 29653: 1994 |
|
CEN EN ISO 9706 |
Information and Documentation - Paper for Documents - Requirements for Permanence-ISO 9706: 1994 |
|
CEN EN ISO 9902-5 |
Textile Machinery - Noise Test Code - Part 5: Weaving and Knitting Preparatory Machinery-ISO 9902-5:2001 |
|
CEN EN ISO 9944 |
Plastics - Phenolic Resins - Determination of Electrical Conductivity of Resin Extracts (ISO 9944 : 1990) |
|
CEN ENV 1006 |
Advanced technical ceramics - Monolithic ceramics - Guidance on the selection of test pieces for the evaluation of properties |
|
CEN ENV 1402-8 |
Unshaped Refractory Products - Part 8: Determination of Complementary Properties |
|
CEN ENV 14272 |
Plywood - Calculation Method for Some Mechanical Properties |
|
CEN ENV 1927-1 |
Qualitative Classification of Softwood Round Timber - Part 1: Spruces and Firs |
|
CEN ENV 820-4 |
Advanced Technical Ceramics - Monolithic Ceramics - Thermomechanical Properties - Part 4: Determination of Flexural Creep Deformation at Elevated Temperatures |
|
CENELEC HD 547 S1 |
Conductive Clothing for Live Working at a Nominal Voltage up to 800 KV a.c. |
|
CEN 10426-1:00PRA1 |
Petroleum and Natural Gas Industries - Cements and Materials for Well Cementing - Part 1: Specification-ISO 10426-1:2000/DAM 1 |
|
CEN CEN ISO/TS 17226 |
Leather - Chemical tests - Determination of formaldehyde content-ISO/TS 17226:2003 |
|
CEN CEN/TR 10347 |
Guidance for forming of structural steels in processing |
|
CEN CEN/TR 14739 |
Scheme for carrying out a risk assessment for flammable refrigerants in case of household refrigerators and freezers |
|
CEN CEN/TR 15019 |
Geotextiles and geotextile-related products - On-site quality control |
|
CEN CEN/TR 15046 |
Wood preservatives - Artificial weathering of treated wood prior to biological testing - UV-radiation and water-spraying procedure |
|
CEN CEN/TS 13130-15 |
Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 15: Determination of 1,3- butadiene in food simulants |
|
CEN CEN/TS 13130-19 |
Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 19: Determination of dimethylaminoethanol in food simulants |
|
CEN CEN/TS 13130-24 |
Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 24: Determination of maleic acid and maleic anhydride in food simulants |
|
CEN CEN/TS 13130-25 |
Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 25: Determination of 4- methyl-1-pentene in food simulants |
|
CEN CEN/TS 14417 |
Geosynthetic barriers - Test method for the determination of the influence of wetting-drying cycles on the permeability of clay geosynthetic barriers |
|
CEN CEN/TS 14778-2 |
Solid biofuels - Sampling - Part 2: Methods for sampling particulate material transported in lorries |
|
CEN CEN/TS 15003 |
Durability of wood and wood-based products - Criteria for hot air processes for curative uses against wood destroying organisms |
|
CEN CEN/TS 15103 |
Solid biofuels - Methods for the determination of bulk density |
|
CEN CEN/TS 15290 |
Solid Biofuels - Determination of major elements |
|
CEN CEN/TS 15296 |
Solid Biofuels - Calculation of analyses to different bases |
|
CEN CEN/TS 15358 |
Solid recovered fuels - Quality management systems - Particular requirements for their application to the production of solid recovered fuels |
|
CEN CEN/TS 15398 |
Resilient, textile and laminate floor coverings - Floor covering standard symbols |
|
CEN CEN/TS 15404 |
Solid recovered fuels - Methods for the determination of ash melting behaviour by using characteristic temperatures |
|
CEN CEN/TS 15411 |
Solid recovered fuels - Methods for the determination of the content of trace elements (As, Ba, Be, Cd, Co, Cr, Cu, Hg, Mo, Mn, Ni, Pb, Sb, Se, Tl, V and Zn) |
|
CEN CEN/TS 15415 |
Solid recovered fuels - Determination of particle size distribution by screen method |
|
CEN CEN/TS 15439 |
Biomass gasification - Tar and particles in product gases - Sampling and analysis |
|
CEN CEN/TS 15442 |
Solid recovered fuels - Methods for sampling |
|
CEN CEN/TS 15534-1 |
Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products |
|
CEN CEN/TS 15534-2 |
Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials |
|
CEN CEN/TS 15639 |
Solid recovered fuels - Methods for the determination of mechanical durability of pellets |
|
CEN CEN/TS 15658 |
Advanced technical ceramics - Mechanical properties of ceramic fibres at high temperature under non-reactive environment - Determination of creep behaviour by the hot end method |
|
CEN CEN/TS 635-4 |
Plywood - Classification by surface appearance - Part 4: Parameters of ability for finishing, guideline |
|
CEN CEN/TS 843-6 |
Advanced technical ceramics - Monolithic ceramics. Mechanical properties at room temperature - Part 6: Guidance for fractographic investigation |
|
CEN CR 14244 |
Durability of Wood and Wood-Based Products - Recommendations for Measurement of Emissions to the Environment from Treated Wood in Service |
|
CEN EN 10016-3 |
Non-Alloy Steel Rod for Drawing and/or Cold Rolling - Part 3: Specific Requirements for Rimmed and Rimmed Substitute Low Carbon Steel Rod |
|
CEN EN 10016-4 |
Non-Alloy Steel Rod for Drawing and/or Cold Rolling - Part 4: Specific Requirements for Rod for Special Applications |
|
CEN EN 10031 |
Semi-finished products for forging - Tolerances on dimensions shape and mass |
|
CEN EN 10120 |
Steel Sheet and Strip for Welded Gas Cylinders |
|
CEN EN 1014-2 |
Wood Preservatives - Creosote and Creosoted Timber - Methods of Sampling and Analysis - Part 2: Procedure for Obtaining a Sample of Creosote from Creosoted Timber for Subsequent Analysis |
|
CEN EN 10200 |
Chemical Analysis of Ferrous Materials - Determination of Boron in Steel - Spectrophotometric Method |
|
CEN EN 10213 |
Steel castings for pressure purposes |
|
CEN EN 10218-2 |
Steel Wire and Wire Products - General - Part 2: Wire Dimensions and Tolerances |
|
CEN EN 10244-3 |
Steel Wire and Wire Products - Non-Ferrous Metallic Coatings on Steel Wire - Part 3: Aluminium Coatings |
|
CEN EN 10244-4 |
Steel Wire and Wire Products - Non-Ferrous Metallic Coatings on Steel Wire - Part 4: Tin Coatings |
|
CEN EN 10246-18 |
Non-Destructive Testing of Steel Tubes - Part 18: Magnetic Particle Inspection of Tube Ends of Seamless and Welded Ferromagnetic Steel Tubes for the Detection of Laminar Imperfections |
|
CEN EN 10246-3 |
Non-Destructive Testing of Steel Tubes - Part 3: Automatic Eddy Current Testing of Seamless and Welded (Except Submerged Arc-Welded) Steel Tubes for the Detection of Imperfections |
|
CEN EN 10246-7 |
Non-destructive testing of steel tubes - Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc welded) tubes for the detection of longitudinal imperfections |
|
CEN EN 10248-1 |
Hot Rolled Sheet Piling of Non Alloy Steels - Part 1: Technical Delivery Conditions |
|
CEN EN 10251 |
Magnetic Materials - Methods of Determination of the Geometrical Characteristics of Electrical Steel Sheet and Strip |
|
CEN EN 10253-2 |
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
|
CEN EN 10276-1 |
Chemical Analysis of Ferrous Materials - Determination of Oxygen in Steel and Iron - Part 1: Sampling and Preparation of Steel Samples for Oxygen Determination |
|
CEN EN 10291 |
Metallic Materials - Uniaxial Creep Testing in Tension - Method of Test |
|
CEN EN 103 |
Ceramic Tiles - Determination of Linear Thermal Expansion |
|
CEN EN 10304 |
Magnetic Materials (Iron and Steel) for Use in Relays |
|
CEN EN 10324 |
Steel wire and wire products - Hose reinforcement wire |
|
CEN EN 10335 |
Steel for packaging - Flat steel products intended for use in contact with foodstuffs, products or beverages for human and animal consumption - Non alloyed electrolytic chromium/chromium oxide coated steel |
|
CEN EN 10341 |
Cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state-Supersedes EN 10126:1995, EN 10165:1995 |
|
CEN EN 105 |
Ceramic Tiles - Determination of Crazing Resistance - Glazed Tiles |
|
CEN EN 1071-4 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 4: Determination of chemical composition by electron probe microanalysis (EPMA)-Supersedes ENV 1071-4: 1995 |
|
CEN EN 1071-6 |
Advanced technical ceramics Methods of test for ceramic coatings Part 6: Determination of the abrasion resistance of coatings by a micro-abrasion wear test |
|
CEN EN 1114-2 |
Rubber and Plastics Machines - Extruders and Extrusion Lines - Part 2: Safety Requirements for Die Face Pelletizers |
|
CEN EN 1134 |
Fruit and Vegetable Juices - Determination of Sodium, Potassium, Calcium and Magnesium Content by Atomic Absorption Spectrometry (AAS) |
|
CEN EN 1183 |
Materials and Articles in Contact with Foodstuffs - Test Methods for Thermal Shock and Thermal Shock Endurance |
|
CEN EN 1186-11 |
Materials and articles in contact with foodstuffs - Plastics - Part 11: Test methods for overall migration into mixtures of C-labelled synthetic triglycerides |
|
CEN EN 1186-13 |
Materials and articles in contact with foodstuffs Plastics Part 13: Test methods for overall migration at high temperatures |
|
CEN EN 1186-14 |
Materials and articles in contact with foodstuffs Plastics Part 14: Test methods for substitute tests™ for overall migration from plastics intended to come into contact with fatty foodstuffs using test media iso-octane and 95% ethanol |
|
CEN EN 1186-15 |
Materials and articles in contact with foodstuffs Plastics Part 15: Alternative test methods to migration into fatty food simulants by rapid extraction into iso-octane and/or 95% ethanol |
|
CEN EN 1186-5 |
Materials and Articles in Contact with Foodstuffs - Plastics - Part 5: Test Methods for Overall Migration into Aqueous Food Simulants by Cell-Supersedes ENV 1186-5: 1994 |
|
CEN EN 1186-8 |
Materials and Articles in Contact with Foodstuffs - Plastics - Part 8: Test Methods for Overall Migration into Olive Oil by Article Filling-Supersedes ENV 1186-8: 1994 |
|
CEN EN 1199 |
Chemicals used for treatment of water intended for human consumption - Disodium hydrogen orthophosphate |
|
CEN EN 1201 |
Chemicals Used for Treatment of Water Intended for Human Consumption - Potassium Dihydrogen Orthophosphate |
|
CEN EN 12014-4 |
Foodstuffs - Determination of nitrate and/or nitrite content - Part 4: Ion-exchange chromatographic (IC) method for the determination of nitrate and nitrite content of meat products-Supersedes ENV 12014-4:1998 |
|
CEN EN 12026 |
Self Adhesive Tapes - Measurement of the Unwinding Force at High Speed |
|
CEN EN 12027 |
Self Adhesive Tapes - Measurement of Flame Resistance |
|
CEN EN 12032 |
Self-Adhesive Tapes - Measurement of Bonding of Thermosetting Adhesive Tapes During Curing |
|
CEN EN 12033 |
Self-Adhesive Tapes - Measurement of Bonding of Thermosetting Adhesive Tapes After Curing |
|
CEN EN 12035 |
Self-Adhesive Tapes - Flagging of Adhesive Tape |
|
CEN EN 12041 |
Food Processing Machinery - Moulders - Safety and Hygiene Requirements |
|
CEN EN 12043 |
Food Processing Machinery - Intermediate Provers - Safety and Hygiene Requirements |
|
CEN EN 1205 |
Chemicals used for treatment of water intended for human consumption - Disodium dihydrogen pyrophosphate |
|
CEN EN 12061 |
Plastic Piping Systems - Thermoplastics Fittings - Test Method for Impact Resistance |
|
CEN EN 12104 |
Resilient Floor Coverings - Cork Floor Tiles - Specification |
|
CEN EN 12133 |
Fruit and Vegetable Juices - Determination of Chloride Content - Potentiometric Titration Method |
|
CEN EN 12165 |
Copper and Copper Alloys - Wrought and Unwrought Forging Stock |
|
CEN EN 12203 |
Footwear, leather and imitation leather goods manufacturing machines - Shoe and leather presses - Safety requirements-Incorporating Corrigendum July 2006 |
|
CEN EN 12240 |
Touch and Close Fasteners - Determination of the Overall and Effective Widths of Tapes and the Effective Width of a Closure |
|
CEN EN 12281 |
Printing and business paper - Requirements for copy paper for dry toner imaging processes-Supersedes ENV 12281: 1996 |
|
CEN EN 12283 |
Printing and business paper - Determination of toner adhesion-Supersedes ENV 12283: 1996 |
|
CEN EN 12289 |
Advanced technical ceramics - Mechanical properties of ceramic composites at ambient temperature - Determination of in-plane shear properties |
|
CEN EN 1229 |
Plastics Piping Systems - Glass-Reinforced Thermosetting Plastics (GRP) Pipes and Fittings - Test Methods to Prove the Leaktightness of the Wall Under Short-Term Internal Pressure |
|
CEN EN 12301 |
Rubber and Plastics Machines - Calenders - Safety Requirements |